没有合适的资源?快使用搜索试试~ 我知道了~
(R2021) MIL-PRF-25435D_1_NOT_2-004.pdf
1.该资源内容由用户上传,如若侵权请联系客服进行举报
2.虚拟产品一经售出概不退款(资源遇到问题,请及时私信上传者)
2.虚拟产品一经售出概不退款(资源遇到问题,请及时私信上传者)
版权申诉
0 下载量 10 浏览量
2023-07-21
11:18:29
上传
评论
收藏 260KB PDF 举报
温馨提示
试读
14页
(R2021) MIL-PRF-25435D_1_NOT_2-004.pdf
资源推荐
资源详情
资源评论
AMSC N/A FSC 6620
MIL-PRF-25435D
w/AMENDMENT 1
1 November 2011
SUPERSEDING
MIL-PRF-25435D
3 July 2008
PERFORMANCE SPECIFICATION
TRANSMITTERS, PRESSURE, AIRCRAFT
GENERAL SPECIFICATION FOR
INCH-POUND
Comments, suggestions, or questions on this document should be addressed to: Oklahoma City
Air Logistics Center/ENSDAA, 3001 Staff Drive, Tinker AFB, OK 73145-3036 or emailed to
af71@tinker.af.mil. Since contact information can change, you may want to verify the currency
of this address information using the ASSIST Online database at https:assist.daps.dla.mil.
Source: https://assist.dla.mil -- Downloaded: 2021-05-18T00:20Z
Check the source to verify that this is the current version before use.
MIL-PRF-25435D w/AMENDMENT 1
2
This specification is approved for use by all Departments and Agencies of Department of
Defense.
1. SCOPE
1.1 Scope. This specification covers the general requirements for aircraft pressure transmitters.
2. APPLICABLE DOCUMENTS
2.1 General. The documents listed in this section are cited in sections 3, 4, or 5 of this
specification. This section does not include documents cited in other sections of this
specification or recommended for additional information or as examples. While every effort has
been made to ensure the completeness of these lists, document users are cautioned that they must
meet the requirements specified in the documents cited in sections 3, 4, or 5 of this specification,
whether or not they are listed.
2.2 Government documents.
2.2.1 Specifications, standards and handbooks. The following specifications, standards, and
handbooks form a part of this document to the extent specified herein. Unless otherwise
specified, the issues of these documents are those cited in the solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATIONS
MIL-I-25437 - Indicators, Aircraft, Pressure, Voltage Ratio Type, General
Specification For
MIL-PRF-7808 - Lubricating Oil, Aircraft Turbine Engine, Synthetic Base
MS33678 - Connector, Receptacle, Electrical, Integral Mounting
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-461 - Requirements for the Control of Electromagnetic Interference
Characteristics of Subsystems and Equipment
MIL-STD-704 - Aircraft Electric Power Characteristics
MIL-STD-810 - Environmental Test Methods
(Copies of these documents are available online at https:assist.daps.dla.mil/quicksearch/ or
from the Standardization Documents Order Desk, 700 Robbins Avenue, Building 4D,
Philadelphia, PA 19111-5094.)
2.3. Non-Government publications. The following documents form a part of this document to
the extent specified herein. Unless otherwise specified, the issues of these documents are
those cited in the solicitation or contract.
Source: https://assist.dla.mil -- Downloaded: 2021-05-18T00:20Z
Check the source to verify that this is the current version before use.
MIL-PRF-25435D w/AMENDMENT 1
3
AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)
ASTM B117 - Standard Practice for Operating Salt Spray (Fog) Testing Apparatus
(ASTM documents may be obtained at www.astm.org <http://www.astm.org> or addressed to
the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohocken,
PA 19428-2959.)
SAE INTERNATIONAL
SAE AS8879 - Screw Threads - UNJ Profile, Inch
Controlled Radius Root with Increased Minor Diameter
SAE AS5202 - Port or Fitting End, Internal Straight Thread
(SAE documents may be obtained at www.sae.org <http://www.sae.org/> or from Society of
Automotive Engineers, Inc., 400 Commonwealth Drive, Warrendale PA 15096.)
2.4 Order of precedence. Unless otherwise noted herein or in the contract, in the event of a
conflict between the text of this document and the references cited herein, the test of this
document takes precedence. Nothing in this document, however, supersedes applicable laws and
regulations unless a specific exemption has been obtained.
3. REQUIREMENTS
3.1 First article. When specified (see 6.2), the transmitter shall be subjected to first article
inspection in accordance with 4.2.
3.2 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or
environmentally preferable materials should be used to the maximum extent possible
provided that the materials meet or exceed the operational and maintenance requirements,
and promote economically advantageous life cycle cost.
3.3 Materials. Unless otherwise specified, materials shall be nonmagnetic, nonferrous, and shall
be compatible with titanium alloys. Materials shall not produce deleterious fumes, and shall
be treated to resist corrosion due to electrolytic decomposition, fungus, salt spray, alcohol,
fuels, oils, hydraulic fluids, and any other conditions that may be encountered during
operational use or storage. No liquid such as silicone oil is to be used to fill the transmitter
without the specific approval of the preparing activity.
3.4 Interface.
3.4.1 Dimensions. The transmitter case shall conform to the dimensions in Figure 1.
3.4.2 Pressure indicator. The transmitter shall be designed for operation with indicators
conforming to the requirements of MIL-I-25437.
Source: https://assist.dla.mil -- Downloaded: 2021-05-18T00:20Z
Check the source to verify that this is the current version before use.
剩余13页未读,继续阅读
资源评论
phyit
- 粉丝: 7648
- 资源: 2803
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功