没有合适的资源?快使用搜索试试~ 我知道了~
TI-BQ24392.pdf
需积分: 5 0 下载量 182 浏览量
2022-12-01
23:36:15
上传
评论 4
收藏 1.32MB PDF 举报
温馨提示
试读
21页
TI-BQ24392.pdf
资源推荐
资源详情
资源评论
Copyright © 2017, Texas Instruments Incorporated
Product
Folder
Order
Now
Technical
Documents
Tools &
Software
Support &
Community
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
English Data Sheet: SLIS146
BQ24392
ZHCS958G –JUNE 2012–REVISED SEPTEMBER 2017
支支持持 USB 电电池池充充电电规规范范版版本本 1.2 检检测测功功能能的的 BQ24392 双双路路 SPST USB
2.0 高高速速开开关关
1
1 特特性性
1
• USB 2.0 高速开关
• 检测符合 USB 电池充电规范版本 1.2 (BCv1.2) 的
充电器
• 兼容附件
– 专用充电端口
– 标准下行端口
– 充电下行端口
• 非标准充电器
– Apple™充电器
– TomTom™充电器
– 不符合电池充电规范版本 1.2 (BCv1.2) 的 USB
充电器
• –2V 至 28V VBUS 电压范围
• 静电放电 (ESD) 性能经测试符合 JESD 22 规范
– 4000V 人体放电模式
– 1500V 组件充电模式 (C101)
• 至接地 (GND) 的 ESD 性能 DP_CON/DM_CON
– ±8kV 接触放电 (IEC 61000-4-2)
2 应应用用
• 移动电话
• 智能手机
• 摄像机
• GPS 系统
3 说说明明
BQ24392 是一款具有充电器检测功能的双路单刀单掷
(SPST) USB 2.0 高速隔离开关,可与 micro-USB 和
mini-USB 端口搭配使用。凭借这款 USB 开关,移动
电话、平板电脑和其它电池供电型电子设备可通过不同
适配器充电,并且系统软件需求最低。该器件的充电器
检测电路可支持符合 USB 电池充电规范版本 1.2
(BCv1.2) 的 Apple™、TomTom™ 以及其它非标准充
电器。
当 micro-USB 或 mini-USB 端口连接充电器
时,BQ24392 器件由 VBUS 供电,可承受 28V 电
压,无需外部保护。
器器件件信信息息
(1)
器器件件型型号号 封封装装 封封装装尺尺寸寸((标标称称值值))
BQ24392 UQFN (10) 2.05mm x 1.55mm
(1) 要了解所有可用封装,请参见数据表末尾的可订购产品附录。
空白
空白
USB 开开关关的的 480Mbps USB 2.0 眼眼图图
2
BQ24392
ZHCS958G –JUNE 2012–REVISED SEPTEMBER 2017
www.ti.com.cn
Copyright © 2012–2017, Texas Instruments Incorporated
目目录录
1 特特性性.......................................................................... 1
2 应应用用.......................................................................... 1
3 说说明明.......................................................................... 1
4 修修订订历历史史记记录录 ........................................................... 2
5 Pin Configuration and Functions......................... 3
6 Specifications......................................................... 4
6.1 Absolute Maximum Ratings ...................................... 4
6.2 ESD Ratings.............................................................. 4
6.3 Recommended Operating Conditions....................... 4
6.4 Thermal Information.................................................. 4
6.5 Electrical Characteristics........................................... 5
6.6 Typical Characteristics.............................................. 5
7 Detailed Description.............................................. 6
7.1 Overview ................................................................... 6
7.2 Functional Block Diagram ......................................... 6
7.3 Feature Description................................................... 7
7.4 Device Functional Modes.......................................... 8
8 Application and Implementation .......................... 9
8.1 Application Information.............................................. 9
8.2 Typical Application ................................................. 10
9 Power Supply Recommendations...................... 11
10 Layout................................................................... 12
10.1 Layout Guidelines ................................................. 12
10.2 Layout Example .................................................... 13
11 器器件件和和文文档档支支持持 ..................................................... 14
11.1 接收文档更新通知 ................................................. 14
11.2 社区资源................................................................ 14
11.3 商标 ....................................................................... 14
11.4 静电放电警告......................................................... 14
12 机机械械、、封封装装和和可可订订购购信信息息....................................... 14
4 修修订订历历史史记记录录
Changes from Revision F (July 2017) to Revision G Page
• Changed R
ON
From: 8 Ω TYP To: 3.5 Ω TYP, 6.9 Ω MAX in the Electrical Characteristic table .......................................... 5
Changes from Revision E (February 2017) to Revision F Page
• Changed CHG_DET diode direction from right facing to left facing in Application Schematic. .......................................... 10
Changes from Revision D (January 2016) to Revision E Page
• 从 BQ24932 更改为 BQ24392(在
说明)
.............................................................................................................................. 1
• Changed From: BQ24932 To: BQ24392 in the Overview...................................................................................................... 6
• Changed title From: Using the BQ24932 GPIOs To: Using the BQ24392 GPIOs................................................................. 9
Changes from Revision C (January 2015) to Revision D Page
• Changed diode direction from left facing to right facing in Application Schematic. ............................................................. 10
Changes from Revision B (October 2014) to Revision C Page
• 更新了 特性。 ......................................................................................................................................................................... 1
Changes from Revision A (June 2012) to Revision B Page
• 添加了 ESD
额定值
表、
特性 说明
部分、
器件功能模式
、
应用和实施
部分、
电源相关建议
部分、
布局
部分、
器件和
文档支持
部分以及
机械、封装和可订购信息
部分。............................................................................................................... 1
1
2
3
4
5
6
7
8
9
10
CHG_DET
SW_OPEN
DM_HOST
DP_HOST
CHG_AL_N
GND
GOOD_BAT
DP_CON
DM_CON
VBUS
Copyright © 2017, Texas Instruments Incorporated
3
BQ24392
www.ti.com.cn
ZHCS958G –JUNE 2012–REVISED SEPTEMBER 2017
Copyright © 2012–2017, Texas Instruments Incorporated
5 Pin Configuration and Functions
RSE Package
10-Pin (UQFN)
(Top View)
Pin Functions
PIN
I/O DESCRIPTION
NO. NAME
1 SW_OPEN O
USB switch status indicator
Open-drain output. 10kΩ external pull-up resistor required
SW_OPEN = LOW indicates when switch is connected
SW_OPEN = HIGH-Z indicates when then switch is not connected
2 DM_HOST I/O D– signal to transceiver
3 DP_HOST I/O D+ signal to transceiver
4 CHG_AL_N O
Charging status indicator
Open-drain output. 10kΩ external pull-up resistor required
CHG_AL_N = LOW indicates when charging is allowed
CHG_AL_N = HIGH-Z indicates when charging is not allowed
5 GOOD_BAT I
Battery status indication from system
GOOD_BAT = LOW indicates a dead battery
GOOD_BAT = HIGH indicates a good battery
6 GND - Ground
7 DP_CON I/O D+ signal from USB connector
8 DM_CON I/O D– signal from USB connector
9 VBUS I Supply pin from USB connector
10 CHG_DET O
Charger detection indicator
Push-Pull output to system
CHG_DET = LOW indicates when a charger is not detected
CHG_DET = HIGH indicates when a charger detected
4
BQ24392
ZHCS958G –JUNE 2012–REVISED SEPTEMBER 2017
www.ti.com.cn
Copyright © 2012–2017, Texas Instruments Incorporated
6 Specifications
6.1 Absolute Maximum Ratings
over –40℃ to 85℃ temperature range (unless otherwise noted)
MIN MAX UNIT
Input Voltage
VBUS –2 28 V
CHG_AL_N –2 28 V
DM_HOST –0.3 7
V
DP_HOST –0.3 7
GOOD_BAT –0.3 7
DP_CON –0.3 7
DM_CON –0.3 7
CHG_DET –0.3 7
T
stg
Storage temperature range 65 150 °C
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Manufacturing with
less than 500-V HBM is possible with the necessary precautions.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. Manufacturing with
less than 250-V CDM is possible with the necessary precautions.
6.2 ESD Ratings
VALUE UNIT
V
(ESD)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001
(1)
±4000
V
Charged-device model (CDM), per JEDEC specification JESD22-
C101
(2)
±1500
IEC Contact discharge pins DP_CON and DM_CON to GND ±8000
6.3 Recommended Operating Conditions
MIN MAX UNIT
VBUS 4.75 5.25 V
GOOD_BAT 0 VBUS
DM_HOST 0 3.6
DP_HOST 0 3.6
DM_CON 0 3.6
DP_CON 0 3.6
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
6.4 Thermal Information
THERMAL METRIC
(1)
bq24392
UNITRSE
10 PINS
R
θJA
Junction-to-ambient thermal resistance 167.7 °C/W
R
θJC(top)
Junction-to-case (top) thermal resistance 78.8 °C/W
R
θJB
Junction-to-board thermal resistance 95.8 °C/W
ψ
JT
Junction-to-top characterization parameter 4.7 °C/W
ψ
JB
Junction-to-board characterization parameter 95.9 °C/W
Copyright © 2017, Texas Instruments Incorporated
Copyright © 2017, Texas Instruments Incorporated
5
BQ24392
www.ti.com.cn
ZHCS958G –JUNE 2012–REVISED SEPTEMBER 2017
Copyright © 2012–2017, Texas Instruments Incorporated
(1) CHG_DET max value will be clamped at 7 V when V
VBUS
> 7 V
6.5 Electrical Characteristics
V
BUS
= 4.5 V to 5.5 V, T
A
= –40°C to 85°C (unless otherwise noted)
(1)
PARAMETER TEST CONDITIONS MIN TYP MAX UNIT
V
VBUS_VALID
VBUS Valid threshold Rising VBUS threshold 3.5 V
V
OH
CHG_DET CHG_DET I
OH
= –2 mA 3.5 VBUS V
V
OL
CHG_DET, SW_OPEN,
CHG_AL_N
CHG_DET,
SW_OPEN,
CHG_AL_N
I
OL
= 2 mA 0.4 V
V
IH
High-level input voltage
GOOD_BAT
1.1 V
V
IL
Low-level input voltage 0.5 V
R
PD
Internal pull-down
resistance
950 kΩ
t
DBP
Dead battery provision timer 32 45 Mins
V
USBIO
ON- state resistance match
between
DM_CON,
DP_CON,
DM_HOST,
DP_HOST
0 3.6 V
R
ON
ON-state resistance
V
DM_HOST
and V
DP_HOST
= 0 to 3.6 V, I
DP_CON
and I
DM_CON
= –2 mA
3.5 6.9 Ω
R
ON
(flat)
ON-state resistance
flatness
1.1 Ω
ΔR
ON
ON- state resistance match
between channels
V
DM_HOST
and V
DP_HOS
T = 0.4 V, I
DP_CON
and
I
DM_CON
= –2 mA
0.5 Ω
I
CC-SW (ON)
Current consumption
V
VBUS
= 5V,
V
IH(GOOD_BAT)
= 1.1 V
250 µA
V
VBUS
= 5 V,
V
IH(GOOD_BAT)
= 2.5 V
80 µA
I
CC-SW (OFF)
Current consumption with USB switch off V
VBUS
= 5 V; USB Switch OFF 45 µA
I
USBI/O (ON)
Leakage current with USB switch on
V
DM_HOST
and V
DP_HOST
= 0 to 3.6 V, I
DP_CON
and I
DM_CON
= –2 mA
50 nA
I
USBI/O (OFF)
Leakage current with USB switch off 45 nA
C
I(OFF)
Capacitance with USB
switch off
DP_HOST,
DM_HOST
DC bias = 0 V or 3.6 V, f = 10 MHz
2 pF
C
O(OFF)
Capacitance with USB
switch off
DP_CON,
DM_CON
10 pF
C
I(ON)
Capacitance with USB
switch on
DP_HOST,
DM_HOST
11 pF
C
O(ON)
Capacitance with USB
switch on
DP_CON,
DM_CON
11 pF
BW Bandwidth R
L
= 50 Ω, Switch ON 920 MHz
O
ISO
Isolation with USB switch off f = 240 MHz, R
L
= 50 Ω, Switch OFF –26 dB
X
TALK
Crosstalk f = 240 MHz, R
L
= 50 Ω –30.5 dB
6.6 Typical Characteristics
Figure 1. 480-Mbps USB 2.0 Eye Diagram with No Device Figure 2. 480-Mbps USB 2.0 Eye Diagram with USB Switch
剩余20页未读,继续阅读
资源评论
不觉明了
- 粉丝: 3119
- 资源: 5348
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功