SJA1105PQRS数据手册.pdf

The SJA1105P/Q/R/S is a 5-port automotive Ethernet switch supporting IEEE Audio Video Bridging (AVB) and Time-Sensitive Networking (TSN) standards. Each of the five ports can be individually configured to operate at 10/100/1000 Mbit/s. This feature provides the flexibility to connect any Fast/Gigabit/optical PHY or MCU/MPU to any of the ports. Examples of external PHYs are the TJA1100 and TJA1102 IEEE 100BASE-T1 PHYs from NXP Semiconductors

车载以太网PHY TJA1101A用户手册.pdf

This reference document describes the configuration, register structure and mapping of the TJA1101A Ethernet PHY.

车载以太网PHY TJA1101B数据手册.pdf

The TJA1101B is a 100BASE-T1-compliant Ethernet PHY optimized for automotive use cases such as gateways, IP camera links, radar modules, driver assistance systems and back-bone networks. The device provides 100 Mbit/s transmit and receive capability over a single unshielded twisted-pair cable, supporting a cable length of up to at least 15 m. The TJA1101B has been designed for automotive robustness and ISO 26262, ASIL-A compliance, while minimizing power consumption and system costs.

原理图TJA1100.pdf

车载以太网PHY TJA1100参考评估板原理图PCB

车载以太网PHY TJA1100评估板用户手册.pdf

This document describes the usage of the TJA1100 Customer Evaluation Board. The Board supports the evaluation of the TJA1100 with providing (MII) a 40-pins standard header (including MII/SMI/control signals/power supplies. Details can be found in section 2.3.1) with 2,54mm pinning distance to a host controller board, the bus interface (MDI) including a srew terminal (SMKDS) connector as well as needed components for the power supply and operation. Further information is given in the following sections.

PXISPEC20.pdf

This SPEC describes the primary objectives and scope of the PCI eXtensions for Instrumentation (PXI) specification. It also defines the intended audience and lists relevant terminology and documents.

FMC FPGA标准接口卡规范-VITA57.1.pdf

This standard describes FMC IO modules and introduces an electro-mechanical standard that creates a low overhead protocol bridge. This is between the front panel IO, on the mezzanine module, and an FPGA processing device on the carrier card, which accepts the mezzanine module.

PICMG 2.11.pdf

PICMG 2.11 defines the electrical and mechanical interfaces, and minimum requirements for modular CompactPCI pluggable power supplies and related CompactPCI platforms based on the CompactPCI core specification PICMG 2.0 R2.1. Although the CompactPCI core specification PICMG 2.0 R2.1 defines an optional pluggable power supply connector interface; this interface is inadequate to support many higher power applications. This specification, PICMG 2.1, provides a defined interface to support higher power supply output current levels and 6U form factor power supplies, as well as providing some additional functionality to support Hot Swap applications, and a growth path for high availability systems.

PICMG 2.5.pdf

The goal of this specification is to extend the capabilities and utility of the CompactPCI 6U based system architecture to support the application needs of the Computer Telephony (CT) industry, by providing CompactPCI system vendors and CT board vendors with specifications that will promote multi-vendor interoperability and support the design of open, standards based components and systems. These goals include provisions for intra-system isochronous (TDM) media transport, common telephony I/O definition, reliable hot swap of CT Front Boards and peripherals, as well as agencyaware safety recommendations.

PICMG 3.1 specification

PICMG 3.1 specification