storm部署（包括所有依赖rpm包、集群搭建详解）

1.修改主机名： vim /etc/sysconfig/network NETWORKING=yes HOSTNAME=MASTER 2.修改IP： vim /etc/sysconfig/network-scripts/ifcfg-eth0 BOOTPROTO="static" HWADDR="00:0C:29:FC:62:B6" IPV6INIT="yes" NM_CONTROLLED="yes" ONBOOT="yes" TYPE="Ethernet" UUID="d0731a46-36df-4ab1-9bac-42bb151acc41" IPADDR="192.168.1.250" NETMASK="255.255.255.0" GATEWAY="192.168.1.1" DNS1="8.8.8.8" DNS2="8.8.4.4" 3.修改主机和IP的映射关系 vim /etc/hosts 127.0.0.1 localhost localhost.localdomain localhost4 localhost4.localdomain4 ::1 localhost localhost.localdomain localhost6 localhost6.localdomain6 192.168.1.250 MASTER 192.168.1.251 SLAVE-1 192.168.1.252 SLAVE-2 4.关闭防火墙 vim /etc/sysconfig/selinux # This file controls the state of SELinux on the system. # SELINUX= can take one of these three values: # enforcing - SELinux security policy is enforced. # permissive - SELinux prints warnings instead of enforcing. # disabled - No SELinux policy is loaded. SELINUX=disabled # SELINUXTYPE= can take one of these two values: # targeted - Targeted processes are protected, # mls - Multi Level Security protection. SELINUXTYPE=targeted 继续执行命令： service iptables stop chkconfig iptables off reboot 5.上传jdk安装包 6.解压安装 chmod +x jdk-6u45-linux-x64.bin ./jdk-6u45-linux-x64.bin mkdir /usr/java mv jdk1.6.0_45/ /usr/java/ 7.配置环境变量 vim /etc/profile 在文件最后面添加： export JAVA_HOME=/usr/java/jdk1.6.0_45 export CLASSPATH=$JAVA_HOME/lib export PATH=$PATH:$JAVA_HOME/bin 更新配置： source /etc/profile 上传zeromq-2.1.7.tar.gz、jzmq-master.zip、storm-0.8.2.zip、zookeeper-3.4.5.tar.gz等文件 1.编译安装ZMQ： tar -xzf zeromq-2.1.7.tar.gz cd zeromq-2.1.7 ./configure #编译可能会出错：configure: error: Unable to find a working C++ compiler #安装一下依赖的rpm包：libstdc++-devel gcc-c++ 可以上网的情况下： yum install gcc-c++ 虚拟机不能上网情况：首先到http://mirrors.163.com/centos/6.4/os/x86_64/Packages/ 下载rpm rpm -i libstdc++-devel-4.4.7-3.el6.x86_64.rpm rpm -i gcc-c++-4.4.7-3.el6.x86_64.rpm rpm -i libuuid-devel-2.17.2-12.9.el6.x86_64.rpm ./configure make make install 2.编译安装JZMQ： cd jzmq ./autogen.sh #报错:autogen.sh: error: could not find libtool. libtool is required to run autogen.sh. 缺少libtool yum install libtool 或者手动安装 rpm -i autoconf-2.63-5.1.el6.noarch.rpm rpm -i automake-1.11.1-4.el6.noarch.rpm rpm -i libtool-2.2.6-15.5.el6.x86_64.rpm ./configure make make install