没有合适的资源?快使用搜索试试~ 我知道了~
卡尔蔡司DT16-80ZA镜头维修指南E文
4星 · 超过85%的资源 需积分: 32 7 下载量 54 浏览量
2010-06-05
17:18:40
上传
评论 1
收藏 2.39MB PDF 举报
温馨提示
试读
99页
从国外网站搜到的,内容详尽,绝对官方资料! 自拆镜头有风险,出手要谨慎!
资源推荐
资源详情
资源评论
SERVICE NOTE
SPECIFICATIONS
REPAIR PARTS LIST
DISASSEMBLY ADJUSTMENTS
SERVICE MANUAL
Link
Link
Revision History
Revision History
How to use
Acrobat Reader
How to use
Acrobat Reader
Sony EMCS Co.
SAL1680Z (Vario-Sonnar DT 3.5-4.5/16-80 ZA) (Vario-Sonnar T
*
DT 16-80mm F3.5-4.5 ZA)
Ver 1.0 2007.03
LENS FOR DSLR CAMERA
2007C0800-1
© 2007.03
Published by Kohda TEC9-852-120-11
US Model
Canadian Model
AEP Model
Chinese Model
SAL1680Z
(Vario-Sonnar DT 3.5-4.5/16-80 MA) (Vario-Sonnar T
*
DT 16-80mm F3.5-4.5 ZA)
• About the Lens Test Projector and Finished Inspection JIG
• About the Front Decoration Plate
— 2 —
SAL1680Z (Vario-Sonnar DT 3.5-4.5/16-80 ZA) (Vario-Sonnar T
*
DT 16-80mm F3.5-4.5 ZA)
SPECIFICATIONS
• This lens is equipped with a distance encoder. The distance encoder allows more accurate measurement (ADI) by using a flash for ADI.
• Depending on the lens mechanism, the focal length may change with any change of the shooting distance. The focal length assumes the lens is focused
at infinity.
Equivalent 35mm-format focal length
*
1
(mm)
24-120
*
1
The value for equivalent 35mm-format focal length is based on Digital Single Lens Reflex Cameras equipped with an APS-C sized image sensor.
Lens groups elements
10-14
Angle of view
*
2
83°-20°
*
2
The value of angle of view is based on Digital Single Lens Reflex Cameras equipped with an APS-C sized image sensor.
Minimum focus (m (feet))
*
3
0.35 (1.2)
*
3
Minimum focus is the shortest distance from the image sensor to the subject.
Maximum magnification (
××
××
×)
0.24
Minimum f-stop
f/22-29
Filter diameter (mm)
62
Dimensions (maximum diameter
××
××
× height) (mm (in.))
Approx. 72 × 83 (2 7/8 × 3 3/8)
Mass (g (oz.))
Approx. 445 (15 3/4)
Included items
Lens (1), Front lens cap (1), Rear lens cap (1), Lens hood (1), Lens case (1), Set of printed documentation
Designs and specifications are subject to change without notice.
— 3 —
SAL1680Z (Vario-Sonnar DT 3.5-4.5/16-80 ZA) (Vario-Sonnar T
*
DT 16-80mm F3.5-4.5 ZA)
TABLE OF CONTENTS
Section Title Page
1. SERVICE NOTE
1-1. Chemicals ·······································································1-1
1-2. Exterior Parts··································································1-1
1-3. Unleaded Solder ·····························································1-1
1-4. Safety Check-out ····························································1-2
1-5. Troubleshooting ·····························································1-3
2. DISASSEMBLY
2-1. Disassembly ···································································2-2
3. REPAIR PARTS LIST
3-1. Exploded Views ······························································3-1
3-2. Supplied Accessories······················································3-7
4. ADJUSTMENTS
4-1. Preparations····································································4-1
4-2. Aperture Diameter Check/adjustment ··························4-13
4-3. Projective Resolving Power Check/Adjustment ··········4-18
4-4. Flange Back (f’F) Check/Adjustment ··························4-22
4-5. Focus-Shift (by Zooming) Check/Adjustment ·············4-25
4-6. Focus Scale Plate, Position Adjustment ·······················4-27
4-7. Focus-shift Check/Adjustment (Aperture (Amount of
Spherical Aberration)) ··················································4-29
4-8. Toruqe Adjustment of MF Operation Ring ··················4-30
4-9. Lens ROM Check ·························································4-32
4-10. Zoom Brush Position Check/Adjustment and
Pattern Check ·······························································4-34
4-11. Focus Brush Position Check/Adjustment and
Pattern Check ·······························································4-42
4-12. Write dSB ·····································································4-50
1-1
SAL1680Z (Vario-Sonnar DT 3.5-4.5/16-80 ZA) (Vario-Sonnar T
*
DT 16-80mm F3.5-4.5 ZA)
1. SERVICE NOTE
1-1. Chemicals
Some chemicals used for servicing are highly volatile.
Their evaporation caused by improper management affects your health and environment, and wastes resources.
Manage the chemicals carefully as follows.
• Store chemicals sealed in a specific place to prevent from exposure to high temperature or direct sunlight.
• Avoid dividing chemicals into excessive numbers of small containers to reduce natural evaporation.
• Keep containers sealed to avoid natural evaporation when chemicals are not in use.
• Avoid using chemicals as much as possible. When using chemicals, divide only required amount to a small plate from the container and
use up it.
1-2. Exterior Parts
Be careful to the following points for exterior parts used in this unit.
• Use a piece of cleaning paper or cleaning cloth for cleaning exterior parts. Avoid using chemicals.
Even if you have to use chemicals to clean heavy dirt, don’t use paint thinner, ketone, nor alcohol.
• Insert the specific screws vertically to the part when installing a exterior part.
Be careful not to tighten screws too much.
1-3. Unleaded Solder
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead.
(
Caution: Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
• Set the soldering iron tip temperature to 350 °C approximately.
If cannot control temperature, solder/unsolder at high temperature for a short time.
Caution: The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Be sure to control soldering iron tips used for unleaded solder and those for leaded solder so they are managed separately. Mixing
unleaded solder and leaded solder will cause detachment phenomenon.
1-2
SAL1680Z (Vario-Sonnar DT 3.5-4.5/16-80 ZA) (Vario-Sonnar T
*
DT 16-80mm F3.5-4.5 ZA)
1-4. SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer.
1. Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and
bridges.
2. Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors.
3. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
4. Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their
replacement.
5. Check the B+ voltage to see it is at the values specified.
6. Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 °C during repairing.
• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or unsoldering.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
剩余98页未读,继续阅读
资源评论
- hadcom2013-08-08很好,有很大的帮助
wszcr
- 粉丝: 1
- 资源: 2
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功