Block Diagram (Continued)
Functional Description
The DS92LV1212 is a 10-bit Deserializer chip designed to
receive data over heavily loaded differential backplanes at
clock speeds from 16 MHz to 40 MHz. It may also be used to
receive data over Unshielded Twisted Pair (UTP) cable.
The chip has three active states of operation: Initialization,
Data Transfer, and Resynchronization; and two passive
states: Powerdown and TRI-STATE
®
.
The following sections describe each operation of the active
and passive states.
Initialization
Before data can be transferred, the Deserializer must be
initialized. The Deserializer should be powered up with the
PWRDN pin held low. After V
CC
stabilizes, the PWRDN pin
can be forced high. The Deserializer is ready to lock to the
incoming data stream.
Step 1: When you apply V
CC
to the Deserializer, the respec-
tive outputs are held in TRI-STATE and internal circuitry is
disabled by on-chip power-on circuitry. When V
CC
reaches
V
CC
OK (2.5V), the PLL is ready to lock to incoming data or
synchronization patterns. You must apply the local clock to
the REFCLK pin.
The Deserializer LOCK output will remain high while its PLL
locks to incoming data or to SYNC patterns on the inputs.
Step 2: The Deserializer PLL must synchronize to the Seri-
alizer to complete the initialization. The Deserializer will lock
to non-repetitive data patterns; however, the transmission of
SYNC patterns to the Deserializer enables the Deserializer
to lock to the Serializer signal within a specified time. See
Figure 7
.
The user’s application determines control of the SYNC1 and
SYNC2 pins. One recommendation is a direct feedback loop
from the LOCK pin. Under all circumstances, the Serializer
stops sending SYNC patterns after both SYNC inputs return
low.
When the Deserializer detects edge transitions at the Bus
LVDS input, it will attempt to lock to the embedded clock
information. When the Deserializer locks to the Bus LVDS
clock, the LOCK output will go low. When LOCK is low, the
Deserializer outputs represent incoming Bus LVDS data.
Data Transfer
After initialization, the Serializer will accept data from inputs
DIN0–DIN9. The Serializer uses the TCLK input to latch
incoming Data. The TCLK_R/F pin selects which edge the
Serializer uses to strobe incoming data. TCLK_R/F high
selects the rising edge for clocking data and low selects the
falling edge. If either of the SYNC inputs is high for 5*TCLK
cycles, the data at DIN0-DIN9 is ignored regardless of clock
edge.
After determining which clock edge to use, a start and stop
bit, appended internally, frame the data bits in the register.
The start bit is always high and the stop bit is always low.
The start and stop bits function as the embedded clock bits
in the serial stream.
Serialized data and clock bits (10+2 bits) are received at 12
times the TCLK frequency. For example, if TCLK is 40 MHz,
the serial rate is 40 x 12 = 480 Mega bits per second. Since
only 10 bits are from input data, the serial “payload” rate is
10 times the TCLK frequency. For instance, if TCLK = 40
MHz, the payload data rate is 40 x 10 = 400 Mbps. TCLK is
provided by the data source and must be in the range 16
MHz to 40 MHz nominal.
The LOCK pin on the Deserializer is driven low when it is
synchronized with the Serializer. The Deserializer locks to
the embedded clock and uses it to recover the serialized
data. ROUT data is valid when LOCK is low. Otherwise,
ROUT0–ROUT9 is invalid.
The ROUT0-ROUT9 pins use the RCLK pin as the reference
to data. The polarity of the RCLK edge is controlled by the
RCLK_R/F input. See
Figure 5
.
ROUT(0-9), LOCK and RCLK outputs will drive a minimum
of three CMOS input gates (15 pF load) with 40 MHz clock.
Resynchronization
When the Deserializer PLL locks to the embedded clock
edge, the Deserializer LOCK pin asserts a low. If the Dese-
rializer loses lock, the LOCK pin output will go high and the
outputs (including RCLK) will enter TRI-STATE.
The user’s system monitors the LOCK pin to detect a loss of
synchronization. Upon detection, the system can arrange to
pulse the Serializer SYNC1 or SYNC2 pin to resynchronize.
Multiple resynchronization approaches are possible. One
Application
DS101387-2
DS92LV1212A
www.national.com 2
5星 · 超过95%的资源 需积分: 0 147 浏览量
2023-02-08
23:23:18
上传
评论 4
收藏 406KB PDF 举报 
m0_745259962023-02-15#完美解决问题 #运行顺畅 #内容详尽 #全网独家 #注释完整
