没有合适的资源?快使用搜索试试~ 我知道了~
ASTM A510M.pdf
1.该资源内容由用户上传,如若侵权请联系客服进行举报
2.虚拟产品一经售出概不退款(资源遇到问题,请及时私信上传者)
2.虚拟产品一经售出概不退款(资源遇到问题,请及时私信上传者)
版权申诉
0 下载量 150 浏览量
2022-12-13
14:34:09
上传
评论
收藏 51KB PDF 举报
温馨提示
试读
7页
ASTM A510M.pdf
资源推荐
资源详情
资源评论
Designation: A 510M – 03
METRIC
Standard Specification for
General Requirements for Wire Rods and Coarse Round
Wire, Carbon Steel [Metric]
1
This standard is issued under the fixed designation A 510M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
1.1 This specification covers general requirements for car-
bon steel wire rods and uncoated coarse round wire in coils or
straightened and cut lengths.
1.2 In case of conflict, the requirements in the purchase
order, on the drawing, in the individual specification, and
in this general specification shall prevail in the sequence
named.
NOTE 1—This metric specification is equivalent to Specification A 510,
and is compatible in technical content.
2. Referenced Documents
2.1 ASTM Standards:
A 370 Test Methods and Definitions for Mechanical Testing
of Steel Products
2
A 700 Practices for Packaging, Marking, and Loading
Methods for Steel Products for Domestic Shipment
3
A 751 Test Methods, Practices, and Terminology for
Chemical Analysis of Steel Products
2
E 29 Practice for Using Significant Digits in Test Data to
Determine Conformance with Specifications
4
E 30 Test Methods for Chemical Analysis of Steel, Cast
Iron, Open-Hearth Iron, and Wrought Iron
5
E 112 Test Methods for Determining Average Grain Size
6
E 527 Practice for Numbering Metals and Alloys (UNS)
7
2.2 Society of Automotive Engineers Standard:
8
J 1086 Numbering Metals and Alloys
2.3 AIAG Standard:
AIAG B-5 02.00 Primary Metals Identification Tag Appli-
cation Standard
9
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 carbon steel—steel is considered to be carbon steel
when no minimum content is specified or required for alumi-
num, chromium, cobalt, columbium, molybdenum, nickel,
titanium, tungsten, vanadium, or zirconium, or any other
element added to obtain a desired alloying effect; when the
specified minimum for copper does not exceed 0.40 %; or
when the maximum content specified for any of the following
elements does not exceed these percentages: manganese 1.65,
silicon 0.60, or copper 0.60.
3.1.2 Discussion— In all carbon steels small quantities of
certain unspecified and unrequired residual elements (such as
copper, nickel, molybdenum, chromium, etc.) unavoidably
retained from raw materials are sometimes found. These
elements are considered as incidental and are not normally
determined or reported.
Elements (such as sulfur and lead) may be specified to
improve machinability of carbon steels.
3.1.3 coarse round wire—from 0.90 to 25 mm in diameter,
inclusive, wire produced from hot-rolled wire rods or hot-
rolled coiled rounds by one or more cold reductions primarily
for the purpose of obtaining a desired size with dimensional
accuracy, surface finish, and mechanical properties. By varying
the amount of cold reduction and other wire mill practices,
including thermal treatment, a wide diversity of mechanical
properties and finishes are made available. Suggested wire
diameters are shown in Table 1.
1
This specification is under the jurisdiction of ASTM Committee A1 on Steel,
Stainless Steel, and Related Alloys and is the direct responsibility of Subcommittee
A01.03 on Steel Rod and Wire.
Current edition approved Sept. 10, 2003. Published Sept. 2003. Originally
approved in 1977. Last previous edition approved in 2002 as A 510M – 02.
2
Annual Book of ASTM Standards, Vol 01.03.
3
Annual Book of ASTM Standards, Vol 01.05.
4
Annual Book of ASTM Standards, Vol 14.02.
5
Discontinued—See 1994 Annual Book of ASTM Standards, Vol 03.05.
6
Annual Book of ASTM Standards, Vol 03.01.
7
Annual Book of ASTM Standards, Vol 01.01.
8
Available from Society of Automotive Engineers (SAE), 400 Commonwealth
Dr., Warrendale, PA 15096-0001.
9
Available from Automotive Industry Action Group (AIAG), 26200 Lahser Rd.,
Suite 200, Southfield, MI 48034.
1
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
Copyright ASTM International
Provided by IHS under license with ASTM
Not for Resale
No reproduction or networking permitted without license from IHS
--`-`-`,,`,,`,`,,`---
资源评论
std86021
- 粉丝: 93
- 资源: 2610
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功