没有合适的资源?快使用搜索试试~ 我知道了~
BUFFALO巴法洛HD-WLU3_R1 系列参考手册.pdf
1.该资源内容由用户上传,如若侵权请联系客服进行举报
2.虚拟产品一经售出概不退款(资源遇到问题,请及时私信上传者)
2.虚拟产品一经售出概不退款(资源遇到问题,请及时私信上传者)
版权申诉
0 下载量 134 浏览量
2022-07-11
16:19:11
上传
评论
收藏 2.77MB PDF 举报
温馨提示
试读
45页
BUFFALO巴法洛HD-WLU3_R1 系列参考手册.pdf
资源推荐
资源详情
资源评论
Reference Guide
Troubleshooting ...........................................................4
RAID Mode Button ........................................................2
35011819 ver.01
2
Reference Guide
RAID Mode Button
The RAID mode can be changed by the RAID mode button located on the back of the DriveStation Duo.
Changing the RAID Mode
Caution
When the RAID mode is changed, all data stored in the DriveStation Duo is erased. If you
have important data saved, be sure to back up the data to a computer or other device be-
fore performing the procedure below.
1
Disconnect the DriveStation Duo from the computer.
2
Move the power switch to the OFF position, then set it to AUTO.
Wait for the power and access LEDs to turn o.
3
Hold down the RAID mode button for ve seconds.
The DriveStation Duo will beep.
4
Press the RAID mode button to cycle through the dierent RAID modes.
The current RAID mode is indicated by the colors of the access LEDs as shown below. If the
DriveStation Duo is in Windows XP compatibility mode, the access LEDs will blink. Each time the
RAID mode button is pressed, the RAID mode changes and the DriveStation Duo beeps.
RAID Mode Disk 1 Disk 2
Normal Green Red
RAID 0 Red Red
RAID 1 Green Green
Spanning Orange Orange
This is your last chance to abort! After the next step, you will be committed to changing
the RAID mode. To cancel changing the RAID mode, move the power switch to OFF now.
A table of LED colors for each RAID mode is also available on the back side of the front
cover.
Rear View
RAID mode button
3
Reference Guide
5
Hold down the RAID mode button for ve seconds.
The DriveStation Duo will beep once, the access LED turns o, and the power LED will blink
purple as the DriveStation Duo changes its RAID mode.
Caution
While the power LED is blinking purple, do not turn o the power or unplug your
DriveStation Duo. It could be damaged if power is lost during the RAID change.
6
When the change is complete, the DriveStation Duo will beep three times and
the power LED will stop blinking.
7
The access LEDs now show the new RAID mode.
8
Press the RAID mode button.
The DriveStation Duo will beep and shut down.
The RAID mode is now changed. Your new RAID array is not formatted yet, so connect the drive to
your computer and format it.
Checking the
RAID Mode
1
Disconnect the DriveStation Duo from the computer.
2
Move the power swich to the OFF position, then set it to AUTO.
Wait for the power and access LEDs to turn o.
3
Press the RAID mode button on the back side.
The DriveStation Duo will beep.
4
The power LED will turn purple and the current RAID mode is indicated by the
access LEDs.
The current RAID mode is indicated by the colors of the access LEDs as shown below. If the
DriveStation Duo is in Windows XP compatibility mode, the access LEDs will blink.
RAID Mode Disk 1 Disk 2
Normal Green Red
RAID 0 Red Red
RAID 1 Green Green
Spanning Orange Orange
A table of LED colors for each RAID mode is also available on the back side of the front
cover.
After conrmation is complete, press the RAID mode button.
The DriveStation Duo will beep and shut down.
4
Reference Guide
Troubleshooting
The DriveStation Duo indicates errors with beeps and LED ashes. These beeps and ashes can help you
troubleshoot problems.
Access LED Status Beeping DriveStation Duo Status
ー
Repeated beeps
The fan on the back side is stopped. Turn off the
DriveStation Duo and check if dust has accumulated on
the fan. If removing dust does not solve the problem,
the fan may be broken. Contact the Buffalo Technology
Support Center.
ー
One long,
continuous beep
A hard drive has overheated. Check if the fan on the back
side is running.
If the fan is not running, turn off the DriveStation Duo
and check if dust has accumulated on the fan. If the fan
still does not run after removing dust, it may be broken.
Contact the Bualo Technology Support Center.
If it is running, the hard drive may have failed. Check the
access LED to conrm the hard drive status. A hard drive
still may have overheated even if no access LED for either
hard drive is lit red. Turn o the power, and wait at least
one hour before using again.
One access LED is
glowing red
Beeps for about
three seconds and
stops
An error occurred in the hard drive. Replace the hard drive
whose access LED is lit. If replacing the hard drive does not
solve the problem, check if the hard drive is connected
correctly.
Access LEDs
These indicate the status of the built-in
hard drives. The top LED indicates the
status for Disk 1 and the bottom LED
indicates the status for Disk 2.
Power LED
This is lit when the power is turned
on and during RAID maintenance.
Go to Next Page
Beep
5
Reference Guide
One or both of
the access LEDs is
blinking red
(Short beeps)
A rebuild is in progress. Normally this happens after a
hard drive is replaced in RAID 1 mode. Do not turn o the
power until rebuilding is complete. When rebuilding is
complete, the unit will beep three times and the access
LED will glow a steady green (not blinking). During
the rebuild, turning o the power can damage the unit or
corrupt data.
During the rebuild, you may be able to continue to use the
DriveStation Duo normally, but data transfers will be slower.
In RAID 1 mode with no computer connected, the
rebuilding process takes about 45 minutes per 100 GB. The
DriveStation Duo will take about 7 hours and 20 minutes to
rebuild. These times are estimated.
Both access LEDs
are glowing red
Beep for about
three seconds and
stops
The DriveStation Duo is not recognized. Check the USB
cable connecting the DriveStation Duo to your computer.
An access LED is
completely o
-
The hard drive is not connected correctly. Make sure that
the drives are rmly seated inside the DriveStation Duo.
The corresponding access LED blinks green when a drive is being accessed. During RAID maintenance,
the power LED glows purple.
剩余44页未读,继续阅读
资源评论
qingguo1979
- 粉丝: 28
- 资源: 7296
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功