i
I
r
...,
.\
!:
:
I'i
INTERNATIONAL
rso/rEc
STANDARD
First
edition
2001-02-01
AMENDMENT
1
2005-06-0
1
ldentification
cards
-
Contactless
integrated circuit(s)
cards
-
Proximity
cards
-
Part
3:
Initialization and anticollision
-
AMENDMENT
1:
Bit rates
of
fcl64, fcl32
and
fcl16
Cartes d'identification
-
Cartes
a circuit(s)
integre(s) sans
contact
-
Carfes de
proximite
-
Partie 3:
lnitialisation et anticollision
AMENDEMENT
1: Debits binaires
de
fc/64, fc/32 et
fc/16
Reference
number
ISO/l EC 1
4443-3.2001/Amd.
1
:2005(E)
14443-3
@E
o
tso/tEC
2005
ISO/IEC
1 4443-3:2001
/Am d.
1 :2005(E)
PDF disclaimer
This
PDF file may contain embedded
typefaces.
In accordance
with Adobe's
licensing
policy,
this file may be
printed
or
viewed but
shall
not be edited unless
the typefaces
which are embedded
are
licensed lo and
installed on
the
computer
performing
the editing.
In
downloading
this file,
parties
accept
therein the responsibility of
not infringing
Adobe's licensing
policy.
The ISO
Central Secretariat
accepts
no liability
in this
area.
Adobe is a
trademark of
Adobe
Systems
Incorporated.
Details
of the software
products
used to create
this PDF file can be
found
in the General
Info relative
to the file;
the PDF-creation
parameters
were
optimized
for
printing.
Every care
has been
taken to ensure
that the file
is
suitable
for use
by ISO
member bodies.
In
the unlikely event
that a
problem
relating
to it is found,
please
inform
the
Central
Secretariat
at
the
address
given below.
@ tso/rEc
2005
All
rights
reserved. Unless otherwise
specified,
no
part
of this
publication
may be
reproduced or
utilized
in any
form or by any
means'
electronic or
mechanical,
including
photocopying
and
microfilm,
without
permission in writing
from either
ISO
at the address
below
or
ISO's member
body
in the country
of the
requester.
ISO copyright
office
Case
postale
56
.
CH-121
1
Geneva
20
Tel.
+41
2274901
11
Fax
+41227490947
E-mail
copyright@iso.org
Web
www.iso.org
Published in Switzerland
O
ISO/lEC
2005
-
All rights
reserved
ISO/IEC
1
4443-3:2001
/Amd.
1 : 2005(
E)
Foreword
ISO
(the
International
Organization
for Standardization)
and
IEC
(the International
Electrotechnical
Commission)
form the
specillized
system
for
worldwide
standardization.
National
bodies
that are
members
of
ISO or
lEi
participate in the
development
of
International
Standards
through
technical
committees
established
by
the
respective
organization
to
deal
with
particular fields
of technical
activity'
ISO and
IEC
technical
committees
collaborate
ln fields
of
mutual
interest.
Other
international
organizations,
governmental
and
non-governmental,
in liaison
with
ISO and
lEC,
also
take
part
in the
work.
In the
field
of
information
technology,
ISO and
IEC
have
established
a
joint
technical
committee,
ISO/IEC
JTC
1.
lnternational
Standards
are
drafted
in accordance
with the
rules
given in
the
ISO/lEC
Directives'Part2'
The
main task
of the
joint
technical
committee
is to
prepare
International
Standards.
Draft
International
Standards
adopted
by the
joint
technical
committee
are
circulated
to
national
bodies
for
voting.
Publication
as
an International
Standard
requires
approval
by
at
least
75% of
the
national
bodies
casting
a
vote.
Attention
is drawn
to the
possibility that some
of the
elements
of this
document
may be
the
subject
of
patent
rights.
ISO and
IEC
shall
not be
held
responsible
for identifying
any
or all
such
patent rights.
Amendment
1
to lSOilEC
14443-3:2001
was
prepared by
Joint
Technical
Committee
ISO/IEC
JTC
1'
lnformation
technology,
Subcommittee
SC
17, Cards
and
personal
identification.
O
ISO/lEC
2005
-
All
rights reserved
ISO/IEC
1 4443-3:2001 /Amd.
1 :2005(E)
ldentification cards
-
Gontactless
integrated circuit(s)
cards
-
Proximity cards
-
Part
3:
lnitialization and
anticollision
AMENDMENT
1: Bit
rates of fcl64.
fcl32 and
fcl16
Page 2, term
number 3.5
Replace
the
existing definition
with the
following:
"elementary
time
unit
etu
time
unit calculated by
the following
formula:
letu=1281(Dxtc)
where
D e
{1,2,4,8}
fc is
the
carrier
frequency as defined
in ISO/IEC 14443-2.
The initial
value of the divisor
D is 1,
giving
the
initial
etu as
follows:
1
etu
=
128 lfc.
Page
3, Clause
4
Add the following
new abbreviations.
"D
Divisor
TR2 Frame delay
Time PICC to
PCD, Type
B"
Page 5, Clause
5
Replace
the
existing
Clause
5 title with the following:
5
Alternating between
Type A and
Type B
commands,
5.1 Polling
O ISO/IEC
2005
-
All rights reserved
