MTRR (Memory Type Range Register) control
3 Jun 1999
Richard Gooch
<rgooch@atnf.csiro.au>
On Intel P6 family processors (Pentium Pro, Pentium II and later)
the Memory Type Range Registers (MTRRs) may be used to control
processor access to memory ranges. This is most useful when you have
a video (VGA) card on a PCI or AGP bus. Enabling write-combining
allows bus write transfers to be combined into a larger transfer
before bursting over the PCI/AGP bus. This can increase performance
of image write operations 2.5 times or more.
The Cyrix 6x86, 6x86MX and M II processors have Address Range
Registers (ARRs) which provide a similar functionality to MTRRs. For
these, the ARRs are used to emulate the MTRRs.
The AMD K6-2 (stepping 8 and above) and K6-3 processors have two
MTRRs. These are supported. The AMD Athlon family provide 8 Intel
style MTRRs.
The Centaur C6 (WinChip) has 8 MCRs, allowing write-combining. These
are supported.
The VIA Cyrix III and VIA C3 CPUs offer 8 Intel style MTRRs.
The CONFIG_MTRR option creates a /proc/mtrr file which may be used
to manipulate your MTRRs. Typically the X server should use
this. This should have a reasonably generic interface so that
similar control registers on other processors can be easily
supported.
There are two interfaces to /proc/mtrr: one is an ASCII interface
which allows you to read and write. The other is an ioctl()
interface. The ASCII interface is meant for administration. The
ioctl() interface is meant for C programs (i.e. the X server). The
interfaces are described below, with sample commands and C code.
===============================================================================
Reading MTRRs from the shell:
% cat /proc/mtrr
reg00: base=0x00000000 ( 0MB), size= 128MB: write-back, count=1
reg01: base=0x08000000 ( 128MB), size= 64MB: write-back, count=1
===============================================================================
Creating MTRRs from the C-shell:
# echo "base=0xf8000000 size=0x400000 type=write-combining" >! /proc/mtrr
or if you use bash:
# echo "base=0xf8000000 size=0x400000 type=write-combining" >| /proc/mtrr
And the result thereof:
% cat /proc/mtrr
reg00: base=0x00000000 ( 0MB), size= 128MB: write-back, count=1
reg01: base=0x08000000 ( 128MB), size= 64MB: write-back, count=1
reg02: base=0xf8000000 (3968MB), size= 4MB: write-combining, count=1
This is for video RAM at base address 0xf8000000 and size 4 megabytes. To
find out your base address, you need to look at the output of your X
server, which tells you where the linear framebuffer address is. A
typical line that you may get is:
(--) S3: PCI: 968 rev 0, Linear FB @ 0xf8000000
Note that you should only use the value from the X server, as it may
move the framebuffer base address, so the only value you can trust is
that reported by the X server.
To find out the size of your framebuffer (what, you don't actually
know?), the following line will tell you:
(--) S3: videoram: 4096k
That's 4 megabytes, which is 0x400000 bytes (in hexadecimal).
A patch is being written for XFree86 which will make this automatic:
in other words the X server will manipulate /proc/mtrr using the
ioctl() interface, so users won't have to do anything. If you use a
commercial X server, lobby your vendor to add support for MTRRs.
===============================================================================
Creating overlapping MTRRs:
%echo "base=0xfb000000 size=0x1000000 type=write-combining" >/proc/mtrr
%echo "base=0xfb000000 size=0x1000 type=uncachable" >/proc/mtrr
And the results: cat /proc/mtrr
reg00: base=0x00000000 ( 0MB), size= 64MB: write-back, count=1
reg01: base=0xfb000000 (4016MB), size= 16MB: write-combining, count=1
reg02: base=0xfb000000 (4016MB), size= 4kB: uncachable, count=1
Some cards (especially Voodoo Graphics boards) need this 4 kB area
excluded from the beginning of the region because it is used for
registers.
NOTE: You can only create type=uncachable region, if the first
region that you created is type=write-combining.
===============================================================================
Removing MTRRs from the C-shell:
% echo "disable=2" >! /proc/mtrr
or using bash:
% echo "disable=2" >| /proc/mtrr
===============================================================================
Reading MTRRs from a C program using ioctl()'s:
/* mtrr-show.c
Source file for mtrr-show (example program to show MTRRs using ioctl()'s)
Copyright (C) 1997-1998 Richard Gooch
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
Richard Gooch may be reached by email at rgooch@atnf.csiro.au
The postal address is:
Richard Gooch, c/o ATNF, P. O. Box 76, Epping, N.S.W., 2121, Australia.
*/
/*
This program will use an ioctl() on /proc/mtrr to show the current MTRR
settings. This is an alternative to reading /proc/mtrr.
Written by Richard Gooch 17-DEC-1997
Last updated by Richard Gooch 2-MAY-1998
*/
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <sys/ioctl.h>
#include <errno.h>
#include <asm/mtrr.h>
#define TRUE 1
#define FALSE 0
#define ERRSTRING strerror (errno)
static char *mtrr_strings[MTRR_NUM_TYPES] =
{
"uncachable", /* 0 */
"write-combining", /* 1 */
"?", /* 2 */
"?", /* 3 */
"write-through", /* 4 */
"write-protect", /* 5 */
"write-back", /* 6 */
};
int main ()
{
int fd;
struct mtrr_gentry gentry;
if ( ( fd = open ("/proc/mtrr", O_RDONLY, 0) ) == -1 )
{
if (errno == ENOENT)
{
fputs ("/proc/mtrr not found: not supported or you don't have a PPro?\n",
stderr);
exit (1);
}
fprintf (stderr, "Error opening /proc/mtrr\t%s\n", ERRSTRING);
exit (2);
}
for (gentry.regnum = 0; ioctl (fd, MTRRIOC_GET_ENTRY, &gentry) == 0;
++gentry.regnum)
{
if (gentry.size < 1)
{
fprintf (stderr, "Register: %u disabled\n", gentry.regnum);
continue;
}
fprintf (stderr, "Register: %u base: 0x%lx size: 0x%lx type: %s\n",
gentry.regnum, gentry.base, gentry.size,
mtrr_strings[gentry.type]);
}
if (errno == EINVAL) exit (0);
fprintf (stderr, "Error doing ioctl(2) on /dev/mtrr\t%s\n", ERRSTRING);
exit (3);
} /* End Function main */
===============================================================================
Creating MTRRs from a C programme using ioctl()'s:
/* mtrr-add.c
Source file for mtrr-add (example programme to add an MTRRs using ioctl())
Copyright (C) 1997-1998 Richard Gooch
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; either version 2 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program; if not, writ
没有合适的资源?快使用搜索试试~ 我知道了~
mtrr.rar_V2
共3个文件
c:2个
txt:1个
1.该资源内容由用户上传,如若侵权请联系客服进行举报
2.虚拟产品一经售出概不退款(资源遇到问题,请及时私信上传者)
2.虚拟产品一经售出概不退款(资源遇到问题,请及时私信上传者)
版权申诉
0 下载量 72 浏览量
2022-09-14
22:24:24
上传
评论
收藏 7KB RAR 举报
温馨提示
library functions for processor-specific routines for Linux v2.13.6.
资源推荐
资源详情
资源评论
收起资源包目录
mtrr.rar (3个子文件)
mtrr.txt 10KB
mtrr.c 2KB
copy_user.c 10KB
共 3 条
- 1
资源评论
局外狗
- 粉丝: 67
- 资源: 1万+
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功