/**
@page NVIC_DMA_WFIMode NVIC_DMA_WFIMode
@verbatim
******************** (C) COPYRIGHT 2010 STMicroelectronics *******************
* @file NVIC/DMA_WFIMode/readme.txt
* @author MCD Application Team
* @version V3.3.0
* @date 04/16/2010
* @brief Description of the NVIC DMA in WFI mode Example.
******************************************************************************
* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
* TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
* DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
* FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
* CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
******************************************************************************
@endverbatim
@par Example Description
This example shows how to enters the system to WFI mode with DMA transfer enabled
and wake-up from this mode by the DMA End of Transfer interrupt.
In the associated software, the system clock is set to 72 MHz (24MHz on Value line),
the DMA1 Channely is configured to transfer 10 data from the EVAL COM1 USART data
register to a predefined buffer, DST_Buffer, and to generate an interrupt at the
end of the transfer.
The EVAL COM1 USART receives data from Hyperterminal.
A LED1 is toggled with a frequency depending on the system clock, this is used
to indicate whether the MCU is in WFI or RUN mode.
A falling edge on the selected EXTI Line will put the core in the WFI mode,
causing the led pin to stop toggling.
To wake-up from WFI mode you have to send the sequence (0, 1, 2, 3, 4, 5, 6, 7, 8, 9)
from the Hyperterminal to the EVAL COM1 USART. These bytes will be transferred
by the DMA from the EVAL COM1 receive data register to the predefined buffer,
then generates an interrupt which exits the system from WFI mode.
The LED1 restarts toggling and a LED2 will toggle if the buffer is correctly
received else a LED3 is toggled.
@par Directory contents
- NVIC/DMA_WFIMode/stm32f10x_conf.h Library Configuration file
- NVIC/DMA_WFIMode/stm32f10x_it.c Interrupt handlers
- NVIC/DMA_WFIMode/stm32f10x_it.h Interrupt handlers header file
- NVIC/DMA_WFIMode/main.c Main program
@par Hardware and Software environment
- This example runs on STM32F10x Connectivity line, High-Density, Medium-Density,
XL-Density, Medium-Density Value line, Low-Density and Low-Density Value line Devices.
- This example has been tested with STMicroelectronics STM32100B-EVAL (Medium-Density
Value line), STM3210C-EVAL (Connectivity line), STM3210E-EVAL (High-Density and
XL-Density) and STM3210B-EVAL (Medium-Density) evaluation boards and can be easily
tailored to any other supported device and development board.
To select the STMicroelectronics evaluation board used to run the example,
uncomment the corresponding line in stm32_eval.h file (under Utilities\STM32_EVAL)
- STM32100B-EVAL Set-up
- Use LED1, LED2, LED3 and LED4 leds connected respectively to PC.06, PC.07, PC.08
and PC.09 pins
- The USART1 signals (Rx, Tx) must be connected to a DB9 connector using a RS232
transceiver.
- Connect a null-modem female/female RS232 cable between the DB9 connector,
CN10 on STM32100B-EVAL board, and PC serial port.
- Hyperterminal configuration:
- Word Length = 8 Bits
- One Stop Bit
- No parity
- BaudRate = 115200 baud
- flow control: None
- Use the Key push-button connected to pin PB.09 (EXTI Line9).
- STM3210C-EVAL Set-up
- Use LED1, LED2, LED3 and LED4 connected respectively to PD.07, PD.13, PF.03
and PD.04 pins
- The USART2 signals (Rx, Tx) must be connected to a DB9 connector using a RS232
transceiver.
- Connect a null-modem female/female RS232 cable between the DB9 connector,
CN6 on STM3210C-EVAL board, and PC serial port.
- Hyperterminal configuration:
- Word Length = 8 Bits
- One Stop Bit
- No parity
- BaudRate = 115200 baud
- flow control: None
- Use the Key push-button connected to pin PB.09 (EXTI Line9).
- STM3210E-EVAL Set-up
- Use LED1, LED2, LED3 and LED4 leds connected respectively to PF.06, PF0.7, PF.08
and PF.09 pins
- The USART1 signals (Rx, Tx) must be connected to a DB9 connector using a RS232
transceiver.
- Connect a null-modem female/female RS232 cable between the DB9 connector,
CN12 on STM3210E-EVAL board, and PC serial port.
- Hyperterminal configuration:
- Word Length = 8 Bits
- One Stop Bit
- No parity
- BaudRate = 115200 baud
- flow control: None
- Use the Key push-button connected to pin PG.08 (EXTI Line8).
- STM3210B-EVAL Set-up
- Use LED1, LED2, LED3 and LED4 leds connected respectively to PC.06, PC.07, PC.08
and PC.09 pins
- The USART1 signals (Rx, Tx) must be connected to a DB9 connector using a RS232
transceiver.
- Connect a null-modem female/female RS232 cable between the DB9 connector,
CN6 on STM3210B-EVAL board, and PC serial port.
- Hyperterminal configuration:
- Word Length = 8 Bits
- One Stop Bit
- No parity
- BaudRate = 115200 baud
- flow control: None
- Use the Key push-button connected to pin PB.09 (EXTI Line9).
@par How to use it ?
In order to make the program work, you must do the following :
- Create a project and setup all project configuration
- Add the required Library files :
- stm32f10x_exti.c
- stm32f10x_gpio.c
- stm32f10x_rcc.c
- stm32f10x_dma.c
- stm32f10x_usart.c
- stm32f10x_i2c.c
- stm32f10x_spi.c
- misc.c
- system_stm32f10x.c (under Libraries\CMSIS\CM3\DeviceSupport\ST\STM32F10x)
- stm32_eval.c (under Utilities\STM32_EVAL)
- Edit stm32f10x.h file to select the device you are working on.
- Edit stm32_eval.h file to select the evaluation board you will use.
@b Tip: You can tailor the provided project template to run this example, for
more details please refer to "stm32f10x_stdperiph_lib_um.chm" user
manual; select "Peripheral Examples" then follow the instructions
provided in "How to proceed" section.
- Link all compiled files and load your image into target memory
- Run the example
@note
- Low-density Value line devices are STM32F100xx microcontrollers where the
Flash memory density ranges between 16 and 32 Kbytes.
- Low-density devices are STM32F101xx, STM32F102xx and STM32F103xx
microcontrollers where the Flash memory density ranges between 16 and 32 Kbytes.
- Medium-density Value line devices are STM32F100xx microcontrollers where
the Flash memory density ranges between 64 and 128 Kbytes.
- Medium-density devices are STM32F101xx, STM32F102xx and STM32F103xx
microcontrollers where the Flash memory density ranges between 64 and 128 Kbytes.
- High-density devices are STM32F101xx and STM32F103xx microcontrollers where
the Flash memory density ranges between 256 and 512 Kbytes.
- XL-density devices are STM32F101xx and STM32F103xx microcontrollers where
the Flash memory density ranges between 512 and 1024 Kbytes.
- Connectivity line devices are STM32F105xx and STM32F107xx microcontrollers.
* <h3><center>© COPYRIGHT 2010 STMicroelectronics</center></h3>
*/
STM32_ADC.rar_stm32 adc
版权申诉
125 浏览量
2022-09-23
00:19:06
上传
评论
收藏 5.11MB RAR 举报
STM32_ADC.rar_stm32 adc （911个子文件） 
cstart_thumb2.asm 4KB cstart_thumb2.asm 4KB cstart_thumb2.asm 4KB cstart_thumb2.asm 4KB cstart_thumb2.asm 4KB cstart_thumb2.asm 4KB cstart_thumb2.asm 4KB setstack.asm 66B setstack.asm 66B setstack.asm 66B Output.axf 382KB Project_uvproj.bak 222KB Project_uvopt.bak 186KB Project.cspy.bat 2KB
logo.bmp 7KB stm32f10x_tim.c 105KB stm32_eval_sdio_sd.c 90KB stm32f10x_flash.c 62KB stm3210c_eval_lcd.c 57KB stm32100b_eval_lcd.c 54KB stm3210b_eval_lcd.c 54KB stm32f10x_rcc.c 50KB stm32100b_eval_cec.c 48KB fonts.c 46KB stm32f10x_adc.c 46KB stm32f10x_i2c.c 43KB stm3210e_eval_lcd.c 40KB stm32f10x_usart.c 37KB stm32f10x_fsmc.c 34KB system_stm32f10x.c 31KB system_stm32f10x.c 31KB system_stm32f10x.c 31KB system_stm32f10x.c 31KB system_stm32f10x.c 31KB system_stm32f10x.c 31KB system_stm32f10x.c 31KB stm32f10x_can.c 31KB stm32f10x_spi.c 29KB stm32f10x_sdio.c 28KB stm32f10x_dma.c 27KB stm32_eval_spi_sd.c 25KB stm32_eval_i2c_ee.c 23KB stm3210e_eval.c 22KB stm3210c_eval.c 21KB stm32100b_eval.c 21KB stm3210b_eval.c 21KB stm32_eval_i2c_tsensor.c 19KB stm32f10x_gpio.c 19KB main.c 19KB stm32f10x_dac.c 19KB spi_flash.c 18KB stm3210e_eval_fsmc_nand.c 18KB core_cm3.c 17KB stm32_eval_spi_flash.c 16KB main.c 15KB stm3210e_eval_fsmc_nor.c 14KB main.c 13KB main.c 12KB main.c 12KB stm32f10x_cec.c 11KB main.c 11KB main.c 11KB main.c 11KB main.c 11KB main.c 10KB main.c 10KB main.c 10KB lib_dbg.c 10KB main.c 10KB main.c 10KB main.c 10KB main.c 10KB main.c 9KB main.c 9KB main.c 9KB main.c 9KB main.c 9KB main.c 9KB main.c 9KB stm32f10x_pwr.c 9KB stm32f10x_it.c 9KB stm32f10x_it.c 9KB main.c 9KB main.c 9KB main.c 9KB main.c 9KB main.c 9KB main.c 9KB stm32f10x_rtc.c 8KB main.c 8KB stm32f10x_bkp.c 8KB main.c 8KB main.c 8KB main.c 8KB main.c 8KB stm32f10x_it.c 8KB main.c 8KB main.c 8KB main.c 8KB main.c 8KB共 911 条
- 1
- 2
- 3
- 4
- 5
- 6
- 10
资源评论
