IIC.rar_ARM9 IIC_arm9 程序_iic测试指标_s3c2440 iic_s3c2440通讯

//==================================================================== // 文件名 : IIC.c // 功 能 : S3C2440 IIC-bus Master Tx/Rx mode Test Program // (Interrupt / Non Interrupt (Polling)) // 维护记录: 2009-8-26 V1.0 by xgc //==================================================================== #include <string.h> #include "2440addr.h" #include "2440lib.h" #include "def.h" #include "IIC.h" #include "uart.h" static U8 _iicData[IICBUFSIZE]; static volatile int _iicDataCount; static volatile int _iicStatus; static volatile int _iicMode; static int _iicPt; //******************[ Test_Iic ]************************************** void Test_Iic(void) { unsigned int i,j,save_E,save_PE; static U8 data[256]; Uart_Printf("[ IIC Test(Interrupt) using AT24C04 ]\n"); save_E = rGPECON; save_PE = rGPEUP; rGPEUP |= 0xc000; //Pull-up disable rGPECON |= 0xa0000000; //GPE15:IICSDA , GPE14:IICSCL pISR_IIC = (unsigned)IicInt; rINTMSK &= ~(BIT_IIC); //Enable ACK, Prescaler IICCLK=PCLK/16, Enable interrupt, Transmit clock value Tx clock=IICCLK/16 // If PCLK 50.7MHz, IICCLK = 3.17MHz, Tx Clock = 0.198MHz rIICCON = (1<<7) | (0<<6) | (1<<5) | (0xf); rIICADD = 0x10; //2440 slave address = [7:1] rIICSTAT = 0x10; //IIC bus data output enable(Rx/Tx) rIICLC = (1<<2)|(1); // Filter enable, 15 clocks SDA output delay added by junon Uart_Printf("Write test data into AT24C04\n"); for(i=0;i<256;i++) Wr24C04(0xa0,(U8)i,i); for(i=0;i<256;i++) data[i] = 0; Uart_Printf("Read test data from AT24C04\n"); for(i=0;i<256;i++) Rd24C04(0xa0,(U8)i,&(data[i])); //Line changed 0 ~ f for(i=0;i<16;i++) { for(j=0;j<16;j++) Uart_Printf("%2x ",data[i*16+j]); Uart_Printf("\n"); } rINTMSK |= BIT_IIC; rGPEUP = save_PE; rGPECON = save_E; } //*************************[ Wr24C04 ]**************************** void Wr24C04(U32 slvAddr,U32 addr,U8 data) { _iicMode = WRDATA; _iicPt = 0; _iicData[0] = (U8)addr; _iicData[1] = data; _iicDataCount = 2; rIICDS = slvAddr; //0xa0 rIICSTAT = 0xf0; //MasTx,Start //Clearing the pending bit isn't needed because the pending bit has been cleared. while(_iicDataCount!=-1); _iicMode = POLLACK; while(1) { rIICDS = slvAddr; _iicStatus = 0x100; rIICSTAT = 0xf0; //MasTx,Start rIICCON = 0xaf; //Resumes IIC operation. while(_iicStatus==0x100); if(!(_iicStatus&0x1)) break; //When ACK is received } rIICSTAT = 0xd0; //Stop MasTx condition rIICCON = 0xaf; //Resumes IIC operation. Delay(1); //Wait until stop condtion is in effect. //Write is completed. } //**********************[ Rd24C04 ] *********************************** void Rd24C04(U32 slvAddr,U32 addr,U8 *data) { _iicMode = SETRDADDR; _iicPt = 0; _iicData[0] = (U8)addr; _iicDataCount = 1; rIICDS = slvAddr; rIICSTAT = 0xf0; //MasTx,Start //Clearing the pending bit isn't needed because the pending bit has been cleared. while(_iicDataCount!=-1); _iicMode = RDDATA; _iicPt = 0; _iicDataCount = 1; rIICDS = slvAddr; rIICSTAT = 0xb0; //MasRx,Start rIICCON = 0xaf; //Resumes IIC operation. while(_iicDataCount!=-1); *data = _iicData[1]; } //------------------------------------------------------------------------- void __irq IicInt(void) { U32 iicSt,i; rSRCPND = BIT_IIC; //Clear pending bit rINTPND = BIT_IIC; iicSt = rIICSTAT; if(iicSt & 0x8){} //When bus arbitration is failed. if(iicSt & 0x4){} //When a slave address is matched with IICADD if(iicSt & 0x2){} //When a slave address is 0000000b if(iicSt & 0x1){} //When ACK isn't received switch(_iicMode) { case POLLACK: _iicStatus = iicSt; break; case RDDATA: if((_iicDataCount--)==0) { _iicData[_iicPt++] = rIICDS; rIICSTAT = 0x90; //Stop MasRx condition rIICCON = 0xaf; //Resumes IIC operation. Delay(1); //Wait until stop condtion is in effect. //Too long time... //The pending bit will not be set after issuing stop condition. break; } _iicData[_iicPt++] = rIICDS; //The last data has to be read with no ack. if((_iicDataCount)==0) rIICCON = 0x2f; //Resumes IIC operation with NOACK. else rIICCON = 0xaf; //Resumes IIC operation with ACK break; case WRDATA: if((_iicDataCount--)==0) { rIICSTAT = 0xd0; //Stop MasTx condition rIICCON = 0xaf; //Resumes IIC operation. Delay(1); //Wait until stop condtion is in effect. //The pending bit will not be set after issuing stop condition. break; } rIICDS = _iicData[_iicPt++]; //_iicData[0] has dummy. for(i=0;i<10;i++); //for setup time until rising edge of IICSCL rIICCON = 0xaf; //resumes IIC operation. break; case SETRDADDR: // Uart_Printf("[ S%d ]",_iicDataCount); if((_iicDataCount--)==0) break; //IIC operation is stopped because of IICCON[4] rIICDS = _iicData[_iicPt++]; for(i=0;i<10;i++); //For setup time until rising edge of IICSCL rIICCON = 0xaf; //Resumes IIC operation. break; default: break; } } //*********************[ Test_Iic2 ]********************************* void Test_Iic2(void) { unsigned int i,j,save_E,save_PE; static U8 data[256]; Uart_Printf("[ IIC Test(Polling) using AT24C04 ]\n"); save_E = rGPECON; save_PE = rGPEUP; rGPEUP |= 0xc000; //Pull-up disable rGPECON |= 0xa0000000; //GPE15:IICSDA , GPE14:IICSCL //Enable ACK, Prescaler IICCLK=PCLK/16, Enable interrupt, Transmit clock value Tx clock=IICCLK/16 rIICCON = (1<<7) | (0<<6) | (1<<5) | (0xf); rIICADD = 0x10; //2440 slave address = [7:1] rIICSTAT = 0x10; //IIC bus data output enable(Rx/Tx) //rIICLC = (1<<2)|(3); // Filter enable, 15 clocks SDA output delay added by junon Uart_Printf("Write test data into AT24C04\n"); for(i=0;i<256;i++) _Wr24C04(0xa0,(U8)i,255-i); for(i=0;i<256;i++) data[i] = 0; Uart_Printf("Read test data from AT24C04\n"); for(i=0;i<256;i++) _Rd24C04(0xa0,(U8)i,&(data[i])); for(i=0;i<16;i++) { for(j=0;j<16;j++) Uart_Printf("%2x ",data[i*16+j]); Uart_Printf("\n"); } rGPEUP