实验9DS1302实时时钟设计实验程序.rar_DS1302实时时钟设计实验程序

共38个文件

bak：5个

ds1302：2个

plg：2个

版权申诉

190 浏览量 2022-09-21 00:30:14 上传评论收藏 4.1MB RAR 举报

资源推荐

资源详情

资源评论

收起资源包目录

实验9 DS1302实时时钟设计实验程序.rar （38个子文件）

实验9 DS1302实时时钟设计实验程序

1个C程序

ds1302.OBJ 22KB

ds1302.Opt 819B

Last Loaded ds1302.DBK 90KB

Text1.c 9KB

ds1302.M51 25KB

ds1302.lnp 44B

ds1302.hex 7KB

ds1302.Uv2 2KB

ds1302.DSN 90KB

ds1302_Opt.Bak 817B

ds1302.PWI 909B

ds1302.c 12KB

ds1302_Uv2.Bak 2KB

ds1302 17KB

ds1302.plg 0B

ds1302.LST 21KB

DS1302中文资料.docx 1.51MB

STC12C5A60S2.pdf 2.34MB

2016级实验9报告纸电子版.doc 75KB

1个汇编程序

实验9程序.obj 9KB

DS1302_Opt.Bak 1KB

DS1302.lnp 49B

实验9程序.ASM 29KB

Last Loaded ds1302.DBK 94KB

DS1302_Uv2.Bak 2KB

DS1302.plg 0B

DS1302.hex 5KB

DS1302.Opt 1KB

DS1302 8KB

DS13022 8KB

DS1302.M51 38KB

实验9程序.LST 70KB

ds1302.DSN 94KB

ds1302.PWI 909B

实验9程序.BAK 16KB

DS1302.Uv2 2KB

DS1302.pdf 213KB

~$1302中文资料.docx 162B

1 of 15 092801

FEATURES

§ Real-time clock (RTC) counts seconds,

minutes hours, date of the month, month, day

of the week, and year with leap-year

compensation valid up to 2100

§ 31-byte, battery-backed, nonvolatile (NV)

RAM for data storage

§ Serial I/O for minimum pin count

§ 2.0V to 5.5V full operation

§ Uses less than 300nA at 2.0V

§ Burst mode for reading/writing successive

addresses in clock/RAM

§ 8-pin DIP or optional 8-pin SOICs for surface

mount

§ Simple 3-wire interface

§ TTL-compatible (V

= 5V)

§ Optional industrial temperature range:

-40°C to +85°C

§ DS1202 compatible

§ Underwriters Laboratory (UL) recognized

ORDERING INFORMATION

DS1302 8-Pin DIP (300-mil)

DS1302N 8-Pin DIP (Industrial)

DS1302S 8-Pin SOIC (200-mil)

DS1302SN 8-Pin SOIC (Industrial)

DS1302Z 8-Pin SOIC (150-mil)

DS1302ZN 8-Pin SOIC (Industrial)

DS1302S-16 16-Pin SOIC (300-mil)

DS1302SN-16 16-Pin SOIC (Industrial)

PIN ASSIGNMENT

PIN DESCRIPTION

X1, X2 - 32.768kHz Crystal Pins

GND - Ground

RST - Reset

I/O - Data Input/Output

SCLK - Serial Clock

CC1

, V

CC2

- Power Supply Pins

DESCRIPTION

The DS1302 Trickle Charge Timekeeping Chip contains an RTC/calendar and 31 bytes of static RAM. It

communicates with a microprocessor via a simple serial interface. The RTC/calendar provides seconds,

minutes, hours, day, date, month, and year information. The end of the month date is automatically

adjusted for months with fewer than 31 days, including corrections for leap year. The clock operates in

either the 24-hour or 12-hour format with an AM/PM indicator.

DS1302

Trickle Charge Timekeeping Chip

www.maxim-ic.com

CC2

GND

CC1

SCLK

I/O

RST

DS1302 8-Pin DIP (300-mil)

CC2

GND

CC1

SCLK

I/O

RST

DS1302 8-Pin SOIC (200-mil)

DS1302 8-Pin SOIC (150-mil)

SCLK

DS1302 16-Pin SOIC (300-mil)

CC1

RST

CC2

GND

DS1302

2 of 15

Interfacing the DS1302 with a microprocessor is simplified by using synchronous serial communication.

Only three wires are required to communicate with the clock/RAM: 1) RST (reset), 2) I/O (data line), and

3) SCLK (serial clock). Data can be transferred to and from the clock/RAM 1 byte at a time or in a burst

of up to 31 bytes. The DS1302 is designed to operate on very low power and retain data and clock

information on less than 1 microwatt.

The DS1302 is the successor to the DS1202. In addition to the basic timekeeping functions of the

DS1202, the DS1302 has the additional features of dual-power pins for primary and back-up power

supplies, programmable trickle charger for V

CC1

, and seven additional bytes of scratchpad memory.

TYPICAL OPERATING CIRCUIT

DS1302

3 of 15

OPERATION

The main elements of the serial timekeeper (i.e., shift register, control logic, oscillator, RTC, and RAM)

are shown in Figure 1.

DS1302 BLOCK DIAGRAM Figure 1

SIGNAL DESCRIPTIONS

CC1

– V

CC1

provides low-power operation in single supply and battery-operated systems as well as low-

power battery backup. In systems using the trickle charger, the rechargeable energy source is connected

to this pin. UL recognized to ensure against reverse charging current when used in conjunction with a

lithium battery.

See “Conditions of Acceptability” at http://www.maxim-ic.com/TechSupport/QA/ntrl.htm.

CC2

– V

CC2

is the primary power supply pin in a dual-supply configuration. V

CC1

is connected to a

backup source to maintain the time and date in the absence of primary power.

The DS1302 will operate from the larger of V

CC1

or V

CC2

. When V

CC2

is greater than V

CC1

+ 0.2V, V

CC2

will power the DS1302. When V

CC2

is less than V

CC1

, V

CC1

will power the DS1302.

SCLK (Serial Clock Input) – SCLK is used to synchronize data movement on the serial interface. This

pin has a 40kΩ internal pull-down resistor.

I/O (Data Input/Output) – The I/O pin is the bi-directional data pin for the 3-wire interface. This pin has

a 40kΩ internal pull-down resistor.

RST (Reset) – The reset signal must be asserted high during a read or a write. This pin has a 40kΩ

internal pull-down resistor.

X1, X2 – Connections for a standard 32.768kHz quartz crystal. The internal oscillator is designed for

operation with a crystal having a specified load capacitance of 6pF. For more information on crystal

selection and crystal layout considerations, please consult Application Note 58, “Crystal Considerations

DS1302

4 of 15

with Dallas Real-Time Clocks.” The DS1302 can also be driven by an external 32.768kHz oscillator. In

this configuration, the X1 pin is connected to the external oscillator signal and the X2 pin is floated.

CLOCK ACCURACY

The accuracy of the clock is dependent upon the accuracy of the crystal and the accuracy of the match

between the capactive load of the oscillator circuit and the capacitive load for which the crystal was

trimmed. Additional error will be added by crystal frequency drift caused by temperature shifts. External

circuit noise coupled into the oscillator circuit may result in the clock running fast. See Application Note

58, “Crystal Considerations with Dallas Real-Time Clocks” for detailed information.

COMMAND BYTE

The command byte is shown in Figure 2. Each data transfer is initiated by a command byte. The MSB

(Bit 7) must be a logic 1. If it is 0, writes to the DS1302 will be disabled. Bit 6 specifies clock/calendar

data if logic 0 or RAM data if logic 1. Bits 1 through 5 specify the designated registers to be input or

output, and the LSB (bit 0) specifies a write operation (input) if logic 0 or read operation (output) if logic

1. The command byte is always input starting with the LSB (bit 0).

ADDRESS/COMMAND BYTE Figure 2

RESET AND CLOCK CONTROL

All data transfers are initiated by driving the RST input high. The RST input serves two functions. First,

RST turns on the control logic, which allows access to the shift register for the address/command

sequence. Second, the

RST signal provides a method of terminating either single byte or multiple byte

data transfer.

A clock cycle is a sequence of a falling edge followed by a rising edge. For data inputs, data must be

valid during the rising edge of the clock and data bits are output on the falling edge of clock. If the

RST

input is low all data transfer terminates and the I/O pin goes to a high impedance state. Data transfer is

illustrated in Figure 3. At power-up,

RST must be a logic 0 until V

> 2.0V. Also SCLK must be at a

logic 0 when

RST is driven to a logic 1 state.

MMENDED LAY

T F

TAL

DS1302

5 of 15

DATA INPUT

Following the eight SCLK cycles that input a write command byte, a data byte is input on the rising edge

of the next eight SCLK cycles. Additional SCLK cycles are ignored should they inadvertently occur.

Data is input starting with bit 0.

DATA OUTPUT

Following the eight SCLK cycles that input a read command byte, a data byte is output on the falling

edge of the next eight SCLK cycles. Note that the first data bit to be transmitted occurs on the first falling

edge after the last bit of the command byte is written. Additional SCLK cycles retransmit the data bytes

should they inadvertently occur so long as RST remains high. This operation permits continuous burst

mode read capability. Also, the I/O pin is tri-stated upon each rising edge of SCLK. Data is output

starting with bit 0.

BURST MODE

Burst mode may be specified for either the clock/calendar or the RAM registers by addressing location 31

decimal (address/command bits 1 through 5 = logic 1). As before, bit 6 specifies clock or RAM and bit 0

specifies read or write. There is no data storage capacity at locations 9 through 31 in the Clock/Calendar

Registers or location 31 in the RAM registers. Reads or writes in burst mode start with bit 0 of address 0.

When writing to the clock registers in the burst mode, the first eight registers must be written in order for

the data to be transferred. However, when writing to RAM in burst mode it is not necessary to write all

31 bytes for the data to transfer. Each byte that is written to will be transferred to RAM regardless of

whether all 31 bytes are written or not.

CLOCK/CALENDAR

The clock/calendar is contained in seven write/read registers as shown in Figure 4. Data contained in the

clock/ calendar registers is in binary coded decimal format (BCD).

CLOCK HALT FLAG

Bit 7 of the seconds register is defined as the clock halt flag. When this bit is set to logic 1, the clock

oscillator is stopped and the DS1302 is placed into a low-power standby mode with a current drain of less

than 100 nanoamps. When this bit is written to logic 0, the clock will start. The initial power on state is

not defined.

AM-PM/12-24 MODE

Bit 7 of the hours register is defined as the 12- or 24-hour mode select bit. When high, the 12-hour mode

is selected. In the 12-hour mode, bit 5 is the AM/PM bit with logic high being PM. In the 24-hour mode,

bit 5 is the second 10-hour bit (20–23 hours).

WRITE PROTECT BIT

Bit 7 of the control register is the write-protect bit. The first seven bits (bits 0–6) are forced to 0 and will

always read a 0 when read. Before any write operation to the clock or RAM, bit 7 must be 0. When high,

the write protect bit prevents a write operation to any other register. The initial power on state is not

defined. Therefore the WP bit should be cleared before attempting to write to the device.

TRICKLE CHARGE REGISTER

This register controls the trickle charge characteristics of the DS1302. The simplified schematic of

Figure 5 shows the basic components of the trickle charger. The trickle charge select (TCS) bits

(bits 4–7) control the selection of the trickle charger. In order to prevent accidental enabling, only a

pattern of 1010 will enable the trickle charger. All other patterns will disable the trickle charger. The

评论收藏

内容反馈

版权申诉

小波思基

粉丝: 74
资源: 1万+

实验9 DS1302实时时钟设计实验程序.rar_DS1302实时时钟设计实验程序

最新资源

实验9 DS1302实时时钟设计实验程序.rar_DS1302实时时钟设计实验程序

基于1602和ds1302的电子时钟设计课程设计（实训报告）

单片机C语言程序设计 1602液晶显示的DS1302实时时钟（有源码)

Arduino 例程详细教学32.DS1302时钟

DS1302实时时钟实验

实时时钟DS1302仿真实验.rar

DS1302时钟实验操作演示.rar

DS1302实时时钟模块.rar

实时时钟模DS1302程序例子

电子-DS1302实时时钟模块.rar

DS1302实时时钟c程序

基于keil+51单片机DS1302的日历时钟设计与实现.rar（源码+仿真）

RTC实时时钟DS1302Z读写实验例程 cyclone2 FPGA实验Verilog源码Quartus9.0工程

DS1302时钟（实时时钟）.zip_ds1302_ds1302 电子时钟_ds1302电子时钟_时钟_电子时钟

基于stc15w的ds1302时钟模块+oled显示.rar

实时时钟DS1302驱动程序.rar_89C52 DS1302_89C52时钟_89c52

DS1302时钟程序STC12C5A60S2.rar

24、实时时钟DS1302.rar

14.DS1302实时时钟实验_keil_

1602液晶显示的DS1302实时时钟.rar

13 1602液晶显示的DS1302实时时钟_单片机_闹钟仿真_lcd1602_walkzvv_ds1302_

STM32F407实时时钟_DS1302实时时钟模块和TM1637四位数码管

14、实时时钟DS1302.rar_DS1302驱动

AVR 实时时钟DS1302 C程序

1602液晶显示DS1302实时时钟程序

DS1302实时时钟带C程序

实验26：DS1302时钟.rar

实验25：DS1302时钟.rar_DS1302驱动_ds1302_fishhyg

冰河的渗透实战笔记-冰河.pdf

大灰狼远控2021最新版，解压密码222

最新资源