ap6212a0_bb16v3_sina33验证通过BT的功能_wifi部分有问题_20170626_1148没有外层目录.7z
调通sina33下的AP6212A0版本的BT 大文实验室/大文哥 壹捌陆捌零陆捌捌陆捌贰 wb4916 AT qq.com 完成时间:2017/6/26 11:01 版本:V1.0 本文参照: 《A33 wifi移植说明书.pdf》 还有就是全志R16的parrotv1.1的官方SDK(Android4.4.2) 1、打开AP6212的BT,关闭rtl8723bs的BT: [ 3.141273] Bluetooth: HCI UART driver ver 2.2 [ 3.146210] Bluetooth: HCI H4 protocol initialized [ 3.151563] Bluetooth: HCI BCSP protocol initialized [ 3.157154] usbcore: registered new interface driver btusb [ 3.163282] Bluetooth: Generic Bluetooth SDIO driver ver 0.1 [ 3.169599] Bluetooth: BlueSleep Mode Driver Ver 1.1 [ 3.175402] Bluetooth: get rtl8723bs rtl8723bs_bt_host_wake gpio failed [ 3.953017] Bluetooth: RFCOMM TTY layer initialized [ 3.958456] Bluetooth: RFCOMM socket layer initialized [ 3.964183] Bluetooth: RFCOMM ver 1.11 [ 3.968340] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 3.968638] [mmc]: sdc2 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 3.968734] [mmc]: mclk 0xf1c20090 0xc100000b [ 3.989421] Bluetooth: BNEP filters: protocol multicast [ 3.995242] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 4.001921] L2TP core driver, V2.0 [ 4.005706] PPPoL2TP kernel driver, V2.0 [ 4.010070] L2TP IP encapsulation support (L2TPv3) [ 4.015468] L2TP netlink interface [ 4.019264] L2TP ethernet pseudowire support (L2TPv3) [ 4.023860] [mmc]: sdc2 set ios: clk 25000000Hz bm PP pm ON vdd 3.3V width 1 timing MMC-HS(SDR20) dt B [ 4.023929] [mmc]: mclk 0xf1c20090 0xc100000b [ 4.040272] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 4.048780] ThumbEE CPU extension supported. [ 4.053550] Registering SWP/SWPB emulation handler [ 4.059269] [rfkill]: rfkill set power 1 [ 4.063652] gpio ap6xxx_bt_regon set val 0, act val 0 rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r$ ll rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ ./build.sh config Welcome to mkscript setup progress All available chips: 0. sun8iw5p1 Choice: 0 All available platforms: 0. android 1. dragonboard 2. linux Choice: 0 All available kernel: 0. linux-3.4 Choice: 0 All available boards: 0. evb 1. maple 2. redwood 3. y2 4. y3 Choice: 4 rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee$ cd linux-3.4/ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4$ make ARCH=arm menuconfig [*] Networking support ---> <*> Bluetooth subsystem support ---> Bluetooth device drivers ---> < > Broadcom Bluetooth Low Power Manager Support <*> Realtek Bluesleep driver support 修改为: <*> Broadcom Bluetooth Low Power Manager Support < > An inverter between bt hostwake pin and cpu (NEW) < > Realtek Bluesleep driver support 2、(这个不修改:) R:\wyb\ap6212a0_a33_sc3817r\android\device\softwinner\astar-y3\overlay\frameworks\base\core\res\res\values\config.xml <!-- List of regexpressions describing the interface (if any) that represent tetherable Wifi interfaces. If the device doesn't want to support tethering over Wifi this should be empty. An example would be "softap.*" --> <string-array translatable="false" name="config_tether_wifi_regexs"> <item>"wlan0"</item> </string-array> <!-- List of regexpressions describing the interface (if any) that represent tetherable bluetooth interfaces. If the device doesn't want to support tethering over bluetooth this should be empty. --> <!-- default: disable Bluetooth PAN feature --> <string-array translatable="false" name="config_tether_bluetooth_regexs"> <item>"bt-pan"</item> </string-array> 3、 R:\wyb\ap6212a0_a33_sc3817r\android\device\softwinner\astar-y3\astar_y3.mk # ap6181/6210/6330 sdio wifi fw and nvram #$(call inherit-product-if-exists, hardware/broadcom/wlan/firmware/ap6181/device-bcm.mk) #$(call inherit-product-if-exists, hardware/broadcom/wlan/firmware/ap6210/device-bcm.mk) $(call inherit-product-if-exists, hardware/broadcom/wlan/firmware/ap6212/device-bcm.mk) #$(call inherit-product-if-exists, hardware/broadcom/wlan/firmware/ap6330/device-bcm.mk) #rtl8723bs bt fw and config #$(call inherit-product, hardware/realtek/bluetooth/rtl8723bs/firmware/rtlbtfw_cfg.mk) # camera config for camera detector #PRODUCT_COPY_FILES += \ # device/softwinner/astar-y3/hawkview/sensor_list_cfg.ini:system/etc/hawkview/sensor_list_cfg.ini #add gms features #PRODUCT_COPY_FILES += \ # frameworks/native/data/etc/android.hardware.faketouch.xml:system/etc/permissions/android.hardware.faketouch.xml \ # frameworks/native/data/etc/android.hardware.touchscreen.multitouch.jazzhand.xml:system/etc/permissions/android.hardware.touchscreen.multitouch.jazzhand.xml \ # frameworks/native/data/etc/android.hardware.usb.host.xml:system/etc/permissions/android.hardware.usb.host.xml # 3G Data Card Packages #PRODUCT_PACKAGES += \ # u3gmonitor \ # chat \ # rild \ # pppd # 3G Data Card Configuration Flie #PRODUCT_COPY_FILES += \ # device/softwinner/polaris-common/rild/ip-down:system/etc/ppp/ip-down \ # device/softwinner/polaris-common/rild/ip-up:system/etc/ppp/ip-up \ # device/softwinner/polaris-common/rild/3g_dongle.cfg:system/etc/3g_dongle.cfg \ # device/softwinner/polaris-common/rild/usb_modeswitch:system/bin/usb_modeswitch \ # device/softwinner/polaris-common/rild/call-pppd:system/xbin/call-pppd \ # device/softwinner/polaris-common/rild/usb_modeswitch.sh:system/xbin/usb_modeswitch.sh \ # device/softwinner/polaris-common/rild/apns-conf_sdk.xml:system/etc/apns-conf.xml \ # device/softwinner/polaris-common/rild/libsoftwinner-ril.so:system/lib/libsoftwinner-ril.so #PRODUCT_COPY_FILES += \ # device/softwinner/polaris-common/rild/init.3gdongle.rc:root/init.sunxi.3gdongle.rc # 3G Data Card usb modeswitch File #PRODUCT_COPY_FILES += \ # $(call find-copy-subdir-files,*,device/softwinner/polaris-common/rild/usb_modeswitch.d,system/etc/usb_modeswitch.d) PRODUCT_PROPERTY_OVERRIDES += \ ro.sw.embeded.telephony = false PRODUCT_PROPERTY_OVERRIDES += \ persist.sys.timezone=Asia/Shanghai \ persist.sys.language=zh \ persist.sys.country=CN PRODUCT_PACKAGES += Bluetooth #PRODUCT_PROPERTY_OVERRIDES += \ # ro.product.8723b_bt.used=true #GPS Feature #PRODUCT_PACKAGES += gps.polaris #BOARD_USES_GPS_TYPE := simulator #PRODUCT_COPY_FILES += frameworks/native/data/etc/android.hardware.location.xml:system/etc/permissions/android.hardware.location.xml # evb logger PRODUCT_COPY_FILES += \ device/softwinner/astar-y3/tools/logger.sh:system/bin/logger.sh PRODUCT_PROPERTY_OVERRIDES += \ persist.sys.usb.config=mass_storage,adb \ ro.adb.secure=0 ro.udisk.lable=Polaris \ ro.font.scale=1.0 \ ro.hwa.force=false \ rw.logger=0 \ ro.sys.bootfast=true \ debug.hwc.showfps=0 \ debug.hwui.render_dirty_regions=false #ro.sys.storage_type = emulated \ #for gms #PRODUCT_PROPERTY_OVERRIDES += \ # ro.sys.mutedrm=true \ # ro.adb.secure=1 PRODUCT_PROPERTY_OVERRIDES += \ ro.sf.lcd_density=213 \ ro.product.firmware=v2.0 $(call inherit-product-if-exists, device/softwinner/astar-y3/modules/modules.mk) DEVICE_PACKAGE_OVERLAYS := device/softwinner/astar-y3/overlay PRODUCT_CHARACTERISTICS := tablet # Overrides PRODUCT_AAPT_CONFIG := xlarge hdpi xhdpi large PRODUCT_AAPT_PREF_CONFIG := xhdpi PRODUCT_BRAND := Allwinner PRODUCT_NAME := astar_y3 PRODUCT_DEVICE := astar-y3 PRODUCT_MODEL := QUAD-CORE A33 y3 PRODUCT_MANUFACTURER := softwinner #include device/softwinner/polaris-common/prebuild/google/products/gms_base.mk 4、 R:\wyb\ap6212a0_a33_sc3817r\android\device\softwinner\astar-y3\BoardConfig.mk # wifi and bt configuration # 1. Wifi Configuration # 1.1 realtek wifi support # 1.1 realtek wifi configuration #BOARD_WIFI_VENDOR := realtek ifeq ($(BOARD_WIFI_VENDOR), realtek) WPA_SUPPLICANT_VERSION := VER_0_8_X BOARD_WPA_SUPPLICANT_DRIVER := NL80211 BOARD_WPA_SUPPLICANT_PRIVATE_LIB := lib_driver_cmd_rtl BOARD_HOSTAPD_DRIVER := NL80211 BOARD_HOSTAPD_PRIVATE_LIB := lib_driver_cmd_rtl SW_BOARD_USR_WIFI := rtl8188eu BOARD_WLAN_DEVICE := rtl8188eu #SW_BOARD_USR_WIFI := rtl8723au #BOARD_WLAN_DEVICE := rtl8723au #SW_BOARD_USR_WIFI := rtl8723bs #BOARD_WLAN_DEVICE := rtl8723bs endif # 1.2 broadcom wifi support BOARD_WIFI_VENDOR := broadcom ifeq ($(BOARD_WIFI_VENDOR), broadcom) BOARD_WPA_SUPPLICANT_DRIVER := NL80211 WPA_SUPPLICANT_VERSION := VER_0_8_X BOARD_WPA_SUPPLICANT_PRIVATE_LIB := lib_driver_cmd_bcmdhd BOARD_HOSTAPD_DRIVER := NL80211 BOARD_HOSTAPD_PRIVATE_LIB := lib_driver_cmd_bcmdhd BOARD_WLAN_DEVICE := bcmdhd WIFI_DRIVER_FW_PATH_PARAM := "/sys/module/bcmdhd/parameters/firmware_path" #SW_BOARD_USR_WIFI := AP6181 #SW_BOARD_USR_WIFI := AP6210 #WIFI_DRIVER_FW_PATH_STA := "/system/vendor/modules/fw_bcm40181a2.bin" #WIFI_DRIVER_FW_PATH_P2P := "/system/vendor/modules/fw_bcm40181a2_p2p.bin" #WIFI_DRIVER_FW_PATH_AP := "/system/vendor/modules/fw_bcm40181a2_apsta.bin" # 2017/6/21 15:11 wenyuanbo configure ap6212 use ap6210 SW_BOARD_USR_WIFI := AP6212 WIFI_DRIVER_FW_PATH_STA := "/system/vendor/modules/fw_bcm43438a0.bin" WIFI_DRIVER_FW_PATH_P2P := "/system/vendor/modules/fw_bcm43438a0_p2p.bin" WIFI_DRIVER_FW_PATH_AP := "/system/vendor/modules/fw_bcm43438a0_apsta.bin" #SW_BOARD_USR_WIFI := AP6330 #WIFI_DRIVER_FW_PATH_STA := "/system/vendor/modules/fw_bcm40183b2_ag.bin" #WIFI_DRIVER_FW_PATH_P2P := "/system/vendor/modules/fw_bcm40183b2_ag_p2p.bin" #WIFI_DRIVER_FW_PATH_AP := "/system/vendor/modules/fw_bcm40183b2_ag_apsta.bin" endif #1.3 eag wifi config #BOARD_WIFI_VENDOR := eagle ifeq ($(BOARD_WIFI_VENDOR), eagle) WPA_SUPPLICANT_VERSION := VER_0_8_X BOARD_WPA_SUPPLICANT_DRIVER := NL80211 BOARD_WPA_SUPPLICANT_PRIVATE_LIB := lib_driver_cmd_eagle BOARD_HOSTAPD_DRIVER := NL80211 BOARD_HOSTAPD_PRIVATE_LIB := lib_driver_cmd_eagle SW_BOARD_USR_WIFI := esp8089 BOARD_WLAN_DEVICE := esp8089 endif # 2. Bluetooth Configuration # make sure BOARD_HAVE_BLUETOOTH is true for every bt vendor BOARD_HAVE_BLUETOOTH := true BOARD_HAVE_BLUETOOTH_BCM := true #SW_BOARD_HAVE_BLUETOOTH_NAME := ap6210 SW_BOARD_HAVE_BLUETOOTH_NAME := ap6212 #SW_BOARD_HAVE_BLUETOOTH_NAME := ap6330 #BOARD_HAVE_BLUETOOTH_RTK := true #BLUETOOTH_HCI_USE_RTK_H5 := true #SW_BOARD_HAVE_BLUETOOTH_NAME := rtl8723bs 5、 R:\wyb\ap6212a0_a33_sc3817r\android\device\softwinner\astar-y3\init.sun8i.rc on early-fs mount_all /fstab.sun8i setprop ro.crypto.fuse_sdcard true insmod /system/vendor/modules/disp.ko insmod /system/vendor/modules/lcd.ko insmod /system/vendor/modules/mali.ko insmod /system/vendor/modules/leds-sunxi.ko insmod /system/vendor/modules/bcmdhd.ko insmod /system/vendor/modules/bcm_btlpm.ko #2G or 3G init.rc # import init.sunxi.3gdongle.rc ## 1. realtek & eagle wifi service ## 1.1 realtek & eagle wifi sta service #service wpa_supplicant /system/bin/wpa_supplicant \ # -iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \ # -O/data/misc/wifi/sockets \ # -e/data/misc/wifi/entropy.bin -g@android:wpa_wlan0 # # we will start as root and wpa_supplicant will switch to user wifi # # after setting up the capabilities required for WEXT # # user wifi # # group wifi inet keystore # class main # socket wpa_wlan0 dgram 660 wifi wifi # disabled # oneshot # ## 1.2 realtek & eagle wifi sta p2p concurrent service #service p2p_supplicant /system/bin/wpa_supplicant \ # -ip2p0 -Dnl80211 -c/data/misc/wifi/p2p_supplicant.conf \ # -e/data/misc/wifi/entropy.bin -N \ # -iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \ # -O/data/misc/wifi/sockets \ # -g@android:wpa_wlan0 # class main # socket wpa_wlan0 dgram 660 wifi wifi # disabled # oneshot # 2. broadcom wifi service # 2.1 broadcom wifi station and softap service wpa_supplicant /system/bin/wpa_supplicant \ -iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \ -I/system/etc/wifi/wpa_supplicant_overlay.conf \ -O/data/misc/wifi/sockets \ -e/data/misc/wifi/entropy.bin -g@android:wpa_wlan0 # we will start as root and wpa_supplicant will switch to user wifi # after setting up the capabilities required for WEXT # user wifi # group wifi inet keystore class main socket wpa_wlan0 dgram 660 wifi wifi disabled oneshot # 2.2 broadcom wifi sta p2p concurrent service service p2p_supplicant /system/bin/wpa_supplicant \ -iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \ -I/system/etc/wifi/wpa_supplicant_overlay.conf \ -O/data/misc/wifi/sockets -N \ -ip2p0 -Dnl80211 -c/data/misc/wifi/p2p_supplicant.conf \ -I/system/etc/wifi/p2p_supplicant_overlay.conf \ -puse_p2p_group_interface=1 -e/data/misc/wifi/entropy.bin \ -g@android:wpa_wlan0 # we will start as root and wpa_supplicant will switch to user wifi # after setting up the capabilities required for WEXT # user wifi # group wifi inet keystore class main socket wpa_wlan0 dgram 660 wifi wifi disabled oneshot 6、(不需要修改) R:\wyb\ap6212a0_a33_sc3817r\android\device\softwinner\astar-y3\ueventd.sun8i.rc 7、 R:\wyb\ap6212a0_a33_sc3817r\android\frameworks\base\packages\SettingsProvider\res\values\defaults.xml <integer name="def_screen_off_timeout">1800000</integer> <bool name="def_lockscreen_disabled">true</bool> 8、 R:\wyb\ap6212a0_a33_sc3817r\android\frameworks\base\services\java\com\android\server\BatteryService.java // private static final boolean DEBUG = false; private static final boolean DEBUG = true; private void sendIntentLocked() { // Pack up the values and broadcast them to everyone final Intent intent = new Intent(Intent.ACTION_BATTERY_CHANGED); intent.addFlags(Intent.FLAG_RECEIVER_REGISTERED_ONLY | Intent.FLAG_RECEIVER_REPLACE_PENDING); int icon = getIconLocked(mBatteryProps.batteryLevel); intent.putExtra(BatteryManager.EXTRA_STATUS, mBatteryProps.batteryStatus); intent.putExtra(BatteryManager.EXTRA_HEALTH, mBatteryProps.batteryHealth); intent.putExtra(BatteryManager.EXTRA_PRESENT, mBatteryProps.batteryPresent); //intent.putExtra(BatteryManager.EXTRA_LEVEL, mBatteryProps.batteryLevel); intent.putExtra(BatteryManager.EXTRA_LEVEL, 100); intent.putExtra(BatteryManager.EXTRA_SCALE, BATTERY_SCALE); intent.putExtra(BatteryManager.EXTRA_ICON_SMALL, icon); intent.putExtra(BatteryManager.EXTRA_PLUGGED, mPlugType); //intent.putExtra(BatteryManager.EXTRA_VOLTAGE, mBatteryProps.batteryVoltage); intent.putExtra(BatteryManager.EXTRA_VOLTAGE, 4200); intent.putExtra(BatteryManager.EXTRA_TEMPERATURE, mBatteryProps.batteryTemperature); intent.putExtra(BatteryManager.EXTRA_TECHNOLOGY, mBatteryProps.batteryTechnology); intent.putExtra(BatteryManager.EXTRA_INVALID_CHARGER, mInvalidCharger); if (DEBUG) { Slog.d(TAG, "2016/12/05 10:41 wenyuanbo **** Sending ACTION_BATTERY_CHANGED. level:" + mBatteryProps.batteryLevel + ", scale:" + BATTERY_SCALE + ", status:" + mBatteryProps.batteryStatus + ", health:" + mBatteryProps.batteryHealth + ", present:" + mBatteryProps.batteryPresent + ", voltage: " + mBatteryProps.batteryVoltage + ", temperature: " + mBatteryProps.batteryTemperature + ", technology: " + mBatteryProps.batteryTechnology + ", AC powered:" + mBatteryProps.chargerAcOnline + ", USB powered:" + mBatteryProps.chargerUsbOnline + ", Wireless powered:" + mBatteryProps.chargerWirelessOnline + ", icon:" + icon + ", invalid charger:" + mInvalidCharger); } mHandler.post(new Runnable() { @Override public void run() { ActivityManagerNative.broadcastStickyIntent(intent, null, UserHandle.USER_ALL); } }); } 9、(直接拷贝同目录下的ap6210:) R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\conf\softwinner\ap6212\Android.mk LOCAL_PATH := $(call my-dir) include $(CLEAR_VARS) LOCAL_MODULE := bt_vendor.conf LOCAL_MODULE_CLASS := ETC LOCAL_MODULE_PATH := $(TARGET_OUT)/etc/bluetooth LOCAL_MODULE_TAGS := eng LOCAL_SRC_FILES := $(LOCAL_MODULE) include $(BUILD_PREBUILT) R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\conf\softwinner\ap6212\bt_vendor.conf # UART device port where Bluetooth controller is attached UartPort = /dev/ttyS1 # Firmware patch file location FwPatchFilePath = /system/vendor/modules/ # Firmware Name FwPatchFileName = bcm43438a0.hcd 10、新增:vnd_astar-y3-ap6212.txt,直接拷贝:vnd_astar-y2-ap6210.txt R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\include\vnd_astar-y3-ap6212.txt R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\include\vnd_astar-y2-ap6210.txt BLUETOOTH_UART_DEVICE_PORT = "/dev/ttyS1" FW_PATCHFILE_LOCATION = "/system/vendor/modules/" LPM_IDLE_TIMEOUT_MULTIPLE = 5 UART_TARGET_BAUD_RATE = 1500000 BT_WAKE_VIA_PROC = TRUE #LPM_SLEEP_MODE = FALSE BTVND_DBG = TRUE BTHW_DBG = TRUE VNDUSERIAL_DBG = TRUE UPIO_DBG = TRUE 11、 R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\src\userial_vendor.c //#ifdef USE_AP6210_BT_MODULE #if defined(USE_AP6210_BT_MODULE) || defined(USE_AP6212_BT_MODULE) /* PATCH for AP6210. Will detect CTS(module side) to select transport mode*/ ALOGE("userial vendor open: USE AP6210 BT MODULE."); usleep(100000); close(vnd_userial.fd); if ((vnd_userial.fd = open(vnd_userial.port_name, O_RDWR)) == -1) { ALOGE("userial vendor open: unable to open %s", vnd_userial.port_name); return -1; } #endif //USE_AP6210_BT_MODULE 12、 R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\Android.mk ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6210) LOCAL_CFLAGS += -DUSE_AP6210_BT_MODULE endif ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6212) LOCAL_CFLAGS += -DUSE_AP6212_BT_MODULE endif ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6330) include $(LOCAL_PATH)/conf/softwinner/ap6330/Android.mk endif ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6210) include $(LOCAL_PATH)/conf/softwinner/ap6210/Android.mk endif ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6212) include $(LOCAL_PATH)/conf/softwinner/ap6212/Android.mk endif 13、 R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\libbt\vnd_buildcfg.mk ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6210) SRC := $(call my-dir)/include/$(addprefix vnd_, $(addsuffix -ap6210.txt,$(basename $(TARGET_DEVICE)))) endif ifeq ($(SW_BOARD_HAVE_BLUETOOTH_NAME), ap6212) SRC := $(call my-dir)/include/$(addprefix vnd_, $(addsuffix -ap6212.txt,$(basename $(TARGET_DEVICE)))) endif 14、(这些AP6212的WIFI的bin文件和BT的hcd文件来自全志R16的SDK,当然也可以找正基原厂/代理商索取:) R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\wlan\firmware\ap6212\bcm43438a0.hcd (根据ap6210修改:) R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\wlan\firmware\ap6212\device-bcm.mk # # Copyright (C) 2008 The Android Open Source Project # # Licensed under the Apache License, Version 2.0 (the "License"); # you may not use this file except in compliance with the License. # You may obtain a copy of the License at # # http://www.apache.org/licenses/LICENSE-2.0 # # Unless required by applicable law or agreed to in writing, software # distributed under the License is distributed on an "AS IS" BASIS, # WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. # See the License for the specific language governing permissions and # limitations under the License. # ######################## -include hardware/broadcom/wlan/bcmdhd/config/config-bcm.mk PRODUCT_COPY_FILES += \ hardware/broadcom/wlan/firmware/ap6212/fw_bcm43438a0.bin:system/vendor/modules/fw_bcm43438a0.bin \ hardware/broadcom/wlan/firmware/ap6212/fw_bcm43438a0_apsta.bin:system/vendor/modules/fw_bcm43438a0_apsta.bin \ hardware/broadcom/wlan/firmware/ap6212/fw_bcm43438a0_p2p.bin:system/vendor/modules/fw_bcm43438a0_p2p.bin \ hardware/broadcom/wlan/firmware/ap6212/nvram_ap6212.txt:system/vendor/modules/nvram_ap6212.txt \ hardware/broadcom/wlan/firmware/ap6212/bcm43438a0.hcd:system/vendor/modules/bcm43438a0.hcd #hardware/broadcom/wlan/firmware/ap6212/config.txt:system/vendor/modules/config.txt ######################## R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\wlan\firmware\ap6212\fw_bcm43438a0.bin R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\wlan\firmware\ap6212\fw_bcm43438a0_apsta.bin R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\wlan\firmware\ap6212\fw_bcm43438a0_p2p.bin R:\wyb\ap6212a0_a33_sc3817r\android\hardware\broadcom\wlan\firmware\ap6212\nvram_ap6212.txt 15、(可选修改:) R:\wyb\ap6212a0_a33_sc3817r\android\packages\apps\Camera2\src\com\android\camera\CameraActivity.java private BroadcastReceiver mBatteryInfoReceiver = new BroadcastReceiver() { @Override public void onReceive(Context context, Intent intent) { String action = intent.getAction(); if (Intent.ACTION_BATTERY_CHANGED.equals(action)) { int Level = intent.getIntExtra("level", 0); int Scale = intent.getIntExtra("scale", 100); Log.w(TAG, "2016/11/29 19:54 &&&& wenyuanbo battery Level" + Level); /* *Logic: *1.the battery level is lower then 5%. *2.if in camera, make sure that not in the snapshot progress. *3.if in videocamera, make sure that not in the videorecording progress. *4.everytime starting the camera activity, the battery level is broadcasted, * if meeting the conditions above, give a dialog, press it and finish the activity. *5.if the conditions are not satisfied when started, play for a moment, in the camera acitvity * or video camera activity, the conditiosn are satisfied, also give a dialog for finishing the activity. * *by fuqiang. */ if(Level < 5) { Runnable runnable_close_camera = new Runnable() { @Override public void run() { //close the camera. // CameraActivity.this.finish(); } }; Log.w(TAG, "2016/11/29 18:20 **** wenyuanbo battery Level" + Level); showLocationDialog(); } /* *Logic: *1.the battery level is lhigher then 5% and lower than 15%. *2.if in camera, make sure that not in the snapshot progress. *3.if in videocamera, make sure that not in the videorecording progress. *4.whether in camera or in videocamera, make sure that the flash mode is supported. *5.everytime starting the camera activity, the battery level is broadcasted, * if meeting the conditions above, forbidden the flash(gray icon), give a dialog to notise user. *6.if the conditions are not satisfied when started, play for a moment, in the camera acitvity * or video camera activity, the conditiosn are satisfied, forbidden the flash and give a notice dialog. *7.the dialog is only given once for each camera activity starting. * *by fuqiang. */ else if(Level < 16) { //close the flash mode. /* if (mIsLowBatteryDialogShown == false) { mRotateDialog.showAlertDialog( getString(R.string.warning), getString(R.string.low_battery_15), null, null, getString(R.string.close), null); mIsLowBatteryDialogShown = true; } */ } } } }; 16、(可选:) R:\wyb\ap6212a0_a33_sc3817r\lichee\tools\pack\chips\sun8iw5p1\configs\default\env.cfg bootdelay=3 loglevel=8 17、 R:\wyb\ap6212a0_a33_sc3817r\lichee\tools\pack\chips\sun8iw5p1\configs\y3\sys_config.fex [power_sply] dcdc1_vol = 3000 dcdc2_vol = 1100 dcdc3_vol = 1200 dcdc4_vol = 0 dcdc5_vol = 1500 aldo1_vol = 3300 aldo2_vol = 2500 aldo3_vol = 3000 dldo1_vol = 3300 dldo2_vol = 3300 dldo3_vol = 2800 ;gpio0_vol = 2800 ldoio0_vol = 2800 ;---------------------------------------------------------------------------------- ;uart configuration ;uart_used = uart x enable ;uart_type = 2:2 wire,4:4 wire,8:8 wire, full function ;---------------------------------------------------------------------------------- [uart0] uart_used = 1 uart_port = 0 uart_type = 2 uart_tx = port:PF02<3><1><default><default> uart_rx = port:PF04<3><1><default><default> [uart1] uart_used = 1 uart_port = 1 uart_type = 4 uart_tx = port:PG06<2><1><default><default> uart_rx = port:PG07<2><1><default><default> uart_rts = port:PG08<2><1><default><default> uart_cts = port:PG09<2><1><default><default> [uart2] uart_used = 1 uart_type = 4 uart_tx = port:PB00<2><1><default><default> uart_rx = port:PB01<2><1><default><default> uart_rts = port:PB02<2><1><default><default> uart_cts = port:PB03<2><1><default><default> [uart3] uart_used = 0 uart_type = 4 uart_tx = port:PH06<3><1><default><default> uart_rx = port:PH07<3><1><default><default> uart_rts = port:PH08<3><1><default><default> uart_cts = port:PH09<3><1><default><default> [uart4] uart_used = 0 uart_port = 4 uart_type = 2 uart_tx = port:PA04<2><1><default><default> uart_rx = port:PA05<2><1><default><default> uart_rts = port:PA06<2><1><default><default> uart_cts = port:PA07<2><1><default><default> ;---------------------------------------------------------------------------------- ;capacitor tp configuration ;ctp_twi_id : twi controller ID ;ctp_twi_addr : I2C slave address, 7bit ;ctp_screen_max_x/_y : resolution of touch panel ;ctp_revert_x/_y_flag : whether need to revert x/y ;ctp_exchange_x_y_flag: whether need to exchange the value of x and y ;ctp_int_port : port for tp's interrupt signal ;ctp_wakeup : port for wakeup tp ;---------------------------------------------------------------------------------- [ctp_para] ctp_used = 1 ctp_name = "gt82x" ctp_twi_id = 0 ctp_twi_addr = 0x5d ctp_screen_max_x = 1280 ctp_screen_max_y = 800 ctp_revert_x_flag = 1 ctp_revert_y_flag = 1 ctp_exchange_x_y_flag = 1 ctp_int_port = port:PL04<4><default><default><default> ctp_wakeup = port:PL03<1><default><default><1> ctp_power_ldo = ctp_power_ldo_vol = ctp_power_io = ;-------------------------------------------------------------------------------- ; CTP automatic detection configuration ;ctp_detect_used --- Whether startup automatic inspection function. 1:used,0:unused ;Module name postposition 1 said detection, 0 means no detection. ;-------------------------------------------------------------------------------- [ctp_list_para] ctp_det_used = 1 ft5x_ts = 1 gt82x = 1 gslX680 = 1 gslX680new = 0 gt9xx_ts = 1 gt9xxf_ts = 0 tu_ts = 0 gt818_ts = 1 zet622x = 1 aw5306_ts = 1 icn83xx_ts = 0 [lcd0_para] lcd_used = 1 lcd_driver_name = "default_lcd" lcd_if = 3 lcd_x = 1280 lcd_y = 800 lcd_width = 150 lcd_height = 94 lcd_dclk_freq = 71 lcd_pwm_used = 1 lcd_pwm_ch = 0 lcd_pwm_freq = 50000 lcd_pwm_pol = 1 lcd_hbp = 20 lcd_ht = 1418 lcd_hspw = 10 lcd_vbp = 10 lcd_vt = 830 lcd_vspw = 5 lcd_lvds_if = 0 lcd_lvds_colordepth = 1 lcd_lvds_mode = 0 lcd_frm = 1 lcd_gamma_en = 0 lcd_bright_curve_en = 0 lcd_cmap_en = 0 deu_mode = 0 lcdgamma4iep = 22 smart_color = 90 lcd_bl_en = port:PD13<1><0><default><1> ;ap6xxx_wl_regon = port:PL06<1><default><default><0> ;lcd_bl_en = port:PL06<1><0><default><1> lcd_power = "axp22_dc1sw" lcdd0 = port:PD18<3><0><default><default> lcdd1 = port:PD19<3><0><default><default> lcdd2 = port:PD20<3><0><default><default> lcdd3 = port:PD21<3><0><default><default> lcdd4 = port:PD22<3><0><default><default> lcdd5 = port:PD23<3><0><default><default> lcdd6 = port:PD24<3><0><default><default> lcdd7 = port:PD25<3><0><default><default> lcdd8 = port:PD26<3><0><default><default> lcdd9 = port:PD27<3><0><default><default> ;---------------------------------------------------------------------------------- ;pwm config ;---------------------------------------------------------------------------------- [pwm0_para] pwm_used = 0 pwm_positive = port:PH00<2><0><default><default> [pwm1_para] pwm_used = 1 pwm_positive = port:PH01<2><0><default><default> ;-------------------------------------------------------------------------------- ;wifi configuration ;wifi_sdc_id: 0- SDC0, 1- SDC1, 2- SDC2, 3- SDC3 ;wifi_usbc_id: 0- USB0, 1- USB1, 2- USB2 ;wifi_usbc_type: 1- EHCI(speed 2.0), 2- OHCI(speed 1.0) ;wifi_mod_sel: 0- none, 1- ap6181, 2- ap6210(wifi+bt), ; 3 - rtl8188eu, 4- rtl8723au(wifi+bt), ; 5 - rtl8723bs, 6- esp8089 ;-------------------------------------------------------------------------------- [wifi_para] wifi_used = 1 wifi_sdc_id = 1 wifi_usbc_id = 1 wifi_usbc_type = 1 wifi_mod_sel = 2 wifi_power = "axp22_dldo1" wifi_power_ext1 = "axp22_dldo2" wifi_power_ext2 = "axp22_aldo1" wifi_power_switch = ;wifi_power_switch = port:power0<1><0><default><0> ; 1 - ap6181 sdio wifi gpio config ;ap6xxx_wl_regon = port:PL06<1><default><default><0> ;ap6xxx_wl_host_wake = port:PL07<4><default><default><0> ;ap6xxx_lpo_use_apclk = 1 ; 2 - ap6210 sdio wifi gpio config ap6xxx_wl_regon = port:PL06<1><default><default><0> ;ap6xxx_wl_regon = port:PD13<1><default><default><0> ap6xxx_wl_host_wake = port:PL07<4><default><default><0> ap6xxx_bt_regon = port:PL08<1><default><default><0> ap6xxx_bt_wake = port:PL10<1><default><default><0> ap6xxx_bt_host_wake = port:PL09<4><default><default><0> ap6xxx_lpo_use_apclk = 1 ; 3 - rtl8188eu usb wifi gpio conifg ; 4 - rtl8723au usb wifi + bt ; 5 - rtl8723bs sdio wifi + bt ;rtl8723bs_chip_en = port:PL11<1><default><default><0> ;rtl8723bs_wl_regon = port:PL06<1><default><default><0> ;rtl8723bs_wl_host_wake = port:PL07<4><default><default><0> ;rtl8723bs_bt_regon = port:PL08<1><default><default><0> ;rtl8723bs_bt_wake = port:PL10<1><default><default><0> ;rtl8723bs_bt_host_wake = port:PL09<4><default><default><0> ;rtl8723bs_lpo_use_apclk = 0 ; 6 - eagle sdio wifi ;esp_wl_chip_en = port:PL03<1><default><default><0> ;esp_wl_rst = port:PL02<1><default><default><0> ;-------------------------------------------------------------------------------- ;blue tooth ;bt_used ---- blue tooth used (0- no used, 1- used) ;bt_uard_id ---- uart index ;-------------------------------------------------------------------------------- [bt_para] bt_used = 1 bt_uart_id = 1 power_start = 3 pmu_temp_enable = 0 18、 刷机之后,BT可以用。 传输4.5MB的JPG图片大概需要2分钟。 WIFI: 在设置→WLAN(打开之后): shell@astar-y3:/ $ shell@astar-y3:/ $ [ 469.609956] init: computing context for service '/system/bin/wpa_supplicant' [ 469.618386] init: starting 'p2p_supplicant' [ 469.625739] init: Created socket '/dev/socket/wpa_wlan0' with mode '660', user '1010', group '1010' [ 469.673379] init: waitpid returned pid 2065, status = 0000ff00 [ 469.679923] init: process 'p2p_supplicant', pid 2065 exited [ 476.197334] sndpcm_unmute,line:1099 [ 451.464755] CPU1: Booted secondary processor [ 478.459403] CPU1: shutdown [ 478.462947] [hotplug]: cpu(0) try to kill cpu(1) [ 478.468478] [hotplug]: cpu1 is killed! . shell@astar-y3:/ $ 分析启动的log: [ 17.526849] gpio ap6xxx_wl_regon set val 1, act val 1 [ 17.632508] [ap6xxx]: sdio wifi power state: on [ 17.637576] [mmc]: sdc1 set ios: clk 0Hz bm PP pm UP vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 17.637751] =========== WLAN placed in POWER ON ======== [ 17.654651] [mmc]: sdc1 card_power_on start... [ 17.659576] [mmc]: sdc1 power_supply is null [ 17.664322] [mmc]: sdc1 card_power_on ok [ 17.680039] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 17.690275] [mmc]: mclk 0xf1c2008c 0x8002000e [ 17.772361] [mmc]: *** sunxi_mci_dump_errinfo(L773): smc 1 err, cmd 52, RTO !! [ 17.781309] [mmc]: *** sunxi_mci_dump_errinfo(L773): smc 1 err, cmd 52, RTO !! [ 17.789448] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 17.799714] [mmc]: mclk 0xf1c2008c 0x8002000e [ 17.862032] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 17.872262] [mmc]: mclk 0xf1c2008c 0x8002000e [ 17.933953] [mmc]: *** sunxi_mci_dump_errinfo(L773): smc 1 err, cmd 8, RTO !! [ 17.941997] *******************Try sdio******************* [ 17.948400] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 17.958630] [mmc]: mclk 0xf1c2008c 0x8002000e [ 18.027775] mmc1: queuing unknown CIS tuple 0x80 (2 bytes) [ 18.035416] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 18.043087] mmc1: queuing unknown CIS tuple 0x80 (3 bytes) [ 18.051920] mmc1: queuing unknown CIS tuple 0x80 (7 bytes) [ 18.145287] [mmc]: sdc1 set ios: clk 400000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B [ 18.155436] [mmc]: mclk 0xf1c2008c 0x8002000e [ 18.215346] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 1 timing SD-HS(SDR25) dt B [ 18.225736] [mmc]: mclk 0xf1c2008c 0x8100000b [ 18.285675] [mmc]: sdc1 set ios: clk 50000000Hz bm PP pm ON vdd 3.3V width 4 timing SD-HS(SDR25) dt B [ 18.296021] [mmc]: mclk 0xf1c2008c 0x8140030b [ 18.357915] mmc1: new high speed SDIO card at address 0001 [ 18.364532] bcmsdh_register: Linux Kernel SDIO/MMC Driver [ 18.364575] *******************sdio init ok******************* [ 18.377207] bcm_wlan_get_oob_irq enter. [ 18.381537] gpio [359] map to virq [7] ok [ 18.388851] F1 signature OK, socitype:0x1 chip:0xa9a6 rev:0x0 pkg:0x4 [ 18.396019] dhdsdio_probe_attach: unsupported chip: 0xa9a6 [ 18.402155] dhdsdio_probe: dhdsdio_probe_attach failed [ 18.407899] bcmsdh_probe: device attach failed [ 18.412981] [ 18.412984] Dongle Host Driver, version 1.88.45.3 (r420671) [ 18.412989] Compiled in drivers/net/wireless/bcmdhd on Jun 26 2017 at 12:06:39 [ 18.428835] dhd_module_init: sdio_register_driver timeout or error [ 18.435928] gpio ap6xxx_wl_regon set val 0, act val 0 [ 18.541549] [ap6xxx]: sdio wifi power state: off [ 18.546679] =========== WLAN placed in POWER OFF ======== [ 18.546915] mmc1: card 0001 removed [ 18.546995] [mmc]: mmc not poweroff notifiy [ 18.547007] [mmc]: sdc1 set ios: clk 0Hz bm OD pm OFF vdd 3.3V width 1 timing LEGACY(SDR12) dt B [ 18.547160] [mmc]: sdc1 card_power_off start... [ 18.547166] [mmc]: sdc1 power_supply is null [ 18.547173] [mmc]: sdc1 card_power_off ok [ 18.631655] init: command 'insmod' r=-1 [ 18.636066] init: command 'insmod' r=-1 [ 18.658010] fs_mgr: swapon failed for /dev/block/zram0 [ 18.663804] init: command 'swapon_all' r=-1 [ 18.668504] init: processing action 0x58e70 (console_init) [ 18.675396] init: width = 1280 [ 18.678788] init: height = 800 [ 18.682224] init: s.st_size = 3145728 [ 18.686308] init: logo match failed!fbsize = 4096000 [ 18.718811] init: command 'console_init' r=0 [ 18.723628] init: processing action 0x55bf0 (fs) [ 18.730640] init: command 'mkdir' r=-2 [ 18.741901] init: command 'insmod' r=0 [ 18.752227] init: command 'insmod' r=0 [ 18.756491] init: command 'insmod' r=-1 [ 18.771211] init: command 'insmod' r=0 [ 18.779731] init: command 'insmod' r=0 [ 18.791739] init: command 'insmod' r=0 [ 18.803941] init: command 'insmod' r=0 [ 18.816178] init: command 'insmod' r=0 19、查找:(dhdsdio_probe_attach: unsupported chip: 0xa9a6) rootroot@rootroot-E400:~$ cd wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd/ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$ grep "unsupported chip" . -R ./dhd_sdio.c: DHD_ERROR(("%s: unsupported chip: 0xx\n", ./sbutils.c: SI_ERROR(("sb_chip2numcores: unsupported chip 0x%x\n", 匹配到二进制文件 ./dhd_sdio.o 匹配到二进制文件 ./bcmdhd.o 匹配到二进制文件 ./bcmdhd.ko 匹配到二进制文件 ./sbutils.o rootroot@rootroot-E400:~/wyb/ap6212a0_a33_sc3817r/lichee/linux-3.4/drivers/net/wireless/bcmdhd$
- 1
- 粉丝: 2576
- 资源: 463
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助