FANUC LADDER6.3升级包

README.TXT File README file for FANUC LADDER-III Copyright(C), FANUC LTD., 2000 - 2010. All Rights Reserved. This document provides the information about "FANUC LADDER-III". Please read this document before using the SOFTWARE. ------------------------------------------------------------------------------ [1] Introduction [2] Outline 2.1 FANUC LADDER-III 2.2 Operation environment [3] Activation 3.1 Starting the FANUC LADDER-III from the Windows [Programs] menu. [4] History +-------------------------------------------------------------------------------+ |* Microsoft, MS, MS-DOS are the registered trademarks of Microsoft Corporation.| |* Windows is the trademark of Microsoft Corporation. | |* Other companies, products described in this document are the (registered) | | trademarks of each companies. | +-------------------------------------------------------------------------------+ ============================================================================== [1] Introduction ============================================================================== This manual describes about "FANUC LADDER-III". As for the detailed explanation, refer to the following operator's manual for the FANUC LADDER-III. "FANUC LADDER-III OPERATOR'S MANUAL B-66234EN" Notes (1) All rights regarding "FANUC LADDER-III", including the copyright shall belong to FANUC LTD. (2) No one can use or copy any part or whole of the software or document of "FANUC LADDER-III" without a prior agreement.  ============================================================================== [2] Outline ============================================================================== 2.1 FANUC LADDER-III FANUC LADDER-III is a programming system to develop the sequence program of FANUC PMC. Main functions are shown below. - Off-Line Functions 1) Creating of ladder program 2) Ladder program difference display function 3) PMC address map function 4) Cross-reference display function 5) Printing 6) Command line execution function 7) Step sequence editing 8) Function block function 9) Multi-language PMC message creation tool 10) Checking duplicate coil 11) PMC type change and save 12) Extended symbol/comment function - On-Line Functions 1) Monitoring of ladder 2) Monitoring of signal status 3) Monitoring of PMC status 4) On-Line editing of ladder diagram 5) Signal trace, Signal analysis 6) Signal trace function 7) Mnemonic monitor function 8) Saving and restoring PMC parameter 2.2 Operation environment To use this software, the requirements indicated in the table below must be satisfied. +-------------------+----------------------------------------------------+ | Computer | IBM PC/AT COMPATIBLE | +-------------------+----------------------------------------------------+ | OS | Microsoft Windows 2000/XP/Vista/7 (Note 1)| +-------------------+----------------------------------------------------+ | CPU | Windows 2000 | | | Pentium 166MHz or more | | | Windows XP Home Edition | | | Windows XP Professional | | | Pentium II 333MHz or more | | | Windows Vista Home Basic | | | Windows Vista Home Premium | | | Windows Vista Business | | | Windows Vista Ultimate | | | Processor recommended by Microsoft | | | 1GHz or more is recommended | | | Windows 7 Professional | | | Processor recommended by Microsoft | | | 1GHz or more is recommended | +-------------------+----------------------------------------------------+ | Memory | Windows 2000 | | | 64MBytes or more | | | Windows XP Home Edition | | | Windows XP Professional | | | 128MBytes or more | | | Windows Vista Home Basic | | | 512MBytes or more | | | Windows Vista Home Premium | | | Windows Vista Business | | | Windows Vista Ultimate | | | 1GByte or more | | | Windows 7 Professional (32-bit/64-bit version) | | | 1GByte or more | +-------------------+----------------------------------------------------+ | Hard disk | 40Mbytes or more free space (Note 2)| +-------------------+----------------------------------------------------+ | Graphic adapter | VGA or higher | +-------------------+----------------------------------------------------+ | Printer | The printers added by the printers settings on | | | Windows. | +-------------------+----------------------------------------------------+ | Japanese language | Input system in conformity with MS-KANJI API | | input system | | +-------------------+----------------------------------------------------+ (Note 1) Windows XP and Windows Vista of 64-bit version are not supported. Windows 2000 Professional SP4 (Note 2) In addition, the space for storing sequence data is required.  ============================================================================== [3] Activation ============================================================================== 3.1 Starting the FANUC LADDER-III from the Windows [Programs] menu. [Operation] (1) Click the [Start] button at the Windows2000/XP/Vista/7. (2) Click the [Programs] menu of the [Start] menu. (3) Click the [FANUC LADDER-III] folder of the [Programs] menu. (4) Click the "FANUC LADDER-III" of the [FANUC LADDER-III] folder. Activate the FANUC LADDER-III and run. ========================================================================== [4] History ========================================================================== Edition 6.20 -> 6.30 TMRBF instruction cannot be used in a FB library. This problem has been corrected. In Series 30i/31i/32i-A PMC which PMC memory type is C, you cannot store ladder or cannot stop ladder when R9060.0 and R9060.1 are turned ON. This problem has been corrected. In printing cross-references, when FB instance is included in a ladder program, the wrong step number or the wrong net num