Designation: A 832/A 832M – 06
Standard Specification for
Pressure Vessel Plates, Alloy Steel, Chromium-
Molybdenum-Vanadium
1
This standard is issued under the fixed designation A 832/A 832M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification
2
covers chromium-molybdenum-
vanadium alloy steel plates intended primarily for the fabrica-
tion of welded pressure vessels.
1.2 The plates furnished under this specification are re-
quired to be normalized-and-tempered. Specification A 542/
A 542M includes coverage of the material in the quenched-
and-tempered condition.
1.3 The maximum thickness of plates furnished to this
specification is limited only by the capacity of the composition
to meet the specified property requirements. However, the
maximum thickness of plates normally furnished under this
specification is 6 in. [150 mm].
1.4 The material is intended to be suitable for fusion
welding. Welding technique is of fundamental importance and
it is presupposed that welding procedures will be in accordance
with approved methods.
1.5 This specification is expressed in both inch-pound units
and in SI units. However, unless the order specifies the
applicable “M” specification designation (SI units), the mate-
rial shall be furnished to inch-pound units.
1.6 The values stated in either inch-pound units or SI units
are to be regarded separately as standard. Within the text, the
SI units are shown in brackets. The values stated in each
system must be used independently of the other. Combining
values from the two systems may result in nonconformance
with the specification.
2. Referenced Documents
2.1 ASTM Standards:
3
A 20/A 20M Specification for General Requirements for
Steel Plates for Pressure Vessels
A 370 Test Methods and Definitions for Mechanical Testing
of Steel Products
A 435/A 435M Specification for Straight-Beam Ultrasonic
Examination of Steel Plates
A 577/A 577M Specification for Ultrasonic Angle-Beam
Examination of Steel Plates
A 578/A 578M Specification for Straight-Beam Ultrasonic
Examination of Plain and Clad Steel Plates for Special
Applications
3. General Requirements and Ordering Information
3.1 Material supplied to this material specification shall
conform to Specification A 20/A 20M. These requirements
outline the testing and retesting methods and procedures,
permissible variations in dimensions, quality and repair of
defects, marking, loading, etc.
3.2 Specification A 20/A 20M establishes the rules for or-
dering information that should be complied with when pur-
chasing material to this specification.
3.3 In addition to the basic requirements of this specifica-
tion, certain supplementary requirements are available when
additional control, testing, or examination is required to meet
end use requirements. These include the following:
3.3.1 Vacuum treatment,
3.3.2 Additional or special tension testing,
3.3.3 Impact testing, and
3.3.4 Nondestructive examination.
3.4 The purchaser is referred to the listed supplementary
requirements in this specification and to the detailed require-
ments in Specification A 20/A 20M. If the requirements of this
specification are in conflict with the requirements of Specifi-
cation A 20/A 20M, the requirements of this specification shall
prevail.
4. Manufacture
4.1 Steelmaking Process—The steel shall be made by one of
the processes permitted in Specification A 20/A 20M.
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel, and Related Alloys and is the direct responsibility of Subcommittee
A01.11 on Steel Plates for Boilers and Pressure Vessels.
Current edition approved March 1, 2006. Published March 2006. Originally
approved in 1984. Last previous edition approved in 2004 as A 832/A832M – 99
(2004)
e1
.
2
For ASME Boiler and Pressure Vessel Code applications, see related Specifi-
cation SA-832/SA-832M in Section II of that Code.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
1
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
Copyright by ASTM Int'l (all rights reserved);
Reproduction authorized per License Agreement with Monique Tyree (ASTMIHS Account); Tue Mar 14 10:46:40 EST 2006
Copyright ASTM International
Provided by IHS under license with ASTM
Not for Resale
No reproduction or networking permitted without license from IHS
--`,,```,,,,````-`-`,,`,,`,`,,`---
资源评论
std86021
- 粉丝: 108
- 资源: 2835
最新资源
- Python项目-自动办公-02 批量生成PPT版荣誉证书.zip
- 2025年十大战略技术趋势-Gartner-2024-27页.pdf
- tsn-imagenet-pretrained-r50-8xb32-1x1x8-100e-kinetics400-rgb-20220906-2692d16c.pth
- Python项目-实例-21 音乐播放器.zip
- 2010-2023年中国地级市绿色金融试点DID数据
- dpdk源码，高性能的网络驱动
- tsn-imagenet-pretrained-r50-8xb32-dense-1x1x5-100e-kinetics400-rgb-20220906-dcbc6e01.pth
- 对matplotlib进行介绍
- cmake-3.30.5.tar.gz
- 有监督的学习-线性回归.ipynb
资源上传下载、课程学习等过程中有任何疑问或建议，欢迎提出宝贵意见哦~我们会及时处理！
点击此处反馈
