- 1 -
- 2 -
南 方 某 城 市 办 公 楼 设 计
摘 要 : 本课题为南方某城市办公大楼的设计,总建筑面积3990㎡左右,建筑层数四层,
一层层高4.55m,二至四层层高均为3.6m,长65.70m,宽15.2m,高15.6m。该楼由三大功
能区组成:会议室、市级领导办公室及其他配套设施,建筑设计交通流畅,各类房间满足
使用要求,体形、立面美观。采用钢筋混凝土框架结构体系,基础为柱下独立基础。该办
公楼建筑耐久等级为Ⅱ级,防火等级为Ⅰ级,抗震设防烈度七度(设计基本地震加速度为
0.10g),设计地震分组为第一组,建筑场地类别为二类场地土,地基持力层为粉质粘土土
层,持力层地基承载力特征值
aak
kPf 200�
,基础埋深定为1.50m,无软弱下卧层,不考虑
地下水影响。基本风压:0.35kN/㎡,基本雪压:0.50kN/㎡,最大降雨量60mm/h。
在认真贯彻“适用、安全、经济、美观”的原则下,研究收集各种办公楼设计方案。
设计时根据办公楼设计规范和其它相关标准,以及设计要求和提供的地质资料,按照先建
筑后结构,先整体布局后局部结点设计步骤设计。首先,根据设计出的建筑方案及所选用
的建筑材料及做法,确定结构计算简图,进行荷载和内力计算,绘制了相应的内力图;其
次,进行结构内力组合,确定结构控制截面的弯矩、剪力和轴力设计值。最后,根据已经
计算出的结构控制截面的内力值,对梁、板、柱、基础等进行配筋计算,并绘制了相应的
结构施工图。同时,采用PKPM软件进行验算,以保证计算结果的可靠性,并达到同手算
结果对比分析的目的。
关 键 词 : 框 架 结 构 荷 载 计 算 内 力 计 算 配 筋
- 3 -
An office building of south city
Abstract: This topic for an office building of anyang city of design, with a total
construction area of 4,994 square meters, four layer (layer construction layer),
placing local high 4.20 m, two to six layer are tall, long 65.70mm, 3.6 mm,
width 15.20m, high 15.60 m. By three functions: put rooms, municipal leaders
office and other facilities, building design, smooth traffic meets the requirement
of each room, beautiful shape, facade. Using reinforced concrete frame structure,
the foundation for independent foundation under column. The office building 2
level for durable, fireproof rank for 1 level, seismic fortification intensity seven
degrees (design basic earthquake acceleration 0.10 g), design for the first group,
the earthquake groups for the second site construction site, soil type, soil
foundation bearing ZhongSha for bearing characteristic value of subgrade
bearing capacity, the basis for the buried depth, under the weak 1.20 m, don't
consider layer groundwater effect, Basic wind 0.35kN/square meters, 0.50: basic
snow kN/square: usd pressure.
In conscientiously implement the "apply, safety, economy, beautiful"
principle, design of building research collection. When the design according to
the building design specification and other related standards and design
requirements and provide information, according to the geological structure
building, overall layout design steps after local node design. Firstly, according
to the design of the building plan and selected and building materials, structural
calculation, load and internal force diagram, the corresponding internal drawing,
Secondly, the internal structure, control section structure moment, shear and
axial force on the design value. Finally, according to the structure has been
calculated value of internal control section of beam, plate, column, etc, and
reinforcement of the corresponding structure construction. At the same time, the
paper adopts PKPM software available to ensure the calculation results, the
reliability, and achieve the result is compared with the hand of analysis.
Keywords: Frame internal force calculation load calculation reinforement
- 4 -
引 言
毕业设计是大学本科教育培养目标实现的重要阶段,是毕业前的综合学习阶段,是深
化、拓宽、综合教和学的重要过程,是对大学期间所学专业知识的全面总结。
本组毕业设计题目为《南方某城市办公楼设计》。在毕设前期,我温习了《结构力
学》、《钢筋混凝土》、《工程结构抗震设计》等知识,并借阅了《混凝土规范》、《荷载规
范》、《建筑设计规范》等规范。在毕设中期,我们通过所学的基本理论、专业知识和基本
技能进行建筑、结构设计,本组在校成员齐心协力、分工合作,发挥了大家的团队精神。
在毕设后期,主要进行设计手稿的整理,并用电脑绘图并得到老师的审批和指正,使我圆
满的完成了任务,在此表示衷心的感谢。
毕业设计的三个月里,在指导老师的帮助下,经过资料查阅、设计计算、论文撰写以
及外文的翻译,加深了对新规范、规程、手册等相关内容的理解。巩固了专业知识、提高
了综合分析、解决问题的能力。在绘图时熟练掌握了 AutoCAD,天正,及 PKPM 以上所有这
些从不同方面达到了毕业设计的目的与要求。
框架结构设计的计算工作量很大,在计算过程中以手算为主,辅以一些计算软件的校
正。由于自己水平有限,难免有不妥和疏忽之处,敬请各位老师批评指正。
二零一一年五月二十日
- 5 -
第一章 建筑设计说明部分
1.1 工程概况
本建筑位于南方某市办公楼,四层现浇钢筋混凝土框架结构,房间开间 4.8 米,层
高 3.6 米。65.7 米,宽 15.2 米,高 15.6 米。总建筑面积 3990 平方米。
1.2 设计资料
1.2.1 本建筑设计使用年限为 50 年.
1.2.2 耐火等级为 2 级.
1.2.3 基本风压
0
w
=0.35kN/m
2
,基本雪压
0
s
=0.5 kN/m
2
.
1.2.4 最大降雨量 60mm/h
1.2.5 抗震设防烈度为 7 度;设计基本地震加速度为 0.10g,设计地震分组为第一组,建
筑场地类别为Ⅱ类,建筑抗震设防类别为丙类.
1.3 总平面设计
1.3.1 应根据一栋楼或一个建筑群的组成和使用功能,结合所处位置和用地条件、有关技
术要求,综合研究新建的、原有的建筑物、构筑物和各项设施等相互之间的平面和空间关
系,充分利用土地,合理进行总体布局,使场地内各组成部分成为有机的整体,并与周围
环境相协调而进行的设计。
1.3.2 应结合地形、地质、气象条件等自然条件布置,有效组织地面排水,进行用地范围
内的竖向布置。
1.3.3 建筑物的布置应符合防火、卫生等规范及各种安全要求,并应满足交通要求。
1.3.4 建筑物周围布置应与城市主干道及周围环境相协调,合理组织场地内的各种交通流
线(含人流、车流、货流等),并安排好道路、出入口,并考虑风向及人员出入的便利。
1.4 主要房间设计
主要房间是各类建筑的主要部分,是供人们办公的必要房间,由于建筑物的类别不
同,使用功能不同,对主要房间的设计也不同。但主要房间设计应考虑的基本因素仍然是
一致的,即要求有适宜的尺寸,足够的使用面积,适用的形状,良好的采光和通风条件,
方便的内外交通联系,合理的结构布置和便于施工等。
因此,本建筑的柱网横向尺寸 6m+2.7m+6m,纵向尺寸 4.8m。