没有合适的资源?快使用搜索试试~ 我知道了~
基于ARM的PCI总线通信功能设计.doc
1.该资源内容由用户上传,如若侵权请联系客服进行举报
2.虚拟产品一经售出概不退款(资源遇到问题,请及时私信上传者)
2.虚拟产品一经售出概不退款(资源遇到问题,请及时私信上传者)
版权申诉
0 下载量 48 浏览量
2023-06-19
20:59:39
上传
评论
收藏 1.39MB DOC 举报
温馨提示
试读
34页
基于ARM的PCI总线通信功能设计.doc
资源推荐
资源详情
资源评论
院(系):
年 月 日
摘要
本文详细介绍了基于 AT91RM9200 单片机的 PCI 总线通信功能的设计,包括硬件设计
和软件设计两部分。通信功能的设计着重于单片机与上位机之间通过 PCI 总线进行的数据
传送。本次设计在于用比较容易掌握的单片机来实现 PCI 控制器的功能,在 PCI 总线的简
单运用场合,这样就大大简化了设计的复杂程度。设计的实现是利用单片机的 I/O 口与
PCI 总线的控制信号线以及地址/数据信号线等直接相连,用对单片机的编程来控制
数据的传输。文中介绍了 PCI 总线的基本概念,一些重要信号的定义,以及 PCI 总
线事务的时序。单片机部分介绍了型号的选择,选择了 AT91RM9200 单片机的理由和
AT91RM9200 单片机的基本知识。本次设计选择 AM29LV160 和 57V561620 作为 AT91RM9200
外接存储器。设计的结果是成功的完成了原理图绘制和 PCB 版图的设计,和实验仿真。
关键词:PCI 总线 单片机
Abstract
This paper introduces in detail the communication function design of the PCI
bus based on AT91RM9200 MCU, including hardware design and software design.
Communication function design focuses on the data transfer between SCM and PC by
PCI bus. The design is to use MCU to realize the function of PCI controller,which
is easier to master. In the simple use of the PCI bus, this design will greatly
simplify the complexity. The realization of the design is to make the I/O port
of MCU directly connected with the control and address/data signal lines of the
PCI bus. It controls the data transmission by programming MCU. This paper
introduces the basic concept of PCI bus, some important signals, and the definition
of the timing PCI bus affairs. This article at first introduces the choice of
microcontroller model, and then introduces the reason that AT91RM9200 is selected
and the basic knowledge of AT91RM9200. I choose AM29LV160HY and 57V561620 as the
memory of AT91RM9200. The result of the design is completing the drawing of
schematic diagram, the design of PCB layout and simulation.
Key words: PCI bus; MCU
目录
第一章 绪论 .................................................................1
1.1 引言 ................................................................1
1.2 设计方案 ............................................................2
1.2.1 设计框图 .......................................................2
1.2.2 设计要求 .......................................................2
第二章 器件相关知识........................................................3
2.1 PCI 总线 ............................................................3
2.1.1 PCI 总线的基本概念 ............................................3
2.1.2 PCI 总线的主要性能 ............................................4
2.1.3 PCI 总线的特点 ................................................4
2.1.4 PCI 总线的部分信号定义........................................5
2.1.5 PCI 总线事务的时序 ............................................8
2.2 单片机 ..............................................................9
2.2.1 单片机芯片型号的选择 .........................................9
2.2.2 AT91RM9200 芯片简介 ...........................................9
2.2.3 AT91RM9200 的主要模块及存储器的选择 ...........................10
第三章 硬件设计部分 ........................................................11
3.1 原理图的绘制 .......................................................11
3.1.1 AT91RM9200 ....................................................11
3.1.2 AT91RM9200 单片机所需电路 .....................................12
3.1.3 HY57V561620 ...................................................15
3.1.4 AM29LV160 .....................................................16
3.1.5 PCI 总线 ......................................................17
3.2 PCB 版图设计 ........................................................17
3.2.1 元件的封装 ....................................................17
3.2.2 PCB 版图设计 ..................................................17
第四章 软件设计部分 ........................................................19
4.1 软件编程流程图 .....................................................19
4.2 单片机初始化过程 ...................................................19
4.2.1 Boot Loader 流程 ..............................................20
4.2.2 Boot Loader 各个子流程阐述 ....................................20
第五章 软件仿真与实验 ......................................................23
第六章 设计总结 ............................................................25
致谢 .......................................................................26
参考文献 ...................................................................27
附录 A .....................................................................28
附录 B .....................................................................29
附录 C .....................................................................30
剩余33页未读,继续阅读
资源评论
oligaga
- 粉丝: 52
- 资源: 2万+
下载权益
C知道特权
VIP文章
课程特权
开通VIP
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功