没有合适的资源?快使用搜索试试~ 我知道了~
IEEE 488.2 Controller Chip
资源详情
资源评论
资源推荐
IEEE 488.2 Controller Chip
Description
The NAT9914 IEEE 488.2 controller chip can perform all the
interface functions defined by the IEEE Standard 488.1-1987,
and
also meets the additional requirements and recommendations
of the IEEE Standard 488.2-1987. Connected between the
processor and the IEEE 488 bus, the NAT9914 provides high-
level management of the IEEE 488 bus, significantly increases
the throughput of driver software, and simplifies both the
hardware and software design. The NAT9914 performs
complete IEEE 488 Talker, Listener, and Controller functions. In
addition to its numerous improvements, the NAT9914 is also
completely pin compatible with the TI TMS 9914A and
software compatible with the NEC µPD7210 and TI TMS9914A
controller chips.
IEEE 488.2 Overview
The IEEE 488.2 standard removes the ambiguities of IEEE 488.1
by standardizing the way instruments and controllers operate. It
defines data formats, status reporting, error handling, and
common configuration commands to which all IEEE 488.2
instruments must respond in a precise manner. It also defines a
set of controller requirements. With IEEE 488.2, you gain the
benefits of reduced development time and cost because systems
are more compatible and reliable. The NAT9914 brings the full
power of IEEE 488.2 to the design engineer along with
numerous other design and performance benefits, while
retaining the 40-pin and 44-pin hardware configurations of the
TI TMS 9914A.
General
The NAT9914 manages the IEEE 488 bus. You program the
IEEE 488 bus by writing control words into the appropriate
registers. CPU-readable status registers supply operational
feedback. The NAT9914 mode determines the function of
these registers. On power up or reset, the NAT9914 registers
resemble those of the TMS9914A set, with additional registers that
supply extra functionality and IEEE 488.2 compatibility. In this
mode, the NAT9914 is completely pin compatible with
the TI TMS9914A. If you enable the 7210 mode, the registers
resemble those of the NEC µPD7210 set, with additional registers
that supply extra functionality and IEEE 488.2 compatibility. This
mode is not pin compatible with the NECµPD7210. Figure 4
shows the key components of the NAT9914.
NAT9914
Pin compatible with TI TMS9914A
Software compatible with
NEC µPD7210 or TI TMS9914A
controller chips
Low power consumption
Meets all IEEE 488.2 requirements
Bus line monitoring
Preferred implementation of
requesting service
Will not send messages when there
are no Listeners
Performs all IEEE 488.1
interface functions
Programmable data transfer rate
(T1 delays of 350 ns, 500 ns,
1.1 µs, and 2 µs)
Automatic EOS and/or NL message
detection
Direct memory access (DMA)
Automatically processes IEEE 488
commands and reads
undefined commands
TTL-compatible CMOS device
Programmable clock rate
20 MHz maximum
Reduces driver overhead
Does not lose a data byte
if ATN is asserted while
transmitting data
ni.com/store
kim5233
- 粉丝: 0
- 资源: 2
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功
评论0