没有合适的资源?快使用搜索试试~ 我知道了~
ABB伺服驱动器-MicroFlex-e190-快速安装指南MFE190-04UP.pdf
1.该资源内容由用户上传,如若侵权请联系客服进行举报
2.虚拟产品一经售出概不退款(资源遇到问题,请及时私信上传者)
2.虚拟产品一经售出概不退款(资源遇到问题,请及时私信上传者)
版权申诉
0 下载量 120 浏览量
2024-04-26
12:51:29
上传
评论
收藏 2.47MB PDF 举报
温馨提示
试读
20页
ABB伺服驱动器_MicroFlex_e190_快速安装指南MFE190-04UP
资源推荐
资源详情
资源评论
List of related manuals in English
You can find manuals and other product documents in PDF format on the Internet. See section
Document library on the Internet on the inside of the back cover. For manuals not available in the
Document library, contact your local ABB representative.
* MicroFlex e190 firmware build version that supports the option card: Build 5900.4.0 and later.
3AXD50000037325 Rev D
MUL
EFFECTIVE: 2020-03-06
© 2020 ABB Beijing Drive System Co., Ltd. All Rights Reserved.
Drive hardware manuals and guides Code (English)
MicroFlex e190 User’s manual 3AXD50000037326
MicroFlex e190 Wall chart 3AXD50000037323
Certificates
MicroFlex e190 & OPT-SIO-1
EU Single Declaration of Conformity 3AXD10000540159
MicroFlex e190 STO (TÜV) Certificate 3AXD10000540318
MicroFlex e190 UL Certificate 3AXD10000540319
Option manuals and guides
OPT-MF-200 Encoder Breakout Quick installation guide 3AXD10000692233
OPT-MF-201 Resolver Adapter Quick installation guide 3AXD10000688314
OPT-SIO-1 Option Card* User's manual 3AXD50000351336
OPT-SIO-1 Option Card Quick installation guide 3AXD50000296361
Quick installation guide - MicroFlex e190
3
Quick installation guide -
MicroFlex e190
Introduction
This guide contains the very basic information
about the mechanical and electrical installation
of the MicroFlex e190 drive module. For
complete documentation see the
MicroFlex e190 User’s Manual (code:
3AXD50000037326 [English]).
Safety instructions
WARNING! All electrical
installation and maintenance work on
the drive should be carried out by
qualified electricians only.
WARNING! Operation of this
equipment requires detailed
installation and operation instructions
provided in the Installation/Operation
manual intended for use with this product. It
should be retained with this device at all times.
A hard copy of this information may be ordered
at +358 10 22 11 or your local ABB sales office.
Never work on the drive, the braking chopper
circuit, the motor cable or the motor when input
power is applied to the drive. After
disconnecting input power, always wait for 5
minutes to let the intermediate circuit
capacitors discharge before you start working
on the drive, control cabling, motor or motor
cable. Even when input power is not applied to
the drive, externally supplied control circuits
may carry dangerous voltages. Always ensure
by measuring that no voltage is actually
present.
• A rotating permanent magnet motor can
generate a dangerous voltage. Lock the
motor shaft mechanically before connecting
a permanent magnet motor to the drive, and
before doing any work on a drive system
connected to a permanent magnet motor.
• The MicroFlex e190 is an IP20 (UL open
type) drive to be used in a heated, indoor
controlled environment. The drive must be
installed in clean air according to enclosure
classification. Cooling air must be clean, free
from corrosive materials and electrically
conductive dust. See the User’s Manual for
detailed specifications.
• The MicroFlex e190 must be installed where
the pollution degree according to UL and EN
61800-5-1 shall not exceed 2.
• The maximum ambient air temperature is:
1.6 A model
: 45 °C (113 °F) at rated current.
The current is derated for 45 to 50 °C (113 to
122 °F). See user’s manual.
3 A - 9 A models
: 55 °C (131 °F) at rated
current. No current derating is required.
• Motor overtemperature sensing is not
provided by the drive.
• The drive is suitable for use in a circuit
capable of delivering not more than 5,000
rms symmetrical amperes, 240 V maximum,
when protected by CC class fuses, rated
max. 20 A.
• The cables located within the motor circuit
must be rated for at least 75 °C (167 °F) in
UL-compliant installations.
• Use 75 °C copper wiring only.
• The input cable must be protected with
fuses. Suitable IEC (class gG) and UL (class
CC) fuses are listed in the Technical data
section of the MicroFlex e190 User’s
Manual.
• Integral solid state short circuit protection
does not provide branch circuit protection.
For installation in the United States, branch
circuit protection must be provided in
accordance with the National Electrical Code
(NEC) and any applicable local codes. To
fulfill this requirement, use the UL classified
fuses.
Quick installation guide - MicroFlex e190
4
• For installation in Canada, branch circuit
protection must be provided in accordance
with Canadian Electrical Code and any
applicable provincial codes. To fulfill this
requirement, use the UL classified fuses.
• For use in Canada: Transient surge
suppression shall be installed on the line side
of this equipment and shall be rated 240 V
(phase to ground), 240 V (phase to phase),
suitable for overvoltage category III, and
shall provide protection for a rated impulse
withstand voltage peak of 2.5 kV.
• The drive provides overload protection in
accordance with the National Electrical Code
(NEC). See the User’s Manual for overload
protection settings.
• The drive can provide an overload current of
300% of rated current for a maximum of 3 s.
See user manual.
Mechanical installation
Fasten the drive module to the mounting base
using screws through the two mounting holes.
剩余19页未读,继续阅读
资源评论
AAA_自动化工程师
- 粉丝: 6033
- 资源: 3349
下载权益
C知道特权
VIP文章
课程特权
开通VIP
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功