没有合适的资源?快使用搜索试试~ 我知道了~
mdss-dsi 高通平台触摸屏lcd调试
资源推荐
资源详情
资源评论
Qualcomm mdss-dsi
mdss-dsi is the master DSI device which supports multiple DSI host controllers that
are compatible with MIPI display serial interface specification.
Required properties:
- compatible: Must be "qcom,mdss-dsi"
- hw-config: Specifies the DSI host setup configuration
"hw-config" = "single_dsi"
"hw-config" = "dual_dsi"
"hw-config" = "split_dsi"
- ranges: The standard property which specifies the child address
space, parent address space and the length.
- vdda-supply: Phandle for vreg regulator device node.
Bus Scaling Data:
- qcom,msm-bus,name: String property describing MDSS client.
- qcom, msm-bus,num-cases: This is the number of bus scaling use cases
defined in the vectors property. This must be
set to <2> for MDSS DSI driver where use-case 0
is used to remove BW votes from the system. Use
case 1 is used to generate bandwidth requestes
when sending command packets.
- qcom,msm-bus,num-paths: This represents number of paths in each bus
scaling usecase. This value depends on number of
AXI master ports dedicated to MDSS for
particular chipset.
- qcom,msm-bus,vectors-KBps: A series of 4 cell properties, with a format
of (src, dst, ab, ib) which is defined at
Documentation/devicetree/bindings/arm/msm/msm_bus.txt.
mdss-dsi is the master DSI device which supports multiple DSI host controllers that
are compatible with MIPI display serial interface specification.
Required properties:
- compatible: Must be "qcom,mdss-dsi"
- hw-config: Specifies the DSI host setup configuration
"hw-config" = "single_dsi"
"hw-config" = "dual_dsi"
"hw-config" = "split_dsi"
- ranges: The standard property which specifies the child address
space, parent address space and the length.
- vdda-supply: Phandle for vreg regulator device node.
Bus Scaling Data:
- qcom,msm-bus,name: String property describing MDSS client.
- qcom, msm-bus,num-cases: This is the number of bus scaling use cases
defined in the vectors property. This must be
set to <2> for MDSS DSI driver where use-case 0
is used to remove BW votes from the system. Use
case 1 is used to generate bandwidth requestes
when sending command packets.
- qcom,msm-bus,num-paths: This represents number of paths in each bus
scaling usecase. This value depends on number of
AXI master ports dedicated to MDSS for
particular chipset.
- qcom,msm-bus,vectors-KBps: A series of 4 cell properties, with a format
of (src, dst, ab, ib) which is defined at
Documentation/devicetree/bindings/arm/msm/msm_bus.txt.
DSI driver should always set average bandwidth
(ab) to 0 and always use instantaneous
bandwidth(ib) values.
Optional properties:
- vcca-supply: Phandle for vcca regulator device node.
- qcom,<type>-supply-entries: A node that lists the elements of the supply used by the
a particular "type" of DSI modulee. The module "types"
can be "core", "ctrl", and "phy". Within the same type,
there can be more than one instance of this binding,
in which case the entry would be appended with the
supply entry index.
e.g. qcom,ctrl-supply-entry@0
-- qcom,supply-name: name of the supply (vdd/vdda/vddio)
-- qcom,supply-min-voltage: minimum voltage level (uV)
-- qcom,supply-max-voltage: maximum voltage level (uV)
-- qcom,supply-enable-load: load drawn (uA) from enabled supply
-- qcom,supply-disable-load: load drawn (uA) from disabled supply
-- qcom,supply-pre-on-sleep: time to sleep (ms) before turning on
-- qcom,supply-post-on-sleep: time to sleep (ms) after turning on
-- qcom,supply-pre-off-sleep: time to sleep (ms) before turning off
-- qcom,supply-post-off-sleep: time to sleep (ms) after turning off
- pll-src-config Specified the source PLL for the DSI
link clocks:
"PLL0" - Clocks sourced out of DSI PLL0
"PLL1" - Clocks sourced out of DSI PLL1
This property is only valid for
certain DSI hardware configurations
mentioned in the "hw-config" binding above.
For example, in split_dsi config, the clocks can
(ab) to 0 and always use instantaneous
bandwidth(ib) values.
Optional properties:
- vcca-supply: Phandle for vcca regulator device node.
- qcom,<type>-supply-entries: A node that lists the elements of the supply used by the
a particular "type" of DSI modulee. The module "types"
can be "core", "ctrl", and "phy". Within the same type,
there can be more than one instance of this binding,
in which case the entry would be appended with the
supply entry index.
e.g. qcom,ctrl-supply-entry@0
-- qcom,supply-name: name of the supply (vdd/vdda/vddio)
-- qcom,supply-min-voltage: minimum voltage level (uV)
-- qcom,supply-max-voltage: maximum voltage level (uV)
-- qcom,supply-enable-load: load drawn (uA) from enabled supply
-- qcom,supply-disable-load: load drawn (uA) from disabled supply
-- qcom,supply-pre-on-sleep: time to sleep (ms) before turning on
-- qcom,supply-post-on-sleep: time to sleep (ms) after turning on
-- qcom,supply-pre-off-sleep: time to sleep (ms) before turning off
-- qcom,supply-post-off-sleep: time to sleep (ms) after turning off
- pll-src-config Specified the source PLL for the DSI
link clocks:
"PLL0" - Clocks sourced out of DSI PLL0
"PLL1" - Clocks sourced out of DSI PLL1
This property is only valid for
certain DSI hardware configurations
mentioned in the "hw-config" binding above.
For example, in split_dsi config, the clocks can
剩余8页未读,继续阅读
资源评论
是是是是是是是是是是是
- 粉丝: 2
- 资源: 5
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
最新资源
- 基于python+flask+mysql实现的豆瓣电影可视化系统源代码+数据库(高分项目).zip
- 基于pytorch卷积神经网络算法识别猫狗图片项目源码+模型+数据集+使用说明.zip
- 基于C++ QT实现的学生信息管理系统源码+项目说明.zip
- IMG20240425152027.jpg
- 点这里下载真实好友等1个文件.rar.zip
- 基于tensorflow同态加密的联邦学习安全聚合系统源码+运行说明.zip
- 七彩祥云丶看的的好运连连
- 土石方工程采用“南方cass”软件计算工程量的.doc
- mmexport1922918815783c336136a3e10a1bae88_1715378948463.png
- 基于51单片机的室内甲醛测试系统.doc
资源上传下载、课程学习等过程中有任何疑问或建议,欢迎提出宝贵意见哦~我们会及时处理!
点击此处反馈
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功