基于STM32单片机的433M无线传输芯片CC1101驱动源码.zip

/** @page GPIO_IOToggle GPIO_IOToggle @verbatim ******************** (C) COPYRIGHT 2010 STMicroelectronics ******************* * @file GPIO/IOToggle/readme.txt * @author MCD Application Team * @version V3.4.0 * @date 10/15/2010 * @brief Description of the GPIO IOToggle Example. ****************************************************************************** * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. ****************************************************************************** @endverbatim @par Example Description This example describes how to use GPIO BSRR (Port bit set/reset register) and BRR (Port bit reset register) for IO toggling. These registers allow modifying only one or several GPIO pins in a single atomic write access. Four LEDs are toggled in an infinite loop. @par Directory contents - GPIO/IOToggle/stm32f10x_conf.h Library Configuration file - GPIO/IOToggle/stm32f10x_it.c Interrupt handlers - GPIO/IOToggle/stm32f10x_it.h Header for stm32f10x_it.c - GPIO/IOToggle/main.c Main program - GPIO/IOToggle/system_stm32f10x.c STM32F10x system source file @par Hardware and Software environment - This example runs on STM32F10x Connectivity line, High-Density, High-Density Value line, Medium-Density, XL-Density, Medium-Density Value line, Low-Density and Low-Density Value line Devices. - This example has been tested with STMicroelectronics STM32100E-EVAL (High-Density Value line), STM32100B-EVAL (Medium-Density Value line), STM3210C-EVAL (Connectivity line), STM3210E-EVAL (High-Density and XL-Density) and STM3210B-EVAL (Medium-Density) evaluation boards and can be easily tailored to any other supported device and development board. To select the STMicroelectronics evaluation board used to run the example, uncomment the corresponding line in stm32_eval.h file (under Utilities\STM32_EVAL) - STM32100E-EVAL Set-up - Use LED1, LED2, LED3 and LED4 connected respectively to PF.06, PF.07, PF.08 and PF.09 pins - STM32100B-EVAL Set-up - Use LED1, LED2, LED3 and LED4 connected respectively to PC.06, PC.07, PC.08 and PC.09 pins - STM3210C-EVAL Set-up - Use LED1, LED2, LED3 and LED4 connected respectively to PD.07, PD.13, PF.03 and PD.04 pins - STM3210E-EVAL Set-up - Use LED1, LED2, LED3 and LED4 connected respectively to PF.06, PF0.7, PF.08 and PF.09 pins - STM3210B-EVAL Set-up - Use LED1, LED2, LED3 and LED4 connected respectively to PC.06, PC.07, PC.08 and PC.09 pins @par How to use it ? In order to make the program work, you must do the following: - Create a project and setup all project configuration - Add the required Library files: - stm32f10x_gpio.c - stm32f10x_exti.c - stm32f10x_rcc.c - stm32f10x_usart.c - misc.c - stm32f10x_i2c.c - stm32f10x_spi.c - stm32_eval.c (under Utilities\STM32_EVAL) - Edit stm32f10x.h file to select the device you are working on. - Edit stm32_eval.h file to select the evaluation board you will use. @b Tip: You can tailor the provided project template to run this example, for more details please refer to "stm32f10x_stdperiph_lib_um.chm" user manual; select "Peripheral Examples" then follow the instructions provided in "How to proceed" section. - Link all compiled files and load your image into target memory - Run the example @note - Low-density Value line devices are STM32F100xx microcontrollers where the Flash memory density ranges between 16 and 32 Kbytes. - Low-density devices are STM32F101xx, STM32F102xx and STM32F103xx microcontrollers where the Flash memory density ranges between 16 and 32 Kbytes. - Medium-density Value line devices are STM32F100xx microcontrollers where the Flash memory density ranges between 64 and 128 Kbytes. - Medium-density devices are STM32F101xx, STM32F102xx and STM32F103xx microcontrollers where the Flash memory density ranges between 64 and 128 Kbytes. - High-density Value line devices are STM32F100xx microcontrollers where the Flash memory density ranges between 256 and 512 Kbytes. - High-density devices are STM32F101xx and STM32F103xx microcontrollers where the Flash memory density ranges between 256 and 512 Kbytes. - XL-density devices are STM32F101xx and STM32F103xx microcontrollers where the Flash memory density ranges between 512 and 1024 Kbytes. - Connectivity line devices are STM32F105xx and STM32F107xx microcontrollers. * <h3><center>&copy; COPYRIGHT 2010 STMicroelectronics</center></h3> */