上节课回顾与补充
什么是电子器件?
1.1 电阻器的作用
1.2 电阻器的基本概念
1.3电路中电阻器的图形表示
(欧、美)
1.4电阻器的分类
1.5 规格:阻值、公差和额定功率
1,关于E系列电阻值的计算:
standardized values
计算公式如下:R=10^(N/E),其中,E为系列为6,12,24,48,
96,N为对E6来说去自然数0到5带入公式分别得到电阻值,E为6常
数;下一组的六个为N=6,7,8,9,10,11;依此类推;对E12来
说N分别取1到12,E为12常数;依次类推到E48,E96。
标准电阻值有E6,E12,E24,E48,E96,E192等系列,意思就是在10
以内按照比例相等的关系取N个值
这是一个几何级数问题,标称阻值的选取由以下几何级数通向表达式
表示,An=(10开k次方)n-1(次方),这是一个特殊的几何级表达式,
其公比为10开k次方,n为几何级数的项数
例如在10 以内要求有三个值, 那么k取3 ,公比为2.154按n=1,2,
3计算,得1,2.154, 4.64 取整为:1,2.2 , 4.7,如果k 取6,公比
为1.468,可得1,1.5,2.2, 3.3,4.7,6.8电阻的标称值系列,即将k分
别取为6,12,24,48,96,192化整后构成的几何数列,称为:
E6,E12,E48,E96,E192系列,分别使用于允差为20%M,
10%K,5%J,2%G,1%F,0.5%D
具体公式:
R=10^(0/6)=10^0=1;
R=10^(1/6)=10^0.16666666≈1.47;当
N=2,R=10^(2/6)=10^0.3333≈2.15;
R=10^(3/6)=10^0.5≈3.16;R =10^(4/6)=10^0.6667≈4.64
R=10^(5/6)=10^0.83333≈6.81;
R=10^(1/6)^(N-1)=(1.47)^(N-1)
E-96 电阻值
(1.024)^0≈1; (1.024)^1≈1.02 ;(1.024)^2≈1.05 ;
(1.024)^3≈1.07; (1.024)^4≈ 1.1;(1.024)^5≈1.13
E-96 电阻/电容值 1.00 1.02 1.05 1.07 1.10 1.13 1.15 1.18
1.21 1.24 1.27 1.30 1.33……..
回顾2色环表示
零欧姆的电阻:用途:代替导线连接。
Zero-ohm links are often used instead of wire links, so that
they can be inserted by a resistor-inserting machine.
A zero-ohm link or zero-ohm resistor is a wire link used
to connect traces on a printed circuit board that is
packaged in the same format as a resistor. This format
allows it to be placed on the circuit board using same
automated equipment used to place other resistors instead
of requiring a separate machine to install a jumper or other
wire.
Zero-ohm resistors may be packaged like cylindrical
resistors, or like surface-mount resistors. "000" and "0000"
sometimes appear as values on surface-mount zero-ohm
links, since these have (approximately) zero resistance.
Alternatively, a single black line may be used to denote zero
ohms using the resistor color code on a cylindrical zero-ohm
resistor.
翻译:零欧姆的连接,往往不是用电线的连接,使他们可以插入一个
电阻插入机器。
零欧姆链接或零欧姆电阻是电线连接用于连接的痕迹,对印刷电路板
是装在相同的格式,作为一个电阻器。此格式允许它被放置在电路板
使用相同的自动化设备,用于放置其他电阻器而不是要求一个单独的
机器上安装跳线或其他丝。
零欧姆电阻器,可包装一样,圆筒形电阻器,或像表面贴装电阻。 “ 0
00 ”和“ 0000 ”有时出现的价值观就表面贴装零欧姆的联系,因为这些
有(约) ,零阻力。另外,一个单一的黑线可能被用来指零欧姆电阻
器使用颜色代码在一个圆筒形零欧姆电阻器。
贴片电阻的阻值
Surface mounted resistors are printed with numerical
values in a code related to that used on axial resistors.
Standard-tolerance Surface Mount Technology (SMT)
resistors are marked with a three-digit code, in which the
?rst two digits are the ?rst two signi?cant digits of the
value and the third digit is the power of ten (the number of
zeroes)
和轴电阻器的色标类似
Resistances less than 10 ohms have 'R' to indicate the
position of the decimal point
Precision resistors are marked with a four-digit code, in
which the ?rst three digits are the signi?cant ?gures and
the fourth is the power of ten
"000" and "0000"
sometimes appear as values on surface-mount zero-ohm
links, since these have (approximately) zero resistance.
翻译:表面安装电阻器是印有数值,在一个相关的代码所用的轴流式
电阻器。标准公差表面贴装技术( SMT )处理器电阻器是一个与 3 位
代码,其中,前两个数字是前两个显着两位数的价值和第三位数字是
权力的 10 次数( 0 )
和轴电阻器的色标类似
电阻小于 10 欧姆有'表明的立场,小数点
精密电阻器是一个与 4 位代码,其中,前三个数字是显着的数字,第
四是权力 10
“ 000 ”和“ 0000 ”
有时出现的价值观就表面贴装零欧姆的联系,因为这些有(约) ,零
电阻
RC05K103JT
RC为产品代号,表示片状电阻器, 05表示型号
K表示电阻温度系数也有其它温度系数符号,F:±25;G:
±50;H:±100;K : ± 25 0;M:±500
103表示阻值
J表示电阻值误差,F:±1%;G:±25%;J:±5%;0:跨接电
阻
T表示包装,T 编带包装 ;B:塑料盒散包装
标记小结a
元件上的标注:当片式电阻阻精度为5%时,采用3个数字表示。跨接线
记为000,阻值小于10Ω,在两个数字之间补加“R”表示,阻值在10 Ω
以上的,则最后一数值表示增加的零的个数。例如4.7Ω记为4R7;
0Ω(跨接线)记为000记为101;1MΩ。
标记小结b
当片式电阻值精度为1%时,则采用4个数字表示,前面3个数字为有效
数字,第四位表示增加的零的个数;阻值小于10Ω的,仍在第二位补
加“R”,阻值为100Ω,则在第四位补“0”。例如4.7Ω记为4R70,100Ω
记为1000,1MΩ记为1004,10Ω记为10R0
0603表示的是封装尺寸 与具体阻值没有关系
0201 1/20W
0402 1/16W
0603 1/10W
0805 1/8W
1206 1/4W
2,公差也叫电阻器的容差
Resistor Tolerance is expressed as the deviation from
nominal value in percent and is measured at 25
o
C
only with no appreciable load applied. It will change
depending on the other conditions when in use.
不加负载时25oC的测量的偏差
The resistance value of the resistor is not the only thing to
consider when selecting a resistor for use in a circuit. The
“tolerance” and the electric power ratings of the resistor
are also important.
For example, a 100 ohm resistor with a tolerance of
10% can range in value from 90 ohms to 110 ohms
and this will change as power is applied and the
temperature varies.
翻译:电阻器偏差是用偏离实际值的百分数来表示,是在25oC时没有
其他应用电阻是测量的。它在使用中视乎有关的其他条件而改变。
不加负载时25oC的测量的偏差
该电阻值的电阻是不是唯一的一件事时要考虑选择一个电阻器使用在
一个电路。 “偏差”和电阻的功率也很重要。
例如,一个 100 欧姆的电阻有 10 %偏差,阻值范围从 90 欧姆到 110 欧
姆,这会随着所提供的功率和温度的变化而变化。
并且随功率和温度而变化
例如, 一只标着470欧姆的电阻器, 其实际值可能偏离标示值47欧姆,
而仍在容差范围之内, 即从423欧姆到517欧姆都是符合容差的. 容差
是按照标示值, 而不是实际值计算的.
在测量一只标着470欧姆的电阻时, 如果测量值为427欧姆, 它就在
10%的容差范围之内; 而如果测量值为420欧姆, 则它的实际值已经超
出了10%的范围, 就是一个不合格品
有些电阻器的容差小于5%. 这种精密的电阻用于对误差要求比较严格
的场合. 在大多数的音频或射频振荡器和放大器中, 10%或5%的容差
已经足够好. 在有些情况下, 甚至可以使用容差为20%的电阻器.
3,额定功率Power Rating