DS18B20+DS1302(电子实时时钟).rar_修改rtc实时时钟时间资源-CSDN文库

共15个文件

bak：2个

pwi：1个

opt：1个

DS1302

DS18B20

需积分: 9 161 浏览量 2008-10-04 16:49:33 上传评论收藏 464KB RAR 举报

资源推荐

资源详情

资源评论

收起资源包目录

DS18B20+DS1302(电子实时时钟).rar （15个子文件）

DS18B20+DS1302(电子实时时钟)

TX-1C.DSN 250KB

DS18B20_Uv2.Bak 0B

DS18B20.Uv2 2KB

DS18B20.pdf 392KB

DS18B20.hex 5KB

DS18B20 24KB

DS18B20.plg 222B

DS18B20.M51 33KB

TX-1C.PWI 1KB

DS18B20.Opt 1KB

DS18B20.LST 27KB

DS18B20.OBJ 29KB

DS18B20.c 15KB

DS18B20_Opt.Bak 1KB

Last Loaded TX-1C.DBK 250KB

1 of 27 050400

FEATURES

 Unique 1-Wire interface requires only one

port pin for communication

 Multidrop capability simplifies distributed

temperature sensing applications

 Requires no external components

 Can be powered from data line. Power supply

range is 3.0V to 5.5V

 Zero standby power required

 Measures temperatures from -55°C to

+125°C. Fahrenheit equivalent is -67°F to

+257°F

 ±0.5°C accuracy from -10°C to +85°C

 Thermometer resolution is programmable

from 9 to 12 bits

 Converts 12-bit temperature to digital word in

750 ms (max.)

 User-definable, nonvolatile temperature alarm

settings

 Alarm search command identifies and

addresses devices whose temperature is

outside of programmed limits (temperature

alarm condition)

 Applications include thermostatic controls,

industrial systems, consumer products,

thermometers, or any thermally sensitive

system

PIN ASSIGNMENT

PIN DESCRIPTION

GND - Ground

DQ - Data In/Out

- Power Supply Voltage

NC - No Connect

DESCRIPTION

The DS18B20 Digital Thermometer provides 9 to 12-bit (configurable) temperature readings which

indicate the temperature of the device.

Information is sent to/from the DS18B20 over a 1-Wire interface, so that only one wire (and ground)

needs to be connected from a central microprocessor to a DS18B20. Power for reading, writing, and

performing temperature conversions can be derived from the data line itself with no need for an external

power source.

Because each DS18B20 contains a unique silicon serial number, multiple DS18B20s can exist on the

same 1-Wire bus. This allows for placing temperature sensors in many different places. Applications

where this feature is useful include HVAC environmental controls, sensing temperatures inside buildings,

equipment or machinery, and process monitoring and control.

DS18B20

Programmable Resolution

1-Wire

Digital Thermomete

www.dalsemi.com

PRELIMINARY

DALLAS

DS1820

1 2 3

GND

VDD

1 2 3

BOTTOM VIEW

DS18B20 To-92

Package

GND

DS18B20Z

8-Pin SOIC (150 mil)

DS18B20

2 of 27

DETAILED PIN DESCRIPTION Table 1

8PIN SOIC

TO92 SYMBOL DESCRIPTION

5 1 GND Ground.

42DQData Input/Output pin. For 1-Wire operation: Open

drain. (See “Parasite Power” section.)

33V

Optional V

pin. See “Parasite Power” section for

details of connection. V

must be grounded for

operation in parasite power mode.

DS18B20Z (8-pin SOIC): All pins not specified in this table are not to be connected.

OVERVIEW

The block diagram of Figure 1 shows the major components of the DS18B20. The DS18B20 has four

main data components: 1) 64-bit lasered ROM, 2) temperature sensor, 3) nonvolatile temperature alarm

triggers TH and TL, and 4) a configuration register. The device derives its power from the 1-Wire

communication line by storing energy on an internal capacitor during periods of time when the signal line

is high and continues to operate off this power source during the low times of the 1-Wire line until it

returns high to replenish the parasite (capacitor) supply. As an alternative, the DS18B20 may also be

powered from an external 3 volt - 5.5 volt supply.

Communication to the DS18B20 is via a 1-Wire port. With the 1-Wire port, the memory and control

functions will not be available before the ROM function protocol has been established. The master must

first provide one of five ROM function commands: 1) Read ROM, 2) Match ROM, 3) Search ROM, 4)

Skip ROM, or 5) Alarm Search. These commands operate on the 64-bit lasered ROM portion of each

device and can single out a specific device if many are present on the 1-Wire line as well as indicate to

the bus master how many and what types of devices are present. After a ROM function sequence has

been successfully executed, the memory and control functions are accessible and the master may then

provide any one of the six memory and control function commands.

One control function command instructs the DS18B20 to perform a temperature measurement. The result

of this measurement will be placed in the DS18B20’s scratch-pad memory, and may be read by issuing a

memory function command which reads the contents of the scratchpad memory. The temperature alarm

triggers TH and TL consist of 1 byte EEPROM each. If the alarm search command is not applied to the

DS18B20, these registers may be used as general purpose user memory. The scratchpad also contains a

configuration byte to set the desired resolution of the temperature to digital conversion. Writing TH, TL,

and the configuration byte is done using a memory function command. Read access to these registers is

through the scratchpad. All data is read and written least significant bit first.

DS18B20

3 of 27

DS18B20 BLOCK DIAGRAM Figure 1

PARASITE POWER

The block diagram (Figure 1) shows the parasite-powered circuitry. This circuitry “steals” power

whenever the DQ or V

pins are high. DQ will provide sufficient power as long as the specified timing

and voltage requirements are met (see the section titled “1-Wire Bus System”). The advantages of

parasite power are twofold: 1) by parasiting off this pin, no local power source is needed for remote

sensing of temperature, and 2) the ROM may be read in absence of normal power.

In order for the DS18B20 to be able to perform accurate temperature conversions, sufficient power must

be provided over the DQ line when a temperature conversion is taking place. Since the operating current

of the DS18B20 is up to 1.5 mA, the DQ line will not have sufficient drive due to the 5k pullup resistor.

This problem is particularly acute if several DS18B20s are on the same DQ and attempting to convert

simultaneously.

There are two ways to assure that the DS18B20 has sufficient supply current during its active conversion

cycle. The first is to provide a strong pullup on the DQ line whenever temperature conversions or copies

to the E

memory are taking place. This may be accomplished by using a MOSFET to pull the DQ line

directly to the power supply as shown in Figure 2. The DQ line must be switched over to the strong pull-

up within 10 µs maximum after issuing any protocol that involves copying to the E

memory or initiates

temperature conversions. When using the parasite power mode, the V

pin must be tied to ground.

Another method of supplying current to the DS18B20 is through the use of an external power supply tied

to the V

pin, as shown in Figure 3. The advantage to this is that the strong pullup is not required on the

DQ line, and the bus master need not be tied up holding that line high during temperature conversions.

This allows other data traffic on the 1-Wire bus during the conversion time. In addition, any number of

DS18B20s may be placed on the 1-Wire bus, and if they all use external power, they may all

simultaneously perform temperature conversions by issuing the Skip ROM command and then issuing the

Convert T command. Note that as long as the external power supply is active, the GND pin may not be

floating.

The use of parasite power is not recommended above 100°C, since it may not be able to sustain

communications given the higher leakage currents the DS18B20 exhibits at these temperatures. For

applications in which such temperatures are likely, it is strongly recommended that V

be applied to the

DS18B20.

64-BIT ROM

AND

1-WIRE PORT

MEMORY AND

CONTROL LOGIC

SCRATCHPAD

8-BIT CRC

ENERAT

TEMPERATURE SENSOR

HIGH TEMPERATURE

TRIGGER, TH

LOW TEMPERATURE

TRIGGER, TL

CONFIGURATION

POWER

SUPPLY

SENSE

INTERNAL V

DS18B20

4 of 27

For situations where the bus master does not know whether the DS18B20s on the bus are parasite

powered or supplied with external V

, a provision is made in the DS18B20 to signal the power supply

scheme used. The bus master can determine if any DS18B20s are on the bus which require the strong

pullup by sending a Skip ROM protocol, then issuing the read power supply command. After this

command is issued, the master then issues read time slots. The DS18B20 will send back “0” on the

1-Wire bus if it is parasite powered; it will send back a “1” if it is powered from the V

pin. If the

master receives a “0,” it knows that it must supply the strong pullup on the DQ line during temperature

conversions. See “Memory Command Functions” section for more detail on this command protocol.

STRONG PULLUP FOR SUPPLYING DS18B20 DURING TEMPERATURE

CONVERSION Figure 2

USING V

TO SUPPLY TEMPERATURE CONVERSION CURRENT Figure 3

µP

+3V - +5.5V

DS18B20

GND

I/O

4.7k

µP

DS18B20

I/O

+3V - +5.5V

4.7k

EXTERNAL

+3V - +5.5V

SUPPLY

TO OTHER

1-WIRE

DEVICES

DS18B20

5 of 27

OPERATION - MEASURING TEMPERATURE

The core functionality of the DS18B20 is its direct-to-digital temperature sensor. The resolution of the

DS18B20 is configurable (9, 10, 11, or 12 bits), with 12-bit readings the factory default state. This

equates to a temperature resolution of 0.5°C, 0.25°C, 0.125°C, or 0.0625°C. Following the issuance of

the Convert T [44h] command, a temperature conversion is performed and the thermal data is stored in

the scratchpad memory in a 16-bit, sign-extended two’s complement format. The temperature

information can be retrieved over the 1-Wire interface by issuing a Read Scratchpad [BEh] command

once the conversion has been performed. The data is transferred over the 1-Wire bus, LSB first. The

MSB of the temperature register contains the “sign” (S) bit, denoting whether the temperature is positive

or negative.

Table 2 describes the exact relationship of output data to measured temperature. The table assumes 12-bit

resolution. If the DS18B20 is configured for a lower resolution, insignificant bits will contain zeros. For

Fahrenheit usage, a lookup table or conversion routine must be used.

Temperature/Data Relationships Table 2

-1

-2

-3

-4

LSB

MSb

(unit = °C)

LSb

SSSSS2

MSB

TEMPERATURE DIGITAL OUTPUT

(Binary)

DIGITAL

OUTPUT

(Hex)

+125°C 0000 0111 1101 0000 07D0h

+85°C 0000 0101 0101 0000 0550h*

+25.0625°C 0000 0001 1001 0001 0191h

+10.125°C 0000 0000 1010 0010 00A2h

+0.5°C 0000 0000 0000 1000 0008h

0°C 0000 0000 0000 0000 0000h

-0.5°C 1111 1111 1111 1000 FFF8h

-10.125°C 1111 1111 0101 1110 FF5Eh

-25.0625°C 1111 1110 0110 1111 FF6Fh

-55°C 1111 1100 1001 0000 FC90h

*The power on reset register value is +85°C.

OPERATION - ALARM SIGNALING

After the DS18B20 has performed a temperature conversion, the temperature value is compared to the

trigger values stored in TH and TL. Since these registers are 8-bit only, bits 9-12 are ignored for

comparison. The most significant bit of TH or TL directly corresponds to the sign bit of the 16-bit

temperature register. If the result of a temperature measurement is higher than TH or lower than TL, an

alarm flag inside the device is set. This flag is updated with every temperature measurement. As long as

the alarm flag is set, the DS18B20 will respond to the alarm search command. This allows many

DS18B20s to be connected in parallel doing simultaneous temperature measurements. If somewhere the

temperature exceeds the limits, the alarming device(s) can be identified and read immediately without

having to read non-alarming devices.

评论收藏

内容反馈

zhouqing1987311

粉丝: 2
资源: 10

DS18B20+DS1302(电子实时时钟).rar

DS18B20+DS1302 显示温度和时间Proteus仿真图

单片机程序（DS18B20+DS1302+12864万年历）

DS18B20+DS1302(电子实时时钟)

时钟DS18B20和DS1302

实时时钟DS1302

电子-DS1302.rar

DS1302实时时钟

基于Keil+51单片机DS1302时钟+DS18B20+无线遥控应用程序与仿真（源码+仿真）

DS1302时钟+DS18B20+LCD1602

DS1302时钟+DS18B20+无线遥控应用程序\DS1302时钟+DS18B20+无线遥控应用程序

DS18B20+DS1302+定时器组成时钟温度计

基于stm32f103的DS18B20+DS1302+LCD2004.rar

12864+DS1302+DS18B20+24C02时间温度显示

万年历设计LCD1602+DS18B20+DS1302.rar

1602+18B20+DS1302电子时钟源程序.zip_18b20_DS1302+AT89C52+1602_源程序_电子时钟

51单片机C语言设计综合实例9例包括1602+18B20电子钟12864+DS1302时钟+18B20温度计1602+24C08+4X4键盘密码锁等.zip

DS1302时钟加DS18B20温度

DS1302时钟+DS18B20

DS1302时钟+DS18B20+源程序

电子万年历DS1302、DS18B20的程序设计

DS1302时钟+DS18B20+无线遥控应

1602+18B20+DS1302电子时钟源程序.rar

DS1302+DS18B20+LCD12864

最新资源