Reference number
ISO 10110-1:2006(E)
©
ISO 2006
INTERNATIONAL
STANDARD
ISO
10110-1
Second edition
2006-07-01
Optics and photonics — Preparation
of drawings for optical elements and
systems —
Part 1:
General
Optique et photonique — Indications sur les dessins pour éléments et
systèmes optiques —
Partie 1: Généralités
ISO 10110-1:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii
© ISO 2006 – All rights reserved
ISO 10110-1:2006(E)
© ISO 2006 – All rights reserved iii
Contents Page
Foreword............................................................................................................................................................ iv
1 Scope ..................................................................................................................................................... 1
2 Normative references ........................................................................................................................... 1
3 Fundamental stipulations .................................................................................................................... 2
4 Presentation and dimensioning .......................................................................................................... 2
4.1 Views ...................................................................................................................................................... 2
4.2 Axes........................................................................................................................................................ 4
4.3 Leader lines ........................................................................................................................................... 5
4.4 Test regions........................................................................................................................................... 5
4.5 Test volumes ......................................................................................................................................... 6
4.6 Dimensioning ........................................................................................................................................ 8
4.7 Material specification ......................................................................................................................... 14
4.8 Indication of tolerances and various properties ............................................................................. 14
5 Additional indications for optical layout drawings ......................................................................... 16
5.1 General................................................................................................................................................. 16
5.2 Axial separations ................................................................................................................................ 17
5.3 Images, pupils, field stops and other apertures.............................................................................. 19
Annex A (informative) Examples of drawings of optical elements ............................................................. 21
Bibliography ..................................................................................................................................................... 24
ISO 10110-1:2006(E)
iv © ISO 2006 – All rights reserved
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10110-1 was prepared by Technical Committee ISO/TC 172, Optics and photonics, Subcommittee SC 1,
Fundamental standards.
This second edition cancels and replaces the first edition (ISO 10110-1:1996) which has been technically
revised.
ISO 10110 consists of the following parts, under the general title Optics and photonics — Preparation of
drawings for optical elements and systems:
⎯ Part 1: General
⎯ Part 2: Material imperfections — Stress birefringence
⎯ Part 3: Material imperfections — Bubbles and inclusions
⎯ Part 4: Material imperfections — Inhomogeneity and striae
⎯ Part 5: Surface form tolerances
⎯ Part 6: Centring tolerances
⎯ Part 7: Surface imperfection tolerances
⎯ Part 8: Surface texture
⎯ Part 9: Surface treatment and coating
⎯ Part 10: Table representing data of optical elements and cemented assemblies
⎯ Part 11: Non-toleranced data
⎯ Part 12: Aspheric surfaces
⎯ Part 14: Wavefront deformation tolerance
⎯ Part 17: Laser irradiation damage threshold
INTERNATIONAL STANDARD ISO 10110-1:2006(E)
© ISO 2006 – All rights reserved 1
Optics and photonics — Preparation of drawings for optical
elements and systems —
Part 1:
General
1 Scope
ISO 10110 specifies the presentation of design and functional requirements for optical elements and systems
in technical drawings used for manufacturing and inspection.
This part of ISO 10110 specifies the presentation in drawings of the characteristics, especially the tolerances,
of optical elements and systems.
Rules for preparation of technical drawings as well as for dimensioning and tolerancing are given in various
International Standards. These general standards apply to optical elements and systems only if the necessary
rules are not given in the various parts of ISO 10110.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 128-24, Technical drawings — General principles of presentation — Part 24: Lines on mechanical
engineering drawings
ISO 406, Technical drawings — Tolerancing of linear and angular dimensions
ISO 7944, Optics and optical instruments — Reference wavelengths
ISO 8015, Technical drawings — Fundamental tolerancing principle
ISO 10110-2, Optics and optical instruments — Preparation of drawings for optical elements and systems —
Part 2: Material imperfections — Stress birefringence
ISO 10110-3, Optics and optical instruments — Preparation of drawings for optical elements and systems —
Part 3: Material imperfections — Bubbles and inclusions
ISO 10110-4, Optics and optical instruments — Preparation of drawings for optical elements and systems —
Part 4: Material imperfections — Inhomogeneity and striae
ISO 10110-5:1996, Optics and optical instruments — Preparation of drawings for optical elements and
systems — Part 5: Surface form tolerances
ISO 10110-6:1996, Optics and optical instruments — Preparation of drawings for optical elements and
systems — Part 6: Centring tolerances
ISO 10110-7, Optics and optical instruments — Preparation of drawings for optical elements and systems —
Part 7: Surface imperfection tolerances
评论0