没有合适的资源?快使用搜索试试~ 我知道了~
本文档详细介绍NetApp FAS8300初始化,集群创建;aggr,卷、LUN的配置,NFS,CIFS,SAN环境的配置
资源推荐
资源详情
资源评论
Netapp 存储 安装及验收报告
NETAPP FAS8300 存储设备
安装实施报告
Netapp 存储 安装及验收报告
目录
1 设备配置信息 .................................................................................................................... 3
2 初始化集群配置 ................................................................................................................ 4
2.1 创建集群 ......................................................................................................................... 4
2.1.1 节点 1 创建集群 .................................................. 4
2.1.2
节点 2 加入集群 .................................................. 6
2.1.3
查看集群状态 .................................................... 8
2.2 配置 SP 远程控制 ........................................................................................................... 9
2.3 时间配置 ......................................................................................................................... 9
2.4 HA 配置 ............................................................................................................................ 9
3 系统详细配置 .................................................................................................................... 9
3.1 磁盘 AGGR 划分 ............................................................................................................... 9
3.1.1
存储聚合配置(aggr) ............................................ 9
3.2 创建并配置 SVM ............................................................................................................ 17
3.2.1
创建 FC 协议 SVM ................................................. 17
3.2.2
创建 NFS,CIFS 协议 SVM ........................................... 17
3.2.3
查看 SVM 状态 ................................................... 18
3.3 网络接口配置 ............................................................................................................... 19
3.3.1
配置接口广播域 ................................................. 19
3.3.2
配置接口地址 ................................................... 19
3.3.3
网关路由配置 ................................................... 23
3.4 创建卷 ........................................................................................................................... 24
3.5 创建 LUN ........................................................................................................................ 24
3.6 NFS、CIFS 访问配置 .................................................................................................... 25
3.7 创建 SAN 主机组 ........................................................................................................... 26
Netapp 存储 安装及验收报告
1 设备配置信息
集群基本配置信息
集群名称
FAS8300
集群管理端口
e0M
集群管理 IP
10.201.101.18
子网掩码
255.255.255.0
网关
10.201.104.254
管理用户名
密码
节点配置
节点序列号
节点名称
FAS8300-01
FAS8300-02
节点管理端口
e0M
e0M
节点管理地址
10..201.101.16
10..201.101.17
子网掩码
255.255.255.0
255.255.255.0
网关
10.201.104.254
10.201.104.2541
SP 配置
IP 地址
10.201.101.19
10..201.101.20
子网掩码
255.255.255.0
255.255.255.0
网关
10.201.104.254
10.201.104.254
网络端口配置
聚合端口
e0e,e0f,e0g,e0h
e0e,e0f,e0g,e0h
聚合端口名
a0a
a0a
端口聚合类型
LACP
LACP
角色
业务
业务
IP 地址
10.201.14.15
10.201.14.16
子网掩码
255.255.255.0
255.255.255.0
网关
10.201.14.254
10.201.14.254
Netapp 存储 安装及验收报告
2 初始化集群配置
2.1 创建集群
注意:以下信息是通过 console 用命令行进行存储配置时记录的实时信息,由于 console 信息较多,
只截取重要信息,部分需要手动输入的参数或命令,统一用加粗字体表示。
2.1.1 节点 1 创建集群
::> cluster setup
Welcome to the cluster setup wizard.
You can enter the following commands at any time:
"help" or "?" - if you want to have a question clarified,
"back" - if you want to change previously answered questions, and
"exit" or "quit" - if you want to quit the cluster setup wizard.
Any changes you made before quitting will be saved.
You can return to cluster setup at any time by typing "cluster setup".
To accept a default or omit a question, do not enter a value.
This system will send event messages and periodic reports to NetApp Technical Support. To
disable this feature, enter autosupport modify -support disable within 24 hours.
Enabling AutoSupport can significantly speed problem determination and resolution, should
a problem occur on your system.
For further information on AutoSupport, see:http://support.netapp.com/autosupport/
Type yes to confirm and continue {yes}: yes
Enter the node management interface port [e0M]: e0M
Enter the node management interface IP address: 输入节点管理 IP
Enter the node management interface netmask: 255.255.255.0
Enter the node management interface default gateway: 网关
A node management interface on port e0M with IP address 10.201.101.16 has been created.
Use your web browser to complete cluster setup by accessing https://10.201.101.16
Otherwise, press Enter to complete cluster setup using the command line interface: 回车
Netapp 存储 安装及验收报告
Do you want to create a new cluster or join an existing cluster? {create, join}:create
Do you intend for this node to be used as a single node cluster? {yes, no} [no]:no
Existing cluster interface configuration found:
Port MTU IP Netmask
e0c 9000 169.254.130.66 255.255.0.0
e0d 9000 169.254.105.154 255.255.0.0
Do you want to use this configuration? {yes, no} [yes]: yes
Enter the cluster administrator's (username "admin") password:
Retype the password:
Step 1 of 5: Create a Cluster
You can type "back", "exit", or "help" at any question.
Enter the cluster name: FAS8300
Creating cluster FAS8300
Starting cluster support services
Cluster FAS8300 has been created.
Step 2 of 5: Add Feature License Keys
You can type "back", "exit", or "help" at any question.
Enter an additional license key []: 回车
Step 3 of 5: Set Up a Vserver for Cluster Administration
You can type "back", "exit", or "help" at any question.
Enter the cluster management interface port: e0M
Enter the cluster management interface IP address: 输入集群管理 IP
Enter the cluster management interface netmask: 255.255.255.0
Warning: The configured failover-group has no valid failover targets for the
LIF's failover-policy. To view the failover targets for a LIF, use the
"network interface show -failover" command.
Enter the cluster management interface default gateway [10.201.101.254]:回车
A cluster management interface on port e0M with IP address 10.201.101.18 has been created.
You can use this address to connect to and manage the cluster.
剩余26页未读,继续阅读
资源评论
AIT小菜鸟
- 粉丝: 2
- 资源: 36
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功