没有合适的资源?快使用搜索试试~ 我知道了~
scsa题库, 310-200,solaris
需积分: 10 8 下载量 180 浏览量
2010-09-17
22:54:56
上传
评论
收藏 9.13MB PDF 举报
温馨提示
试读
204页
Sun Ceritificated Solaris Administrator题库
资源推荐
资源详情
资源评论
www.testinginside.com
Question: 1
Most files in the Solaris OS make use of data blocks. Which one does NOT use data
blocks for storag?
A. Directory
B. Device file
C. Regular file
D. Symbolic link
Answer: B
Question: 2
The x86 Solaris platform boots from the BIOS ROM and follows a different path than a
SPARC system would follow during the Boot PROM Phase. The x86-based system
invokes software interrupt INT 19h, Bootstrap during the boot PROM phase. Which
describes the software interrupt INT 19h, Bootstrap?
A. Boots from the master boot block on the diskette drive or the first hard disk drive.
B. Reads the first physical sector from the diskette drive, or from the first hard disk
drive. The processor then jumps to the sector image in RAM.
C. The master boot finds the active partition in the FDISK table, loads the first physical
sector from the ACTIVE partition, and boots to the master boot block.
D. Reads the first physical sector from the diskette drive, or from the first hard disk
drive. The processor then jumps to the first sector on the drive for the master boot block.
Answer: B
Question: 3
Currently, when powering on your server, it boots to the multi-user milestone by default.
You want to change that behavior so that your server boots to the single-user milestone
by default. Which describes how to change the default run level of your server so that
when the power is turned on, the system will boot into the single-user milestone and
stop?
A. svcadm milestone/single-user
B. svcadm milestone single-user:default
C. svcs -D milestone/single-user:default
D. svcadm -d milestone/single-user:default
E. svcadm enable milestone/single-user:default
310-200
2
http://www.testkiller.com
http://www.troytec.com
www.testinginside.com
Answer: D
Question: 4
The BIOS on your x86-based system has these Bohe BIOS on your x86-based system
has these Boot Device Priority settings:
First boot device [Hard Disk]
Second boot device [LAN]
Third boot device [ ]
No operating system is currently loaded on the disk and you want to install Solaris 10 on
this system. Without making any changes to the BIOS settings, which installation
method must you use?
A. Use the WAN boot installation
B. Use PXE with custom JumpStart
C. Boot from a Solaris PXE diskette
D. Solaris cannot be installed on this hardware configuration
E. Boot from a Solaris 10 Device Configuration Assistant Diskette
Answer: B
Question: 5
You manage several servers in a department with several system administrators. One of
the other system administrators setup several file system snapshots, but did not leave any
documentation about them. Which command is used to display a summary of all of the
snapshots on the system and its corresponding virtual device, as shown in the following
example?
0 /export/home
1 /usr
2 /database
A. /usr/sbin/fssnap -a
B. /usr/sbin/fssnap -i
C. usr/lib/fs/ufs/fssnap -i
D. /usr/lib/fs/ufs/fssnap -a
Answer: B
Question: 6
You are managing several servers from a remote building where you cannot physically
inspect the hardware. A new disk has been added to one of the x86-based servers. The
hardware technician provided the following information about the disk drive:
IDE secondary disk
310-200
3
http://www.testkiller.com
http://www.troytec.com
www.testinginside.com
Which corresponds to the absolute physical device pathname that Solaris assigns to that
new disk drive?
A. hd1,1
B. /dev/rdsk/c0d1s2
C. /pci@0,0/pci-ide@1f,1/ide@0/cmdk@1,0:c
D. /devices/pci@0,0/pci-ide@1f,1/ide@0/dad@1,0:c
E. /devices/pci@0,0/pci-ide@1f,1/ide@0/cmdk@1,0:c
Answer: E
Question: 7
When setting up your server, you want these network services configured on the fresh
installation of Solaris 10, before the first reboot:
Which method is used to configure these services?
A. Run the netservices limited command.
B. Boot to the multi-user milestone; Do NOT boot to the multi-user-server milestone.
C. After the first boot, use the svcadm command to disable or enable each of these
services.
D. Answer NO to enabling network services for remote clients during the installation
of the OS
Answer: D
Question: 8
You are logged into systemA and you issue these three commands:
310-200
4
http://www.testkiller.com
http://www.troytec.com
www.testinginside.com
Which two describe your access to the /export/home/test directory? (Choose two.)
A. You can delete files in this directory.
B. You can create files in this directory.
C. You can execute the file named script.
D. You can edit and save files in this directory.
E. You can create sub-directories in this directory.
Answer: C, D
Question: 9
You have an x86-based server with two SATA drives. Each drive has an installation of
Solaris for the x86 platform, and both drives are identical. The system currently boots
from the first SATA disk drive but, after modifying the /etc/vfstab file on the boot drive,
the first SATA drive will not boot. You want to boot the system from the second SATA
disk drive, but it will not boot. What do you need to do to get the system booted?
A. Boot from DVD to get into a single user shell; mount and fix the /etc/vfstab file on
the boot drive.
B. Edit the boot string in the GRUB menu to boot from the second SATA drive. Once
booted to the second drive, mount and fix the /etc/vfstab file on the boot disk.
C. Install a bootblock onto the second SATA drive, then select the second drive during
bootup. Once booted to the second drive, mount and fix the /etc/vfstab file on the boot
disk.
D. Select the second SATA drive in the GRUB menu during bootup and boot to the
310-200
5
http://www.testkiller.com
http://www.troytec.com
www.testinginside.com
econd drive. Once booted to the second drive, mount and copy the /etc/vfstab file to the
boot disk.
Answer: A
Question: 10
During the bootup of a Solaris x86-based system, when the kernel gains control of the
boot process it will initialize the CPU, memory, and I/O devices. Then, the kernel will
mount the root file (/)system on the device as specified by the bootpath property. Where
is the bootpath property stored?
A. /boot/grub/menu.lst
B. /boot/solaris/bootenv.rc
C. platform/i86pc/boot_archive
D. /boot/solaris/filelist.ramdisk
Answer: B
Question: 11
As the Solaris OS administrator in your department, you have been asked to upgrade a
SPARC-based server currently running Solaris 8 OS to the latest Solaris 10 OS release.
This server is critical to the department's productivity, so this upgrade must be done with
minimal downtime and must allow for rollback to the previous version. Which
installation method should you use?
A. Live Upgrade
B. Flash Archive
C. Custom JumpStart
D. WAN boot installation
Answer: A
Question: 12
There is a project that requires a large number of systems to be re-installed on the
network. Each installation needs to be hands off and tailored to the task for which the
system is intended. Which installation method allows for the specific tailoring of these
installs?
A. Solaris Live Upgrade software
B. Custom JumpStart Installation
310-200
6
http://www.testkiller.com
http://www.troytec.com
剩余203页未读,继续阅读
资源评论
yaozhiping
- 粉丝: 1
- 资源: 3
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功