proxmark3-pm3-基于ubuntu-20.04.1编译固件-2020-10-30 github代码库（含嗅探解密工具实...

Ubuntu Linux Fl0-0 edited this page on 3 Feb 2019 · 15 revisions Table of Contents Setup and build for UBUNTU Compiling the proxmark3 source code Plug in the Proxmark3 HID device CDC device Flashing HID Flashing CDC Running the proxmark3 client Setup and build for UBUNTU This is the instructions to build easily on Ubuntu 14.04.2 LTS, 15.10, 16.04, 17.04 and 18.04 A nice and cool install script made by @daveio is found here: https://github.com/daveio/attacksurface/blob/master/proxmark3/pm3-setup.sh Open a terminal: Download (and install) p7zip, and components essential to build the Proxmark from 
source: sudo apt install p7zip git build-essential libreadline5 libreadline-dev libusb-0.1-4 libusb-dev libqt4-dev perl pkg-config wget libncurses5-dev gcc-arm-none-eabi libstdc++-arm-none-eabi-newlib libpcsclite-dev pcscd --- Note: if you get an error make sure you're linux is up to date - sudo apt update + sudo apt upgrade --- Check out the latest revision of the Proxmark project: git clone https://github.com/proxmark/proxmark3.git Enter the repository: cd proxmark3 Get the latest commits : git pull Install the blacklist rules: sudo cp -rf driver/77-mm-usb-device-blacklist.rules /etc/udev/rules.d/77-mm-usb-device-blacklist.rules sudo udevadm control --reload-rules Add user to dialout group. If you do this one, you need to logout and login in again to make sure your rights got changed. sudo adduser $USER dialout Compiling the proxmark3 source code Clean and complete compilation: make clean && make all Plug in the Proxmark3 Insert the Proxmark and check “dmesg”, you will get one of the following outputs that will affect the next few steps. dmesg | grep -i usb HID device Remember this is very rare today, to find a device with HID firmware installed. [ 5414.961137] usb 2-2.2: new full speed USB device number 11 using uhci_hcd
 May 3 15:53:43 proxtest mtp-probe: checking bus 2, device 11: "/sys/devices/pci0000:00/0000:00:11.0/0000:02:00.0/usb2/2-2/2-2.2" [ 5422.297626] generic-usb 0003:9AC4:4B8F.0008: hiddev0,hidraw2: USB HID v1.00 Device [ProxMark-3 RFID Instrument] on usb-0000:02:00.0-2.2/input0 Jump to ==Flashing HID==. CDC device [10416.461687] usb 2-1.2: new full-speed USB device number 12 using ehci_hcd [10416.555093] usb 2-1.2: New USB device found, idVendor=9ac4, idProduct=4b8f [10416.555105] usb 2-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [10416.555108] usb 2-1.2: Product: PM3 [10416.555111] usb 2-1.2: Manufacturer: proxmark.org [10416.555871] cdc_acm 2-1.2:1.0: ttyACM0: USB ACM device Here look at the last row above and remember which tty your device got connected to. In this sample we got ttyACM0 Jump to ==Flashing CDC==. Flashing HID Use the older version of the flasher to update the proxmark: cd client/hid-flasher make ./flasher -b ../../bootrom/obj/bootrom.elf ./flasher ../../armsrc/obj/fullimage.elf
 cd ../.. Once you have updated here, your proxmark should be using CDC. So futher flashing should follow that section of instructions. It is very rare today that your device has HID version installed. You must have version r765 or earlier. This is the old verisoning system based on the old SVN repo. Totally outdated since you are reading this on GitHub. (2017-08-07) the latest release is v3.0.1, its just for reference. Jump to ==Running the proxmark3 client==. Flashing CDC Flash the BOOTROM, FULLIMAGE: client/flasher /dev/ttyACM0 -b bootrom/obj/bootrom.elf armsrc/obj/fullimage.elf Running the proxmark3 client Change into the client folder: cd client Run the client: ./proxmark3 /dev/ttyACM0 If all went well you should get some information about the firmware and memory usage as well as the following prompt: proxmark3> Now run the following commands to verfiy functionality proxmark3>hw status proxmark3>hw version proxmark3>hw tune You are now ready to use your newly upgraded Pro�