STM32F10x_FW_V3.3.0.zip

/** @page binary_template AN2557 Binary Template Readme file @verbatim ******************** (C) COPYRIGHT 2010 STMicroelectronics ******************* * @file IAP/binary_template/readme.txt * @author MCD Application Team * @version V3.3.0 * @date 10/15/2010 * @brief Description of the binary_template directory. ****************************************************************************** * THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS * WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE * TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY * DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING * FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE * CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS. ****************************************************************************** @endverbatim @par Description This directory contains a set of sources files that build the application to be loaded into Flash memory using In-Application Programming (IAP, through USART). To build such application, some special configuration has to be peformed: 1. Set the program load address at 0x08003000, using your toolchain linker file. 2. Relocate the vector table at address 0x08003000, using the "NVIC_SetVectorTable" function. The SysTick example provided within the STM32F10x Standard Peripherals library examples is used as illustration. This example configures the SysTick to generate a time base equal to 1 ms. The system clock is set to the maximum system frequency, the SysTick is clocked by the AHB clock (HCLK). A "Delay" function is implemented based on the SysTick end-of-count event. Four LEDs are toggled with a timing defined by the Delay function. @par Directory contents - "IAP\binary_template\EWARM": This folder contains a pre-configured project file that produces a binary image of SysTick example to be loaded with IAP. - "IAP\binary_template\RIDE": This folder contains a pre-configured project file that produces a binary image of SysTick example to be loaded with IAP. - "IAP\binary_template\MDK-ARM": This folder contains a pre-configured project file that produces a binary image of SysTick example to be loaded with IAP. - "IAP\binary_template\HiTOP": This folder contains a pre-configured project file that produces a binary image of SysTick example to be loaded with IAP. - "IAP\binary_template\TrueSTUDIO": This folder contains a pre-configured project file that produces a binary image of SysTick example to be loaded with IAP. - "IAP\binary_template\inc": contains the binary_template firmware header files - IAP/binary_template/inc/stm32f10x_conf.h Library Configuration file - IAP/binary_template/inc/stm32f10x_it.h Header for stm32f10x_it.c - IAP/binary_template/inc/main.h Header for main.c - "IAP\binary_template\src": contains the binary_template firmware source files - IAP/binary_template/src/main.c Main program - IAP/binary_template/src/stm32f10x_it.c Interrupt handlers - IAP/binary_template/src/system_stm32f10x.c STM32F10x system source file @par Hardware and Software environment - This example runs on STM32F10x Connectivity line, High-Density, High-Density Value line, Medium-Density, XL-Density, Medium-Density Value line, Low-Density and Low-Density Value line Devices. - This example has been tested with STMicroelectronics STM32100E-EVAL (High-Density Value line), STM32100B-EVAL (Medium-Density Value line), STM3210C-EVAL (Connectivity line), STM3210E-EVAL (High-Density and XL-Density), STM3210B-EVAL (Medium-Density) and STM3210E-EVAL (High-Density Value line) evaluation boards and can be easily tailored to any other supported device and development board. To select the STMicroelectronics evaluation board used to run the example, uncomment the corresponding line in stm32_eval.h file (under Utilities\STM32_EVAL) - STM32100E-EVAL Set-up - Use LED1, LED2, LED3 and LED4 connected respectively to PF.06, PF0.7, PF.08 and PF.09 pins - STM32100B-EVAL Set-up - Use LED1, LED2, LED3 and LED4 connected respectively to PC.06, PC.07, PC.08 and PC.09 pins - STM3210C-EVAL Set-up - Use LED1, LED2, LED3 and LED4 connected respectively to PD.07, PD.13, PF.03 and PD.04 pins - STM3210E-EVAL Set-up - Use LED1, LED2, LED3 and LED4 connected respectively to PF.06, PF0.7, PF.08 and PF.09 pins - STM3210B-EVAL Set-up - Use LED1, LED2, LED3 and LED4 connected respectively to PC.06, PC.07, PC.08 and PC.09 pins @par How to use it ? In order to load the SysTick example with the IAP, you must do the following: - EWARM (v5.50 and later): - Open the SysTick.eww workspace - In the workspace toolbar select the project config: - STM32100E-EVAL: to configure the project for STM32 High-density Value line devices - STM3210E-EVAL_XL: to configure the project for STM32 XL-density devices - STM32100B-EVAL: to configure the project for STM32 Medium-Density Value line devices - STM3210C-EVAL: to configure the project for STM32 Connectivity line devices - STM3210B-EVAL: to configure the project for STM32 Medium-density devices - STM3210E-EVAL: to configure the project for STM32 High-density devices - Rebuild all files: Project->Rebuild all - A binary file "SysTick.bin" will be generated under "STM3210E-EVAL_XL\Exe", "STM32100B-EVAL\Exe", "STM3210C-EVAL\Exe", "STM3210E-EVAL\Exe", "STM3210B-EVAL\Exe" or "STM32100E-EVAL\Exe" folder depending on the selected configuration. - Finally load this image with IAP application - RIDE: - Open the SysTick.rprj project - In the configuration toolbar(Project->properties) select the project config: - STM32100E-EVAL: to configure the project for STM32 High-density Value line devices - STM3210E-EVAL_XL: to configure the project for STM32 XL-density devices - STM32100B-EVAL: to configure the project for STM32 Medium-Density Value line devices - STM3210C-EVAL: to configure the project for STM32 Connectivity line devices - STM3210B-EVAL: to configure the project for STM32 Medium-density devices - STM3210E-EVAL: to configure the project for STM32 High-density devices - Rebuild all files: Project->build project - Go to "Utilities\Binary" directory and run "hextobin.bat" - A binary file "SysTick.bin" will be generated under "\STM3210E-EVAL_XL", "\STM32100B-EVAL", "\STM32100B-EVAL", "\STM3210C-EVAL", \STM3210E-EVAL", "\STM3210B-EVAL" or "\STM32100E-EVAL" folder depending on the selected configuration. - Finally load this image with IAP application - MDK-ARM: - Open the SysTick.uvproj project - In the build toolbar select the project config: - STM32100E-EVAL: to configure the project for STM32 High-density Value line devices - STM3210E-EVAL_XL: to configure the project for STM32 XL-density devices - STM32100B-EVAL: to configure the project for STM32 Medium-Density Value line devices - STM3210C-EVAL: to configure the project for STM32 Connectivity line devices - STM3210B-EVAL: to configure the project for STM32 Medium-density devices - STM3210E