HSM+USB+Serial+Driver+version+3.5.11_findusbpkgver_HSMUSB_findus

Honeywell USB Serial Driver Installation WINDOWS OS SUPPORTED: ====================== 1/ Windows XP 32 and 64 bit 2/ Windows Vista 32 and 64 bit 3/ Windows 7 32 and 64 bit 4/ Windows 8 32 and 64 bit 5/ Windows 8.1 32 and 64 bit 6/ Windows 10 32 and 64 bit 7/ Windows Embedded WEPOS 1.x 8/ Windows Embedded POSReady 2009 9/ Windows Embedded POSReady 7 10/ Windows Embedded 8 Industry 11/ Windows Embedded 8.1 Industry 12/ Windows 10 IoT Enterprise LTSB 2015 Uncompress the driver install media and save to target computer as <driver install directory>. The <driver install directory> is the directory folder where all the files in the driver install media get uncompressed and copied to. The name of the <driver install directory> can be any valid string name of the user choice. BEFORE PROCEED, PLEASE CONSULT THE "NOTES" SECTION AT THE BOTTOM OF THIS DOCUMENT FOR SPECIAL USE CASES. NORMAL(INTERACTIVE) INSTALL/UNINSTALL (for normal user) ======================================================= 1) INSTALLATION: The driver can be installed to target computer by following one of the below methods: a/ Method 1 -- Install from a command prompt i/ Open a Command Prompt with "elevated priviledge". Right click "Start->All Programs->Accessories->Command Prompt". Select "Run as administrator". ii/ cd <driver install directory> iii/ Run setup.bat iv/ Follow installation instructions. v/ Because this driver release package is NOT WHQL certified, pops up will occurs, but different pop up behavior will be observed depending on the version of Windows OS. Please follow the below steps: a/ Windows 7, 8, 8.1, and 10 (both 32 and 64 bit): * During driver install, "Windows Security" pop up will occur. Select the checkbox "Always trust software from Honeywell International Inc.", then click "Install". * When connecting new hw device, Windows should automatically find the correct driver to install. Sometimes, Windows can't find the correct driver to install, the user must manually "update" the driver. This manual process needs to be done two times, once for each new device model the first time it connects. Once for USB device enumeration under "USB" device class, and once for CDC-ACM device enumeration under "Ports (COM & LPT)" device class. Browse the correct device under Windows Device Manager, right click, and select "Update Driver Software". Select "Browse my computer for driver software", and browse to the correct "driver installed location", and select next. The "driver installed location" is the folder location supplied during the driver install wizard. b/ Windows XP (both 32 and 64 bit) * During driver install, "Software Installation" pops up will occur. Select "Continue Anyway" for each of the pop up. * When connecting new hw device, "Found New Hardware Wizard" pop up will occur twice. Once for USB device enumeration under "USB" device class, and once for CDC-ACM device enumeration under "Ports (COM & LPT)" device class. For each pop up, do as follow: - Select the "No, not this time" option, click Next. - Select "Install from a list or specific location (Advanced)" option, click Next. - Select the default option, "Search for the best driver in these locations", check the "Include this location in the search" checkbox, and browse to the correct "driver installed location", select next. The "driver installed location" is the folder location supplied during the driver install wizard. b/ Method 2 -- Install from Windows Explorer (Note: This method recommended if the <driver install directory> is stored localy on target machine. Do not use this method if the <driver install directory> is stored in a network location) i/ Open the <driver install directory> with Windows Explorer. ii/ Right click the file "setup.bat" and select "Run as administrator" iii/ Follow installation instructions. iv/ Because this driver release package is NOT WHQL certified, pops up will occurs, but different pop up behavior will be observed depending on the version of Windows OS. Please follow the below steps: a/ Windows 7, 8, 8.1, and 10 (both 32 and 64 bit): * During driver install, "Windows Security" pop up will occur. Select the checkbox "Always trust software from Honeywell International Inc.", then click "Install". * When connecting new hw device, Windows should automatically find the correct driver to install. Sometimes, Windows can't find the correct driver to install, the user must manually "update" the driver. This manual process needs to be done two times, once for each new device model the first time it connects. Once for USB device enumeration under "USB" device class, and once for CDC-ACM device enumeration under "Ports (COM & LPT)" device class. Browse the correct device under Windows Device Manager, right click, and select "Update Driver Software". Select "Browse my computer for driver software", and browse to the correct "driver installed location", and select next. The "driver installed location" is the folder location supplied during the driver install wizard. b/ Windows XP (both 32 and 64 bit) * During driver install, "Software Installation" pops up will occur. Select "Continue Anyway" for each of the pop up. * When connecting new hw device, "Found New Hardware Wizard" pop up will occur twice. Once for USB device enumeration under "USB" device class, and once for CDC-ACM device enumeration under "Ports (COM & LPT)" device class. For each pop up, do as follow: - Select the "No, not this time" option, click Next. - Select "Install from a list or specific location (Advanced)" option, click Next. - Select the default option, "Search for the best driver in these locations", check the "Include this location in the search" checkbox, and browse to the correct "driver installed location", select next. The "driver installed location" is the folder location supplied during the driver install wizard. 2) UNINSTALLATION: The installed driver can be uninstalled from target computer by following one of the below methods: a/ Method 1 - Uninstall from <Control Panel>\<Uninstall a program> i/ Start->Control Panel->Uninstall a program ii/ Select "Honeywell USB Serial Driver xxx". Click "Uninstall" iii/ Follow uninstallation instructions. b/ Method 2 -- Uninstall from a command prompt i/ Open a Command Prompt with "elevated priviledge". Right click "Start->All Programs->Accessories->Command Prompt". Select "Run as administrator". ii/ cd <driver install directory> iii/ Run setup.bat iv/ Follow uninstallation instructions. c/ Method 3 -- Uninstall from Windows Explorer (Note: This method recommended if the <driver install directory> is stored localy on target machine. Do not use this method if the <driver install directory> is stored in a network location) i/ Open the <driver install directory> with Windows Explorer. ii/ Right click the file "setup.bat" and select "Run as administrator" iii/ Follow uninstallation instructions. SILENT(NON INTERACTIVE) INSTALL/UNINSTALL (for IT/System Administrator) ======================================================================= This driver package can also be silently installed/uninstalled if required. This approach should NOT be used by a normal user but rather by an IT/Administrator personel. a/ Silently install the driver package on target machi