Single Phase, Multifunction Metering IC
with Neutral Current Measurement
ADE7953
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 www.analog.com
Fax: 781.461.3113 ©2011 Analog Devices, Inc. All rights reserved.
FEATURES
Measures active, reactive, and apparent energy; sampled
waveform; current and voltage rms
Provides a second current input for neutral current
measurement
Less than 0.1% error in active and reactive energy
measurements over a dynamic range of 3000:1
Less than 0.2% error in instantaneous IRMS measurement
over a dynamic range of 1000:1
Provides apparent energy measurement and instantaneous
power readings
1.23 kHz bandwidth operation
Flexible PGA gain stage (up to ×22)
Includes internal integrators for use with Rogowski coil sensors
SPI, I
2
C, or UART communication
GENERAL DESCRIPTION
The ADE7953 is a high accuracy electrical energy measurement
IC intended for single phase applications. It measures line voltage
and current and calculates active, reactive, and apparent energy,
as well as instantaneous rms voltage and current.
The device incorporates three Σ-Δ ADCs with a high accuracy
energy measurement core. The second input channel simulta-
neously measures neutral current and enables tamper detection
and neutral current billing. The additional channel incorporates
a complete signal path that allows a full range of measurements.
Each input channel supports independent and flexible gain stages,
making the device suitable for use with a variety of current sensors
such as current transformers (CTs) and low value shunt resistors.
Two on-chip integrators facilitate the use of Rogowski coil sensors.
The ADE7953 provides access to on-chip meter registers via a
variety of communication interfaces including SPI, I
2
C, and
UART. Two configurable low jitter pulse output pins provide
outputs that are proportional to active, reactive, or apparent
energy, as well as current and voltage rms. A full range of power
quality information such as overcurrent, overvoltage, peak, and
sag detection are accessible via the external
IRQ
pin. Independent
active, reactive, and apparent no-load detections are included to
prevent “meter creep.” Dedicated reverse power (
REVP
), zero-
crossing voltage (ZX), and zero-crossing current (ZX_I) pins
are also provided. The ADE7953 energy metering IC operates
from a 3.3 V supply voltage and is available in a 28-lead LFCSP
package.
FUNCTIONAL BLOCK DIAGRAM
PGA
IAP
IAN
VP
VN
IBP
IBN
SINC
AND
DECIMATION
FILTER
1.2V REF
LOW NOISE
PRE-AMP
PGA
CONFIGURATION
AND CONTROL
PGA
UART I
2
CSPI INTERFACE
DSP
REVP
ZX
ZX_I
PEAK
ANGLE
POWER FACTOR
SAG
WAVEFORM
SAMPLING
ADE7953
ENERGY
METERING
PROCESSOR
DIGITAL
FREQUENCY
CONVERSION
AWATT
BWATT
AVAR
BVAR
AVA
BVA
CF1DEN
CF2DEN
AENERGYA
RENERGYA
APENERGYA
AENERGYB
RENERGYB
APENERGYB
AGND
DGND
IRQ CS MISO/
SDA/
Tx
MOSI/
SCL/
Rx
SCLK
CLKIN
REF RESET VDD VINTA VINTD
CLKOUT
CF2
CF1
REVP
ZX
ZX_I
09320-001
ADC
ADC
ADC
Figure 1.
评论0