没有合适的资源?快使用搜索试试~ 我知道了~
西门子SINAMICS G120控制单元CU240E说明书.pdf
5星 · 超过95%的资源 需积分: 47 20 下载量 98 浏览量
2019-09-13
00:26:23
上传
评论 1
收藏 2.44MB PDF 举报
温馨提示
试读
422页
西门子SINAMICS G120控制单元CU240E说明书pdf,西门子SINAMICS G120控制单元CU240E说明书
资源推荐
资源详情
资源评论
s
sinamics
G120
G120
Control Units
CU240E
CU240S
Parameter Manual · Edition 11/2008
Edition 11/2008
SINAMICS
SINAMICS G120
Control Units CU240E
CU240S
Parameter Manual
This Parameter Manual is valid for the following Control
Units and Firmware versions:
Control Unit As from Firmware version:
CU240E V3.2
CU240S V3.2
CU240S DP V3.2
CU240S DP-F V3.2
CU240S PN V3.2
CU240S PN-F V3.2
A5E00807461B AF
s
Parameters
1
Function diagrams
2
Faults and Warnings
3
ASCII-Table
A
List of Abbreviations
B
Index
C
Copyright Siemens AG 2008 All Rights Reserved
The distribution and duplication of this document or the utilization and
transmission of its contents are not permitted without express written
permission. Offenders will be liable for damages. All rights, including
rights created by patent grant or registration of a utility model or
design, are reserved.
Siemens AG
Automation & Drives
Standard Drives
Postfach 3269, 91050 Erlangen
Germany
Disclaimer of Liability
We have reviewed the contents of this publication to ensure
consistency with the hardware and software described. Since
variance cannot be precluded entirely, we cannot guarantee full
consistency. However, the information in this publication is reviewed
regularly and any necessary corrections are included in subsequent
editions.
© Siemens AG 2008
Technical data subject to change.
Safety Guidelines
This manual contains notices you have to observe in order to ensure your personal safety, as well as to
prevent damage to property. The notices referring to your personal safety are highlighted in the manual
by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These
notices shown below are graded according to the degree of danger.
If more than one degree of danger is present, the warning notice representing the highest degree of dan-
ger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning
relating to property damage.
Qualified Personnel
The device/system may only be set up and used in conjunction with this documentation. Commissioning
and operation of a device/system may only be performed by qualified personnel. Within the context of
the safety notes in this documentation qualified persons are defined as persons who are authorized to
commission, ground and label devices, systems and circuits in accordance with established safety prac-
tices and standards.
Prescribed Usage
Note the following:
Trademarks
All names identified by ® are registered trademarks of the Siemens AG. The remaining trademarks in this
publication may be trademarks whose use by third parties for their own purposes could violate the rights
of the owner.
Danger
indicates that death or severe personal injury will result if proper precautions are not taken.
Warning
indicates that death or severe personal injury may result if proper precautions are not taken.
Caution
with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not
taken.
Caution
without a safety alert symbol, indicates that property damage can result if proper precautions are not
taken.
Notice
indicates that an unintended result or situation can occur if the corresponding information is not taken into
account.
Warning
This device may only be used for the applications described in the catalog or the technical description and
only in connection with devices or components from other manufacturers which have been approved or
recommended by Siemens.
Correct, reliable operation of the product requires proper transport, storage, positioning and assembly as
well as careful operation and maintenance.
Siemens Aktiengesellschaft SINAMICS G120 Control Units CU240E/S
Contents-5© Siemens AG 2008 All Rights Reserved
SINAMICS G120 Control Units CU240E/S, Edition 11/2008
Contents
1 Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
1.1 Introduction to Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
1.2 List of Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-13
1.3 Command and Drive Data Sets – Overview . . . . . . . . . . . . . . . . . . . . . 1-295
1.3.1 Command Data Sets (CDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-295
1.3.2 Drive Data Sets (DDS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-297
1.4 Connector/Binector (BICO)-Parameters . . . . . . . . . . . . . . . . . . . . . . . . 1-302
1.4.1 Binector Input Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-302
1.4.2 Connector Input Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-304
1.4.3 Binector Output Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-305
1.4.4 Connector Output Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-306
1.4.5 Connector/Binector Output Parameters . . . . . . . . . . . . . . . . . . . . . . . . 1-309
1.5 Quick commissioning (P0010 = 1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-310
2 Function diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-313
2.1 Contents: function diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-314
2.2 Symbols in function diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-316
2.3 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-318
2.4 External Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-321
2.5 Internal Setpoint Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-336
2.6 Technology Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-343
2.7 Free Function Blocks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-355
2.8 Setpoint Channel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-360
2.9 V/f Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-366
2.10 Vector Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-369
3 Faults and Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-383
3.1 Faults and Warnings – Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-384
3.2 List of Fault and Warning Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-385
AASCII-Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-411
B List of Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-413
CIndex . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C-417
剩余421页未读,继续阅读
资源评论
- 泡泡SOHO2023-07-25总体而言,这份说明书简洁实用,是学习和了解SINAMICS G120控制单元CU240E的好助手。
- 宏馨2023-07-25文件结构清晰,使用了适当的标题和标签,方便用户快速查阅相关内容。
- 禁忌的爱2023-07-25说明书中提供了一些实际案例和示意图,可以帮助用户更好地理解产品的使用场景。
- 战神哥2023-07-25这份SINAMICS G120控制单元CU240E说明书详细介绍了产品的功能和使用方法,对于初次接触的用户来说,十分实用。
- 点墨楼2023-07-25文件中的语言简洁明了,没有使用过多的专业词汇,非常适合不熟悉控制单元的用户。
weixin_38743968
- 粉丝: 404
- 资源: 2万+
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功