没有合适的资源?快使用搜索试试~ 我知道了~
汽轮机运行培训教材.pptx
1.该资源内容由用户上传,如若侵权请联系客服进行举报
2.虚拟产品一经售出概不退款(资源遇到问题,请及时私信上传者)
2.虚拟产品一经售出概不退款(资源遇到问题,请及时私信上传者)
版权申诉
0 下载量 133 浏览量
2021-10-04
23:01:47
上传
评论
收藏 438KB PPTX 举报
温馨提示
试读
33页
汽轮机运行培训教材.pptx
资源推荐
资源详情
资源评论
苏丹喀北电站汽机资料
汽轮机运行 turbine operation
1. 机组的启动 1. STARTUP OF TURBINE
1.1 汽轮机组在下列情况时禁止启动
a )危急保安器动作不正常,高压自动主汽门、调节汽门、抽汽逆止门卡涩或不能关严时;
b )汽轮发电机组转动部分有明显的摩擦声;机内有明显的金属声。
c )调速系统不能维持汽轮机空负荷运行,或机组甩负荷后不能维持转速在危急保安器动作转速
以下;
d )主轴晃动值相对于原始值大于 0.02mm (转子温度均匀状态允许的原始晃动值不大于
0.05mm )
e )辅助油泵,顶轴系统及盘车装置失常时;
1.1 Forbidden startup scope of turbine
a) When emergency governor acts abnormally, HP automatic main stop valve, governing
valve or bleed steam check valve has blockage or can not be closed fully;
b) There is obvious friction sound in rotary part of turbo-generator unit; there is obvious
metal collision sound.
c) Speed governing system can not maintain no-load operation of turbine, or after unit
rejects load, it can not maintain rotary speed below the action speed of emergency
governor:
d) vibration value of main shaft is 0.02mm bigger than original value (the original
vibration value in even state of rotor temperature is no big than 0.05mm);
e) When auxiliary oil pump, jacking oil system and turning gear device are abnormal;
苏丹喀北电站汽机资料
f )抗燃油或透平油油质不合格,油温低于正常(油系统充满油后);
g )保温不完整;
h )主要仪表(如轴向位移,相对膨胀,转速表及重要金属温度表,主
蒸汽压力和温度表等)失灵时;
i )汽缸调节级区域上下缸温度超过 50℃ ;
k) 汽轮机真空不能保持 0.067MPa 时。
f) EH oil or turbine oil is not qualified, and oil temperature is abnormal
(after oil system is full of oil);
g) Insulation is not complete;
h) Main instruments (such as axial displacement, relative expansion,
tachometer and important metal thermometer, main steam pressure
condenser vacuum meter and thermometer) has failure;
i) The upper and the lower casings temperature of turbine governing
stage area exceeds 50 .℃
j) Vacuum of turbine can not keep at 0.067MPa.
苏丹喀北电站汽机资料
1.2 启动前的准备工作 1.2 Preparation before turbine startup:
a )检查油系统,油箱、油管道、冷油器不漏油,油箱油位正常,
油箱和冷油器放油门关严,冷油器进、出口油门处于开启位置,
交流、直流电动润滑油泵入口门开启,出口门开启;
b )电动主闸门及其旁路门处于关闭位置;
c )自动主汽门、调速汽门处于关闭位置;
d )管道和汽缸本体疏水阀处于开启位置;
e )各抽汽管道逆止门处于关闭位置;
a) Check whether oil system, oil tank, oil pipes and oil cooler leak, oil level is
normal, outlet valve of oil tank and oil cooler closes tightly, inlet and outlet oil
valve of oil cooler is in open position, inlet valve and outlet valve of AC and DC
electric lube oil pump are open.
b) Electric main stop valve and other bypass valves are in closed position;
c) Auto main stop valve and speed governing valve are in closed position;
d) Drain valves of pipe and casing proper are in open position;
e) Each bleed steam pipe check valve is in closed position;
苏丹喀北电站汽机资料
f )轴承进油温度不低于 35℃ ;
g )抗燃油源各阀门状态正确,油温升至 20℃ 以上,抗燃油系统压力
调至 14MPa 。
f) Inlet oil temperature of bearing is no less than 35℃ ;
g) Valves of fire-proof oil source are in right state, oil temperature rises
above 20 , and the fire-proof oil system pressure is adjusted to ℃
14MPa.
苏丹喀北电站汽机资料
1.3 锅炉点火前的操作
a )投入发电机冷却系统;
b )启动排烟装置;
c )启动交流润滑油泵,使润滑油系统开始循环;
d )油循环进行 10min 后,启动高压油泵;
e )按顶轴装置说明书投入顶轴装置。检查各轴承顶轴油压正常,然后投盘车
装置,测量大轴晃动度,倾听机组内部声音;
f )油系统的结构和参数检查必须严格,否则要造成严重事故;
1.3 Preparation before boiler ignition:
a) Put generator cooling system into operation;
b) Startup smoke venting device;
c) Start up AC lube oil pump to make lube oil system began to circulate;
d) After oil circulation is maintained for 10 minutes, start up HP oil pump;
e) Start up jacking oil pump. Check whether jacking oil pressure of each
bearing is normal, and then put turning gear into operation, measure shaking
degree of main shaft and listen to inner part of unit;
f) Strictly check structure and parameters of oil system, or it may cause serious
accident;
剩余32页未读,继续阅读
资源评论
收藏哲173
- 粉丝: 8
- 资源: 30万+
下载权益
C知道特权
VIP文章
课程特权
开通VIP
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功