没有合适的资源?快使用搜索试试~ 我知道了~
【船级社】 DNV Additive manufacturing - qualification and certificat
1.该资源内容由用户上传,如若侵权请联系客服进行举报
2.虚拟产品一经售出概不退款(资源遇到问题,请及时私信上传者)
2.虚拟产品一经售出概不退款(资源遇到问题,请及时私信上传者)
版权申诉
0 下载量 125 浏览量
2023-12-01
14:21:42
上传
评论
收藏 1MB PDF 举报
温馨提示
试读
48页
【船级社】 DNV Additive manufacturing - qualification and certification process for materials and components.pdf
资源推荐
资源详情
资源评论
The content of this service document is the subject of intellectual property rights reserved by DNV GL AS ("DNV GL"). The user
accepts that it is prohibited by anyone else but DNV GL and/or its licensees to offer and/or perform classification, certification
and/or verification services, including the issuance of certificates and/or declarations of conformity, wholly or partly, on the
basis of and/or pursuant to this document whether free of charge or chargeable, without DNV GL's prior written consent.
DNV GL is not responsible for the consequences arising from any use of this document by others.
The electronic pdf version of this document, available free of charge
from http://www.dnvgl.com, is the officially binding version.
DNV GL AS
CLASS GUIDELINE
DNVGL-CG-0197 Edition November 2017
Additive manufacturing - qualification and
certification process for materials and
components
FOREWORD
DNV GL class guidelines contain methods, technical requirements, principles and acceptance
criteria related to classed objects as referred to from the rules.
©
DNV GL AS November 2017
Any comments may be sent by e-mail to rules@dnvgl.com
If any person suffers loss or damage which is proved to have been caused by any negligent act or omission of DNV GL, then DNV GL shall
pay compensation to such person for his proved direct loss or damage. However, the compensation shall not exceed an amount equal to ten
times the fee charged for the service in question, provided that the maximum compensation shall never exceed USD 2 million.
In this provision "DNV GL" shall mean DNV GL AS, its direct and indirect owners as well as all its affiliates, subsidiaries, directors, officers,
employees, agents and any other acting on behalf of DNV GL.
Changes - current
Class guideline — DNVGL-CG-0197. Edition November 2017 Page 3
Additive manufacturing - qualification and certification process for materials and components
DNV GL AS
CHANGES – CURRENT
This is a new document.
Contents
Class guideline — DNVGL-CG-0197. Edition November 2017 Page 4
Additive manufacturing - qualification and certification process for materials and components
DNV GL AS
CONTENTS
Changes – current.................................................................................................. 3
Section 1 General.................................................................................................... 5
1 Introduction.........................................................................................5
Section 2 Additive manufacturing........................................................................... 9
1 Introduction.........................................................................................9
2 Principles and overview of additive manufacturing processes........... 11
3 Additive manufacturing process description and variables................ 14
Section 3 Qualification and certification process.................................................. 25
1 Introduction.......................................................................................25
2 Certification scheme for materials and components.......................... 25
3 Qualification and certification framework for additive
manufacturing products........................................................................26
Appendix A Sequence of activities during an example MPQ process..................... 34
Appendix B Testing of additive manufacturing components..................................35
1 General overview of testing methodology for additive
manufacturing parts............................................................................. 35
Appendix C Principles of technology qualification process.................................... 40
1 Process for technology qualification.................................................. 40
Changes - historic.................................................................................................47
Section 1
Class guideline — DNVGL-CG-0197. Edition November 2017 Page 5
Additive manufacturing - qualification and certification process for materials and components
DNV GL AS
SECTION 1 GENERAL
1 Introduction
1.1 Objective
The purpose of this guideline is to support the introduction and use of additive manufacturing (AM)
technologies as an alternative method to produce materials, parts or components that are subject to approval
or verification in accordance with DNV GL rules and/or other applicable standards used by the Society.
Guidance note:
AM is a term used to cover a broad range of manufacturing processes (also known as 3D printing) that involve sequential-layer
material addition throughout a 3D work envelope under automated control.
---e-n-d---o-f---g-u-i-d-a-n-c-e---n-o-t-e---
1.2 Scope
This class guideline provides a framework for approval and certification of materials, products and
components made by additive manufacturing (AM) through a systematic qualification approach.
Interfaces between AM technologies and conventional technologies already covered by existing rules and
standards may be covered by this class guideline based on a case-by-case agreement with the Society.
1.3 Application
This document is applicable to stakeholders in the maritime industry, e.g. manufacturers and sub-suppliers of
materials, parts and components, service suppliers and end users adopting AM technologies. The guidelines
may be applied for:
— approval of pre-materials, materials, parts and components made by the use of additive manufacturing
process
— approval of AM related services
— specification of part-building requirements for end users.
It is applicable for materials, parts and components made by any AM processing route that may be defined
as one of the emerging AM technologies or concepts, but not covered by existing conventional manufacturing
or fabrication routes. Requirements for the qualification of manufacturers shall be considered in each case.
This consideration shall take into account the complexity and criticality of the product to be supplied,
manufacturer’s previous experience, and these guidelines.
1.4 Structure
This document is structured into three sections:
Section 1:
— introductory section where the objective, scope and other general details are presented.
Section 2:
— contains a brief introduction to AM technologies and discusses general principles of additive manufacturing
processes, important process parameters and variables. This section is mainly for reference purposes.
Section 3:
— provides guidance to the qualification process for additively manufactured materials and components, AM
qualification and certification work process and various services offered by DNV GL.
See App.C.
剩余47页未读,继续阅读
资源评论
phyit
- 粉丝: 7626
- 资源: 2614
下载权益
C知道特权
VIP文章
课程特权
开通VIP
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功