TeleLogic 4.2 安装文件

Sentinel System Drivers Version 5.3 README.TXT File Copyright (c) 1991-1996 Rainbow Technologies, Inc. All Rights Reserved. The Sentinel System Drivers provide a communication path between your protected application and the Sentinel key. The driver you use depends on the operating system you are using. This readme file describes the installation procedures for all Sentinel system drivers. See the appropriate section for the procedure about the driver that you are installing. ----------------------------------- README File Contents ----------------------------------- 1.0 File List 2.0 Changes Since Last General Release 3.0 Windows NT Driver Installation Procedure 3.1 Windows NT Driver Configuration 3.2 Windows NT Driver Un-install 3.3 Recovery Mechanisms on NT-4.0 3.4 Windows NT - DOS Device Driver 4.0 Windows 3.x Driver Installation Procedure 4.1 Windows 3.x Driver Configuration 4.2 Windows 3.x Driver Un-install 5.0 OS/2 Driver Installation Procedure 5.1 OS/2 Driver Configuration 6.0 Windows 95 Driver Installation Procedure 6.1 Windows 95 Driver Configuration 6.2 Windows 95 Driver Un-install ----------------------------------- 1.0 File List ----------------------------------- README.TXT - This file. SENTINEL.DDP - OS/2 installation script file. DOS\SENTDOS.SYS - DOS Device Driver for use with some interfaces under Windows NT. OS2\INSTALL.CMD - OS/2 installation command file. OS2\SENTINEL.SYS - OS/2 Sentinel Driver. WIN_31\INSTALL.EXE - Install program for Windows 3.x Sentinel Driver. WIN_31\SENTINEL.386 - Windows 3.x Sentinel Driver. WIN_NT\INSTALL.BAT - Batch file to invoke appropriate Win NT installation program under different hardware platform. WIN_NT\SETUPAXP.EXE - Sentinel Driver installation program for Windows NT on ALPHA platforms. WIN_NT\SETUPX86.EXE - Sentinel Driver installation program for Windows NT on INTEL platforms. WIN_NT\SETUPMPS.EXE - Sentinel Driver installation program for Windows NT on MIPS platforms. WIN_NT\SETUPPPC.EXE - Sentinel Driver installation program for Windows NT on Power PC platforms. WIN_NT\SNTI386.DLL - Sentinel Driver setup for Windows NT on Intel platforms. WIN_NT\SNTMIPS.DLL - Sentinel Driver setup for Windows NT on MIPS platforms. WIN_NT\SNTALPHA.DLL - Sentinel Driver setup for Windows NT on Alpha platforms. WIN_NT\SNTPPC.DLL - Sentinel Driver setup for Windows NT on Power PC platforms. WIN_NT\SENTINEL.ZIP - Windows NT Sentinel Driver User's Guide in Windows Write format (zipped). WIN_NT\I386\SENTTEMP.HLP - Help file for the WinNT Sentinel Driver setup DLL. WIN_NT\I386\SENTTEMP.SYS - WinNT Sentinel Driver for x86 systems. WIN_NT\I386\RNBOVTMP.DLL - WinNT Sentinel Virtual Device Driver for x86 systems. WIN_NT\MIPS\SENTTEMP.HLP - Help file for the WinNT Sentinel Driver setup DLL. WIN_NT\MIPS\SENTTEMP.SYS - WinNT Sentinel Driver for MIPS systems. WIN_NT\MIPS\RNBOVTMP.DLL - WinNT Sentinel Virtual Device Driver for MIPS systems. WIN_NT\ALPHA\SENTTEMP.HLP - Help file for the WinNT Sentinel Driver setup DLL. WIN_NT\ALPHA\SENTTEMP.SYS - WinNT Sentinel Driver for Alpha systems. WIN_NT\ALPHA\RNBOVTMP.DLL - WinNT Sentinel Virtual Device Driver for ALPHA systems. WIN_NT\PPC\SENTTEMP.HLP - Help file for the WinNT Sentinel Driver setup DLL. WIN_NT\PPC\SENTTEMP.SYS - WinNT Sentinel Driver for Power PC systems. WIN_NT\PPC\RNBOVTMP.DLL - WinNT Sentinel Virtual Device Driver for Power PC systems. WIN_95\SENTINEL.VXD - Windows 95 Sentinel Driver. WIN_95\SENTW95.EXE - Sentinel Driver installation program for Windows 95. WIN_95\SENTW95.DLL - Sentinel Driver installation DLL. WIN_95\SENTW95.HLP - Windows help file used by the DLL. WIN_95\SENTSTRT.EXE - Program used to initialize the VxD. ----------------------------------------------------- 2.0 Changes Since Last General Release (PD-5.17) ----------------------------------------------------- 1. Corrected a problem that caused the system to crash when the NetSentinel NT Service is set to "Automatic" startup on Windows NT 4.0. 2. The NT driver setup program now renames and marks the VDD and setup file as "MOVEFILE_DELAY_UNTIL_REBOOT". This is to prevent the driver to be deleted if "Install Driver" is call right after "Remove Driver" without rebooting machine. 3. Added new mechanisms to the Win95 driver un-installer to perform full clean-up. 4. Corrected a problem on NT and Win95 driver installer that failed the driver installation when the path is longer than 30 characters. 5. Added a "Autodetect Used?" check box to the NT and Win95 driver installer's Port Configuration dialog box to indicate if the port auto-detection is used. 6. Added version-checking mechanisms to the NT, Win95, and Win3.x driver installer to prevent older driver files from overwriting newer ones. Also added an overwrite (/o) switch to installer to allow the older versions to be installed. (by default, the installer will keep the new driver). 7. Modified the Win3 driver installer to prompt the user to restart Windows when the installation is done. 8. Added capabilities to the Win3 driver installer to handle read-only files. 9. Win3 driver installer now returns installation status. Please refer to the "Return Value of the Win 3.x driver installer" section below. 10. Optimized the speed of the driver to reduce the impact on certain time sensitive system tasks (such as mouse-pointer updates) when the Sentinel device is access continuously. 11. Added capability to Windows 95, Windows NT to coexist with other drivers that use ECP mode. 12. Added optional support for very low power parallel ports. 13. Added masking of system interrupts for protection of SuperPro, C-Plus write operations. 14. Corrected a problem where no error was reported when trying to access a SuperPro key that had been removed. 15. Corrected a problem with SENTDOS.SYS which caused problems with some types of applications. 16. Corrected a problem with SENTDOS.SYS where problems occurred using some international versions of Windows 95. ------------------------------------------------ 3.0 Windows NT Driver Installation Procedure ------------------------------------------------ 1. Make a backup copy of the diskette. 2. Under the Microsoft Windows NT Main group, double click on "Command Prompt". 3. Change drive to the floppy drive contains the Driver Diskette. In case of the floppy diskette distribution, change the current directory to \WIN_NT. In case of the CD-ROM distribution, change the current directory to \PRODUCT\DRIVERS\WIN_NT. 4. Type "INSTALL.BAT" at the command prompt. There are three command line options: (See the INSTALL.BAT file for examples.) 1. /q Quiet mode. Normal dialogs described below are not displayed. Error messages are displayed. 2. /pxxx Path, where xxx is the path of files to be installed. Specify the path of files to be installed. Otherwise, files will