Lenze GDC软件

GLOBAL DRIVE CONTROL - Version 4.9 Lenze 8200 and 9300 inverters can be parameterized and controlled with this software. Please observe the following information on the communication interface Optical Fibre: Optical fibre: For communication with the drive use the optical fibre and observe the following when there is more than one drive connected: "Search all baud rates" may not be activated for the dialog "Lecom-A/B - Find drives"! ------------------------------------------------ Caution: The user is provided with the software at issued. All risks regarding quality and the results obtained by application of the software, remain with the user. The user must take correspondng safety measures to protect the system against maloperation. We do not assume responsibility for directly or indirectly caused damage, e.g. profit losses, order losses or any other detriment. ------------------------------------------------ SYSTEM REQUIREMENTS: HARDWARE: IBM-AT or compatible PC CPU: Pentium 333 or higher min. 128 MByte RAM Hard disk with min. 250 MByte free memory capacity Super-VGA CD-ROM drive SOFTWARE: Windows 98 (Internet Explorer 5), Windows Me, Windows NT 4.0 (SP5, Internet Explorer 5), Windows 2000 (SP2) or Windows XP Online communication with inverter: RS232 / LWL / system bus (CAN) / RS485 (only with intelligent interface converter, i.e. automatic detection of the data flow direction) and OPC interface (only for OPC servers which comply with the DRIVECOM specification, version 1.0) ------------------------------------------------ DIRECTORY STRUCTURE: The individual components of GLOBAL DRIVE CONTROL are stored in different directories. The directory structure must not be changed. \GDC | +-- \BIN | +-- \PDB | +-- \DAT | +-- \DLL | +-- \HLP | +-- \OSZ | +-- \FBE Contents of the directories: \bin Executable program file gdc.exe, program library and configuration files \pdb Directory for the storage of the unit descriptions required by GLOBAL DRIVE CONTROL. The file extension of these files is always *.pdb. The unit descriptions are available in several languages. Therefore, the files are sorted according to the languages and saved in sub-directories. The identification code for the languages is identical to the language identification used in MS-DOS. \dat This directory saves the files with the parameter sets which are saved by the user. These files always have the extension *.gdc. \dll This directory contains drive-specific program libraries. \hlp Here you will find help files for the program GLOBAL DRIVE CONTROL as well as information about the inverters. \osz This directory contains the oscilloscope function \fbe This directory contains the function block editor ------------------------------------------------ SERIAL CONNECTION between PC and drive: The PC and the drive are connected via a cable with the following configuration: Lenze drive PC 9-pole SubD male plug 25-pole SubD female plug PIN PIN 2 o-------------------------------o 2 3 o-------------------------------o 3 5 o-------------------------------o 7 Lenze drive PC 9-pole SubD male plug 9-pole SubD female plug PIN PIN 2 o-------------------------------o 3 3 o-------------------------------o 2 5 o-------------------------------o 5 All connections which are not listed, are not assigned. For further information see Operating Instructions Field-bus module type 2102 for RS232, RS485, optical fibre. ------------------------------------------------ TECHNICAL PROBLEMS FAULT Parameter-set file cannot be read CAUSE-1 You tried to read in parameter-set files, which were generated by means of the DOS program 'Lemoc2' REMEDY-1 Global Drive Control uses a different format for filing the drive parameters. Transfer the parameter set from the controller to the PC and save it by means of Global Drive Control. CAUSE-2 You tried to read in parameter-set files, which were generated by means of the test version (V0.6 ) of Global Drive Control program. REMEDY-2 The type of the parameter-set file has changed from '*.VAR' to '*.GDC'. Please change the file type to '*.GDC' via the file manager. FAULT No controller communication. CAUSE-1 You use a wrong PC-system cable. REMEDY-1 Check system-cable wiring (see above) CAUSE-2 Controller is switched off or no voltage applied to LECOM-A/B-module 2102. REMEDY-2 Check voltage supply and controller connection. With external supply, check voltage applied to terminals 39 and 59 (see corresponding Operating Instructions) CAUSE-3 Wrong COM port selected REMEDY-3 Set the used COM port under the menu 'Options/communication' of the Global Drive Control program. CAUSE-4 Wrong setting of the interface parameter REMEDY-4 The interface parameters can be changed thanks to Windows system control: -COM1: address 03F8, IRQ 4 -COM2: address 02F8, IRQ 3 CAUSE-5 Faulty Windows configuration. The COM ports cannot be accessed via the Windows program 'Terminal' REMEDY-5 Reinstall Windows or eliminate the fault in the configuration under the file 'System.ini' ------------------------------------------------ GDC with system bus driver: NOTE Files and entries in the SYSTEM.INI will not be deleted when GDC is uninstalled. Please ensure not using the Drive Developer Studio (DDS) when deleting the files and entries, otherwise DDS cannot communicate with the drive! REMEDY-1 (Windows 9x) Delete the following files: \WINDOWS\SYSTEM\PEAKCANL.VXD \WINDOWS\SYSTEM\VCANW32.DLL oder \WIN95\SYSTEM\PEAKCANL.VXD \WIN95\SYSTEM\VCANW32.DLL Delete the following entries (SYSTEM.INI): device=peakcanl.vxd [PEAKCAN] Hardware1=2,0x378,7 Net1=GDC-PeakNet_1000, 1, 0x0014 Net2=GDC-PeakNet_125, 1, 0x031C Net3=GDC-PeakNet_250, 1, 0x011C Net4=GDC-PeakNet_50, 1, 0x472F Net5=GDC-PeakNet_500, 1, 0x001C REMEDY-2 (Windows NT 4.0) Delete the following files: \WINNT\SYSTEM32\DRIVERS\PEAKCAN.SYS \WINNT\SYSTEM32\VCANW32.DLL ------------------------------------------------ SERVICE: If you have technical problems with GLOBAL DRIVE CONTROL, please contact your Lenze representative or our hotline: Lenze Hotline 05154/82-1111