# For more options and information see
# http://rpf.io/configtxt
# Some settings may impact device functionality. See link above for details
# uncomment if you get no picture on HDMI for a default "safe" mode
#hdmi_safe=1
# uncomment the following to adjust overscan. Use positive numbers if console
# goes off screen, and negative if there is too much border
#overscan_left=16
#overscan_right=16
#overscan_top=16
#overscan_bottom=16
# uncomment to force a console size. By default it will be display's size minus
# overscan.
#framebuffer_width=1280
#framebuffer_height=720
# uncomment if hdmi display is not detected and composite is being output
#hdmi_force_hotplug=1
# uncomment to force a specific HDMI mode (this will force VGA)
#hdmi_group=1
#hdmi_mode=1
# uncomment to force a HDMI mode rather than DVI. This can make audio work in
# DMT (computer monitor) modes
#hdmi_drive=2
# uncomment to increase signal to HDMI, if you have interference, blanking, or
# no display
#config_hdmi_boost=4
# uncomment for composite PAL
#sdtv_mode=2
#uncomment to overclock the arm. 700 MHz is the default.
#arm_freq=800
# Uncomment some or all of these to enable the optional hardware interfaces
#dtparam=i2c_arm=on
#dtparam=i2s=on
#dtparam=spi=on
# Uncomment this to enable infrared communication.
#dtoverlay=gpio-ir,gpio_pin=17
#dtoverlay=gpio-ir-tx,gpio_pin=18
# Additional overlays and parameters are documented /boot/overlays/README
# Enable audio (loads snd_bcm2835)
dtparam=audio=on
# Automatically load overlays for detected cameras
camera_auto_detect=1
# Automatically load overlays for detected DSI displays
display_auto_detect=1
# Enable DRM VC4 V3D driver
dtoverlay=vc4-kms-v3d
max_framebuffers=2
# Disable compensation for displays with overscan
disable_overscan=1
[cm4]
# Enable host mode on the 2711 built-in XHCI USB controller.
# This line should be removed if the legacy DWC2 controller is required
# (e.g. for USB device mode) or if USB support is not required.
otg_mode=1
[all]
[pi4]
# Run as fast as firmware / board allows
arm_boost=1
[all]
没有合适的资源?快使用搜索试试~ 我知道了~
imageTailor用于定制图像的工具
共141个文件
conf:33个
sh:13个
xml:10个
1.该资源内容由用户上传,如若侵权请联系客服进行举报
2.虚拟产品一经售出概不退款(资源遇到问题,请及时私信上传者)
2.虚拟产品一经售出概不退款(资源遇到问题,请及时私信上传者)
版权申诉
0 下载量 55 浏览量
2023-11-27
13:59:58
上传
评论
收藏 739KB ZIP 举报
温馨提示
imageTailor用于定制图像的工具
资源推荐
资源详情
资源评论
收起资源包目录
imageTailor用于定制图像的工具 (141个子文件)
01-create-root 8KB
10-base-networking 844B
10-genfstab 1KB
20-setrootpwd 1KB
30-config-kernel 1KB
50-bootloader 4KB
50-bootloader 4KB
97-clean-yumlog 792B
98-clean-tmp-repo 2KB
98-clean-tmp-repo 2KB
98-clean-tmp-repo 2KB
99-install-rpm 904B
99-source_files 998B
99-source_files 816B
fw_payload_oe_uboot.bin 2.64MB
grub.cfg 618B
grub.cfg 618B
grub.cfg 604B
grub.cfg 491B
rpm.conf 152KB
rpm.conf 152KB
rpm.conf 97KB
rpm.conf 97KB
cmd.conf 81KB
cmd.conf 81KB
cmd.conf 74KB
cmd.conf 74KB
rpm.conf 24KB
security_s.conf 15KB
rpm.conf 14KB
security_s.conf 12KB
security_s.conf 10KB
security_s.conf 10KB
security.conf 9KB
cmd.conf 8KB
cmd.conf 8KB
security_s.conf 6KB
security_s.conf 6KB
product.conf 700B
sys.conf 680B
sys.conf 680B
product.conf 655B
sys.conf 384B
sys.conf 363B
RepositoryRule.conf 315B
RepositoryRule.conf 315B
product.conf 309B
minios.conf 106B
minios.conf 106B
sys.conf 0B
sys.conf 0B
sys.conf 0B
create-image 7KB
die 789B
filelist 234B
filelist 46B
config.xml.form 958B
config.xml.form 958B
icon-note.gif 394B
group 251B
grub 369B
ifcfg-eth0 303B
imageTailor_arch.jpg 48KB
splash.jpg 10KB
.kiwirc 0B
.kiwirc 0B
.kiwirc 0B
LICENSE 9KB
menu.lst 312B
menu.lst 312B
imageTailor 使用指南.md 47KB
design.zh.md 3KB
mkdliso 85KB
modules 354B
modules 354B
modules 344B
passwd 469B
password-auth-crond 2KB
password-auth-local 2KB
pi_pwd 0B
placeholder 0B
placeholder 0B
placeholder 0B
placeholder 0B
placeholder 0B
Env.pm 5KB
flowchart.png 21KB
csh.precmd 517B
LICENCE.raspberrypi-sys-mods 2KB
openeuler.repo 263B
repo 235B
repo 69B
repo 68B
root_pwd 106B
root_pwd 0B
rpmlist 509B
rpmlist 168B
rpmlist 148B
rpmlist 148B
99-com.rules 2KB
共 141 条
- 1
- 2
资源评论
Java程序员-张凯
- 粉丝: 1w+
- 资源: 6718
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功