本站原创 VB遥控播放器红外遥控解码_单片机C语言实例(纯C语言源代码).zip

#include <regX52.h> #define c(x) (x*110592/120000) sbit Ir_Pin=P3^2; sbit beep=P3^6; #define INBUF_LEN 4 //数据长度 unsigned char inbuf1[INBUF_LEN]={'0','0','0','0'};//发送缓冲区 unsigned char inbuf2[50];//接收缓冲区 unsigned char count3; void init_serialcomm( void ) { SCON = 0x50 ; //SCON: serail mode 1, 8-bit UART, enable ucvr T2CON=0x30; TH2=0x00; TL2=0x00; RCAP2H=0xFF; RCAP2L=0xDC; TR2=1; } //向串口发送一个字符 void send_char_com( unsigned char ch) { SBUF=ch; while (TI== 0 ); TI= 0 ; } //向串口发送一个字符串，strlen 为该字符串长度 void send_string_com( unsigned char *str, unsigned int strlen) { unsigned int k= 0 ; do { send_char_com(*(str + k)); k++; } while (k < strlen); } //串口接收中断函数 void serial () interrupt 4 using 3 { if (RI) //RI==开始接收 { unsigned char ch; RI = 0 ; //软件RI=0 ch=SBUF; if (ch> 1 ) { count3= 0 ; inbuf2[count3]=ch; } else { count3++; inbuf2[count3]=ch; } } } unsigned char code Led_Tab[]={0xC0,0xF9,0xA4,0xB0,0x99,0x92,0x82, 0xf8,0x80,0x90,0x88,0x83,0xC6,0xA1,0x86,0x8E}; //共阳极数码显示码0-F. unsigned char code Led_Sel[]={0xef,0xdf,0xbf,0x7f}; unsigned char dis_8[17]={'0','1','2','3','4','5','6','7','8','9','A','B','C','D','E','F','-'}; unsigned char Led_Buf[4]; //显示缓冲区 char Led_Index; //位选 unsigned char Ir_Buf[4]; //用于保存解码结果 void delay_50ms(unsigned int t) { unsigned int j; for(;t>0;t--) for(j=6245;j>0;j--) {;} } //============================================================== //数码管扫描 timer0() interrupt 1 using 1 { TL0=65536-1000; TH0=(65536-1000)/256; //定时器0设定约1000us中断一次，用于数码管扫描 //P0=0xff; P2=Led_Sel[Led_Index]; //位选 P0=Led_Tab[Led_Buf[Led_Index]]; //段选 if(++Led_Index>3) Led_Index=0; //四个扫描完了,到第一个数码管 } //============================================================== unsigned int Ir_Get_Low() { TL1=0; TH1=0; TR1=1; while(!Ir_Pin && (TH1&0x80)==0); TR1=0; return TH1*256+TL1; } //============================================================= unsigned int Ir_Get_High() { TL1=0; TH1=0; TR1=1; while(Ir_Pin && (TH1&0x80)==0); TR1=0; return TH1*256+TL1; } //============================================================== main() { unsigned int temp; char i,j; Led_Index=1; init_serialcomm(); //初始化串口 TMOD=0x11; TL0=65536-1000; TH0=(65536-1000)/256; //定时器0设定约1000us中断一次，用于数码管扫描 EA=1; ET0=1; TR0=1; Led_Buf[0]=0; Led_Buf[1]=0; Led_Buf[2]=0; Led_Buf[3]=0; //显示区设成0 do{ restart: while(Ir_Pin); temp=Ir_Get_Low(); if(temp<c(8500) || temp>c(9500)) continue;//引导脉冲低电平9000 temp=Ir_Get_High(); if(temp<c(4000) || temp>c(5000)) continue;//引导脉冲高电平4500 for(i=0;i<4;i++) //4个字节 for(j=0;j<8;j++) //每个字节8位 { temp=Ir_Get_Low(); if(temp<c(200) || temp>c(800)) goto restart; temp=Ir_Get_High(); if(temp<c(200) || temp>c(2000)) goto restart; Ir_Buf[i]>>=1; if(temp>c(1120)) Ir_Buf[i]|=0x80; } Led_Buf[0]=(Ir_Buf[2]/16)&0xf; Led_Buf[1]=Ir_Buf[2]&0xf; Led_Buf[2]=(Ir_Buf[3]/16)&0xf; //显示结果 Led_Buf[3]=Ir_Buf[3]&0xf; inbuf1[0]=dis_8[Led_Buf[0]]; inbuf1[1]=dis_8[Led_Buf[1]]; inbuf1[2]=0x0d; inbuf1[3]=0x0a; send_string_com(inbuf1,INBUF_LEN); beep=0; delay_50ms(2); beep=1; } while(1); }