Ti,Bq studio BQSTUDIO-STABLE BatteryManagementStudio-1.3.86

bqSBB Version 1.3.86 Release Notes ---------------------------------- Reverted chemistry changes for hex ID support Programming: Resolved possible issue with programming error DataFlash: Resolved issue of negative floats not accepted Commands: Resolved issue with seal/unseal bqSBB Version 1.3.85 Release Notes --------------------------------- Chemistry Programming: Change internal structures to store chemistry IDs in hexadecimal. ChemUpdater database version 638 and later support hexadecimal chemistry IDs. Display which chemsitry IDs support Turbo Mode on mixed chemistry screen. Advanced Comm SMB: Remove requirement that each byte of hexadecimal string in Write Block must be separated by a space. Calibration: Updated calibration algorithms to utilize double precision floating point calculations. Added support for bq27541V200 HH_Firmware calibration Registers: Added support for MAC commands on additional gauge platforms bq79606: Removed some ADC frequency options that are not currently supported by the hardware Disabled default reading of communication status table during launch Resolved a problem with broadcast read support on the scripting plugin Updated auto addressing algorithm to configure stack devices Several minor user interface updates bq25150: Register where one bit changes value of other registers Support for 16 Bits ADC read conversion bq25887: Added support for cell balancing in charger.xml for manual mode control in field view per spec Chargers: Default View support for 8 and 16 bits registers together bqSBB Version 1.3.84 Release Notes --------------------------------- bq79606: Added unmask support to the faults plugin bqSBB Version 1.3.83 Release Notes --------------------------------- bq79606: Resolved a problem with updating the log during script execution Dashboard: Update to scroll bar layout to support low resolution displays bqSBB Version 1.3.82 Release Notes --------------------------------- Chemistry: Allow programming of chemistry IDs that do not support Turbo Mode 2 into a gauge that supports Turbo Mode 2. A checkbox at the top of the chemistry screen displays additional chemistries when checked when bqStudio is connected to a TM2 gauge. General: Updates to the eclipse configuration to prevent workspace corruption Enhancements to SMBus address scanning during hardware enumeration DataGraph: Fixed minor problem with plotting points in the datagraph plugin Authentication: Added SHA1/ECC programming and authentication support for the bq40z80 bq79606: Resolved a problem with read transactions of 128 bytes Updated the translation log viewer in the advanced comm plugin to support large read payloads Updated the translation log viewer in the monitor scripting plugin to support large read payloads User interface updates to the communication control plugin Improved error messages in the FTDI log when the response queue and FTDI hardware is reset bqSBB Version 1.3.81 Release Notes --------------------------------- Calibration: Add support for bq40z80 Registers: Updates to SBS logging functionality to improve performance bq79606: Added a CRC calculator to the scripting plugin Added a stop button to the script execution plugin Updates to the communication control plugin user interface Enhancements to the FTDI backend response queue Adjustments to communication reset timing Updates to the baud rate detection algorithm bqSBB Version 1.3.80 Release Notes --------------------------------- Calibration: Added board and cc offset calibration for the bq9035 SHA Authentication: Change references in tool bar and menu from Authentication to SHA Authentication Programming: Change operations writing to address 0 to read/modify/write. Backend: Added additional debug log messages for pipe handling bqSBB Version 1.3.79 Release Notes --------------------------------- Data Ram and Data Memory: Add bq27z561 HDQ support Libraries: Add logging of some errors bq79606: Improved backend robustness when the stack topology changes Firmware: Resolved a problem that caused firmware updates to hang on some bq900x gauges bqSBB Version 1.3.78 Release Notes --------------------------------- Programming: Fix bq27750 srec programming exception sending execute firmware command after failure. Add 20 msec delay before executing ROM. Commands: Added Unseal and Full Access support for bq40z651 Charger: Added support for SN2600 charge parameters, watchdog reset, default view change to better support 16bit Field View registers. Added support for non-contiguous mask bits in signed charger ADC registers Charger SN2600 Charge Control: Change minimum IBAT_TARGET current from 16mA to 0. bqSBB Version 1.3.77 Release Notes --------------------------------- ECC Authentication: Change name to ECC Authentication Programming: Fix two functions to return error code used in SMB and I2C_SMB programming bq27z561: Authenctication: Added SHA-256 Authentication in Gauge/ROM Mode Removed SHA-1 Authentication GoldenImage: Added support for SREC, DFFS, BQFS, and GMFS export Programming: Added SREC and FS programming support Improved error report for FS file programming Calibration: Max voltage threshold increased to 6000 mV Current calibration scaled by factor of 4 Removed Batt and Pack calibration feature bq79606: Added support for AUX_CELL configuration and measurement Several enhancements to plugin user interfaces Chargers: Added support for signed values in the ADC tab bqSBB Version 1.3.76 Release Notes --------------------------------- Chemistry: Increase number of chemIDs from 2000 to 3000 bqSBB Version 1.3.75 Release Notes --------------------------------- bq79606: Tuned the comm break algorithm for all baud rates Updated the baud rate detection algorithm to support the latest silicon Chemistry: Updates to the MaxLife chemistry programming and cycle count Commands: Added support for SMB read word commands bqSBB Version 1.3.74 Release Notes --------------------------------- Chemsitry: Add 2 additional Ra tables to support bq9006. Allow option to program chemistry GPCRb file created on www.ti.com into multicell gauge when Turbo Mode 2 data is not available for chem ID. bqSBB Version 1.3.73 Release Notes --------------------------------- bq79606: Command sequence buttons can be assigned now after install Corrected basic handling of stack read support bqSBB Version 1.3.72 Release Notes --------------------------------- Calibration: Add bq27320 v0.08 voltage and temperature data memory parameters to allow calibration of voltage and current. bqSBB Version 1.3.71 Release Notes --------------------------------- Calibration: Modified CC Gain handling specifically for the bq34210 for current calibration bq79606: Minor updates to auto addresing algorithm Temproarily disabled baud rate switching Several minor updates to bq79606 GUI plugins GPC Packager: Added the GPCPackager to Project Mode bqSBB Version 1.3.69 Release Notes --------------------------------- Calibration: Add Battery and Pack Gain Scale Factor for bq9006 Parameter Q&A: Support for decimal numbers like temperature bq79606: Handling Negative cell voltages Start ADC measurement in Continuous loop when Continuous Cell Conversions is not enabled Show Hex values always for configuration registers bqSBB Version 1.3.68 Release Notes --------------------------------- bq9035: Added SHA-256 Authentication in Gauge Mode Multiply CapacityGain by factor of 4 bq79606: Code Refactoring and Table Device Addresing fix General Enhancements to Auto Addressing and updated to communication timing bqSBB Version 1.3.67 Release Notes --------------------------------- bq79606: Added a precision method