TSC ODV-2D英文使用说明书 (1).pdf

Online Data Validator 2D User’s Manual

T8204 and T8304 Printers

Printronix Auto ID Technology, Inc. makes no representations or warranties of any kind regarding this

material, including, but not limited to, implied warranties of merchantability and fitness for a particular

purpose. Printronix Auto ID Technology, Inc. shall not be held responsible for errors contained herein or

any omissions from this material or for any damages, whether direct, indirect, incidental or consequential,

in connection with the furnishing, distribution, performance or use of this material. The information in this

manual is subject to change without notice.

This document contains proprietary information protected by copyright. No part of this document may be

reproduced, copied, translated or incorporated in any other material in any form or by any means, whether

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not occur in an installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

Any change or modification to this product voids the user’s authority to operate it per FCC Part 15 Subpart

A Section 15.21 regulations.

Canada

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this

device must accept any interference, including interference that may cause undesired operation of the

device.

Technology Equipment.”

• EN 55024 — “Electromagnetic Immunity Requirements for Information Technology Equipment”

• EN 60950 — “Safety of Information Technology Equipment.”

Printronix Auto ID Technology, Inc. cannot accept responsibility for any failure to satisfy the protection

requirements resulting from a non-recommended modification of the product, including the fitting of

non-Printronix option cards.

This product has been tested and found to comply with the limits of Class A Information Technology

Equipment according to European standard EN 55022. The limits for Class A equipment were derived for

commercial and industrial environments to provide reasonable protection against interference with

licensed communication devices.

Taiwan

The Printronix Online Data Validator 2D gathers data per the ISO/ANSI method of verification to perform

practically all the industry standard bar code quality parameter calculations. These include all ISO/ANSI

The Printronix ODV2D gathers data and performs all ISO/ANSI method parameter calculations per the

ISO/IEC 15416 (1-D) and ISO/IEC 15415 (2-D), and ANSI X3.182-1990 methodologies with a few special

considerations and exceptions. The ODV2D also conforms to ISO/IEC 15426-1 and 15426-2 per the

requirements specified in Section 2 of both documents, with some exceptions.

The exceptions and considerations are related to the instrument’s design and mission. The design

incorporates a proprietary image scanner that has been assembled with a fixed focal length to produce a

accuracy of some grading parameters may be lower than identified in the standard.

The mission is to not only analyze bar code quality, but also to detect any printer failures, process failures

or media problems. For maximum performance and to conform to quality specifications, a fixed mounting

reflectance properties, the best print quality for that particular print method and material is achieved by

definition.

1. Final system tests are performed at the proper focus distance and at an angle of 27 degrees. Units

2. All ODV2D’s use the same light source with a wavelength of 624 +/- 10 nm. Therefore, any ISO/ANSI

The Defects calculation does not include the quiet zone area. A separate quiet zone check is implemented