7.NL.A.11.03.97.R1.P.CW6BC
Warranty (contd)
Agilent does not warrant that the
operation of Agilent products will be
uninterrupted or error free. If Agilent
is unable, within a reasonable time,
to repair or replace any product to a
condition as warranted, customer
will be entitled to a refund of the
purchase price upon prompt return of
the product.
Agilent products may contain
remanufactured parts equivalent to
new in performance or may have
been subjected to incidental use.
The warranty period begins on the
date of delivery or on the date of
installation if installed by Agilent. If
customer schedules or delays Agilent
installation more than 30 days after
delivery, warranty begins on the 31st
day from delivery.
Warranty does not apply to defects
resulting from (a) improper or
inadequate maintenance or
calibration, (b) software, interfacing,
parts or supplies not supplied by
Agilent, (c) unauthorized
modification or misuse, (d) operation
outside of the published
environmental specifications for the
product, or (e) improper site
preparation or maintenance.
TO THE EXTENT ALLOWED BY
LOCAL LAW, THE ABOVE
WARRANTIES ARE EXCLUSIVE
AND NO OTHER WARRANTY OR
CONDITION, WHETHER
WRITTEN OR ORAL, IS
EXPRESSED OR IMPLIED AND
AGILENT SPECIFICALLY
DISCLAIMS ANY IMPLIED
WARRANTIES OR CONDITIONS
OF MERCHANTABILITY,
SATISFACTORY QUALITY, AND
FITNESS FOR A PARTICULAR
PURPOSE.
Agilent will be liable for damage to
tangible property per incident up to
the greater of $300,000 or the actual
amount paid for the product that is
the subject of the claim, and for
damages for bodily injury or death,
to the extent that all such damages
are determined by a court of
competent jurisdiction to have been
directly caused by a defective
Agilent product.
TO THE EXTENT ALLOWED BY
LOCAL LAW, THE REMEDIES IN
THIS WARRANTY STATEMENT
ARE CUSTOMER’S SOLE AND
EXCLUSIVE REMEDIES.
EXCEPT AS INDICATED ABOVE,
IN NO EVENT WILL AGILENT
OR ITS SUPPLIERS BE LIABLE
FOR LOSS OF DATA OR FOR
DIRECT, SPECIAL, INCIDENTAL,
CONSEQUENTIAL (INCLUDING
LOST PROFIT OR DATA), OR
OTHER DAMAGE, WHETHER
BASED IN CONTRACT, TORT, OR
OTHERWISE.
For consumer transactions in
Australia and New Zealand: the
warranty terms contained in this
statement, except to the extent
lawfully permitted, do not exclude,
restrict or modify and are in addition
to the mandatory statutory rights
applicable to the sale of this product
to you.
Assistance
Product maintenance agreements and
other customer assistance agreements
are available for Agilent
Technologies products.
For any assistance, contact your
nearest Agilent Technologies Sales
and Service Office.
Safety Considerations (contd)
WARNING
INSTRUCTIONS FOR
ADJUSTMENTS WHILE
COVERS ARE REMOVED
AND FOR SERVICING ARE
FOR USE BY SERVICE-
TRAINED PERSONNEL
ONLY. TO AVOID
DANGEROUS ELECTRIC
SHOCK, DO NOT PERFORM
SUCH ADJUSTMENTS OR
SERVICING UNLESS
QUALIFIED TO DO SO.
WARNING
ANY INTERRUPTION OF THE
PROTECTIVE GROUNDING
CONDUCTOR (INSIDE OR
OUTSIDE THE PRODUCT'S
CIRCUITRY) OR
DISCONNECTING THE
PROTECTIVE EARTH
TERMINAL WILL CAUSE
A POTENTIAL SHOCK
HAZARD THAT COULD
RESULT IN PERSONAL
INJURY. (GROUNDING ONE
CONDUCTOR OF A TWO
CONDUCTOR OUTLET IS
NOT SUFFICIENT
PROTECTION.)
Whenever it is likely that the
protection has been impaired, the
instrument must be made inoperative
and be secured against any
unintended operation.
If this instrument is to be energized
via an autotransformer (for voltage
reduction) make sure the common
terminal is connected to the earthed
pole terminal (neutral) of the power
source.
Instructions for adjustments while
covers are removed and for servicing
are for use by trained-personnel only.
To avoid dangerous electric shock,
do not perform such adjustments or
servicing unless qualified to do so.
For continued protection against fire,
replace the line fuse(s) of the same
current rating and type (for example,
normal blow, time delay). Do not use
repaired fuses or short circuited
fuseholders.
Acoustic Noise Emissions
LpA<47 dB at operator position, at
normal operation, tested per
EN 27779. All data are the results
from type test.
Geräuschemission
LpA<47 dB am Arbeits
platz, normaler Betrieb, geprüft nach
EN 27779.
Die Angagen beruhen auf
Ergebnissen von Typenprüfungen.
