没有合适的资源?快使用搜索试试~ 我知道了~
FAS2700 - Replacing the NVMEM battery.pdf
需积分: 5 0 下载量 35 浏览量
2021-09-23
11:04:36
上传
评论
收藏 153KB PDF 举报
温馨提示
试读
13页
FAS2700 - Replacing the NVMEM battery
资源推荐
资源详情
资源评论
FAS2700 and AFF A220 systems
Replacing the NVMEM battery
The workflow diagram shows you the tasks involved in replacing the NVMEM battery.
Replacing the NVMEM battery
To replace an NVMEM battery in the system, you must remove the controller module from the system, open it, replace the
battery, and close and replace the controller module.
About this task
All other components in the system must be functioning properly; if not, you must contact technical support.
Steps
1. Shutting down the impaired controller on page 2
1
215-12721_2019-11_en-us November 2019 Copyright
©
2019 NetApp, Inc. All rights reserved.
Web: www.netapp.com • Feedback: doccomments@netapp.com
2. Opening the system on page 4
3. Replacing the NVMEM battery on page 6
4. Reinstalling the controller module on page 7
5. Running system-level diagnostics on page 8
6. Switching back aggregates in a two-node MetroCluster configuration on page 11
7. Completing the replacement process on page 12
Shutting down the impaired controller
You can shut down or take over the impaired controller using different procedures, depending on the storage system hardware
configuration.
Shutting down the node
To shut down the impaired node, you must determine the status of the node and, if necessary, take over the node so that the
healthy node continues to serve data from the impaired node storage.
Before you begin
• If you have a cluster with more than two nodes, it must be in quorum. If the cluster is not in quorum or a healthy node shows
false for eligibility and health, you must correct the issue before shutting down the impaired node.
ONTAP 9 System Administration Reference
Steps
1. If the impaired node is part of an HA pair, disable automatic giveback from the console of the healthy node:
storage failover modify -node local -auto-giveback false
2. Take the impaired node to the LOADER prompt:
If the impaired node is displaying... Then...
The LOADER prompt Go to the next step.
Waiting for giveback... Press Ctrl-C, and then respond y when prompted.
System prompt or password prompt
(enter system password)
Take over or halt the impaired node:
• For an HA pair, take over the impaired node from the healthy node:
storage failover takeover -ofnode impaired_node_name
When the impaired node shows Waiting for giveback..., press Ctrl-C, and then
respond y.
• For a stand-alone system:
system node halt impaired_node_name
3. If the system has only one controller module in the chassis, turn off the power supplies, and then unplug the impaired node's
power cords from the power source.
2
FAS2700 systems: Replacing the NVMEM battery
Shutting down a node in a two-node MetroCluster configuration
To shut down the impaired node, you must determine the status of the node and, if necessary, switch over the node so that the
healthy node continues to serve data from the impaired node storage.
About this task
You must leave the power supplies turned on at the end of this procedure to provide power to the healthy node.
Steps
1.
Check the MetroCluster status to determine whether the impaired node has automatically switched over to the healthy node:
metrocluster show
2.
Depending on whether an automatic switchover has occurred, proceed according to the following table:
If the impaired node... Then...
Has automatically switched over Proceed to the next step.
Has not automatically switched over Perform a planned switchover operation from the healthy node:
metrocluster switchover
Has not automatically switched over,
you attempted switchover with the
metrocluster switchover
command, and the switchover was
vetoed
Review the veto messages and, if possible, resolve the issue and try again. If you are unable to
resolve the issue, contact technical support.
3. Resynchronize the data aggregates by running the metrocluster heal -phase aggregates command from the
surviving cluster.
Example
controller_A_1::> metrocluster heal -phase aggregates
[Job 130] Job succeeded: Heal Aggregates is successful.
If the healing is vetoed, you have the option of reissuing the metrocluster heal command with the -override-vetoes
parameter. If you use this optional parameter, the system overrides any soft vetoes that prevent the healing operation.
4. Verify that the operation has been completed by using the metrocluster operation show command.
Example
controller_A_1::> metrocluster operation show
Operation: heal-aggregates
State: successful
Start Time: 7/25/2016 18:45:55
End Time: 7/25/2016 18:45:56
Errors: -
5. Check the state of the aggregates by using the storage aggregate show command.
Shutting down the impaired controller
3
剩余12页未读,继续阅读
资源评论
黑山老腰断了
- 粉丝: 5
- 资源: 427
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
最新资源
- 投票系统开发案列优质学习资料资源工具与案列应用场景开发文档教程资料.txt
- 51单片机应用系统典型模块开发大全(第3版)资料
- 汇编语言开发案列优质学习资料资源工具与案列应用场景开发文档教程资料.txt
- Python + OpenCV开发案列优质学习资料资源工具与案列应用场景开发文档教程资料.txt
- 儿童节小游戏开发案列优质学习资料资源工具与案列应用场景开发文档教程资料.txt
- MySQL开发案列优质学习资料资源工具与案列应用场景开发文档教程资料.txt
- MATLAB仿真案列优质学习资料资源工具与案列应用场景开发文档教程资料.txt
- MATLAB优质学习资料资源工具与案列应用场景开发文档教程资料.txt
- 4319447015972566022ssm城市交通海量数据管理系统.zip
- 前端开发实例优质学习资料资源工具与案列应用场景开发文档教程资料.txt
资源上传下载、课程学习等过程中有任何疑问或建议,欢迎提出宝贵意见哦~我们会及时处理!
点击此处反馈
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功