没有合适的资源?快使用搜索试试~ 我知道了~
本科毕业设计---基于单片机智能火灾报警系统的设计.doc
1 下载量 8 浏览量
2023-07-09
08:27:55
上传
评论 1
收藏 2.48MB DOC 举报
温馨提示
试读
42页
本科毕业设计---基于单片机智能火灾报警系统的设计.doc
资源推荐
资源详情
资源评论
本科毕业设计
题 目 基 于 单 片 机 智 能 火 灾 报 警 系 统 的 设 计
学生姓名
专业名称 电子电气工程学院 2011 级通信工程
指导教师
2015 年 5 月 8 日
教学单位
学生学号
编 号
基 于 单 片 机 智 能 火 灾 报 警 系 统 的 设 计
摘要:伴随着时代不断的进步,人们越来越多的使用电子类设备,无论是家庭还
是工厂使用的电器都越来越多,随之而来的是因为电器的不当使用所引起的火灾
也与日俱增,我们的国家每年因为所用电器造成的火灾而损失很多。火灾不仅带
来了物品财产上的损失,也带给了我们失去亲人的悲痛。所以研制出一款针对于
家庭、宿舍等小环境的火灾报警系统是非常重要的。
本次设计以传感器和单片机作为烟雾报警器设计的核心器件,配合其它器件
即可实现烟雾和温度报警等功能。设计中单片机选用 STC89C52作为控制器件,传
感器选用 MQ-2型半导体可燃气体敏感元件烟雾传感器实现烟雾的检测。论文主要
针对火灾报警系统中的各个组成部分及功能进行了详细的介绍和说明,在文章第
二部分有该篇论文的总体方案设计,可设置烟雾浓度和高温报警值,当烟雾传感
器检测到火灾释放的烟雾时,信号由 ADC0832进行处理模数转化再到单片机进行
处理,当检测到浓度超标时,蜂鸣器会发出滴滴的报警声。同时,此系统还可以
检测温度,火灾发生往往环境温度会升高,当检测到温度超过设定的报警温度时
候,蜂鸣器也将产生报警。第三四部分有很详细的系统软硬件的分析与讲解,还
附有系统的流程图和其主控电路及外围设备电路之间的接口连接方式,最后,对
系统在电路调试中出现的问题进行了分析与总结。
关键字:单片机;传感器;烟雾报警器
Design of fire alarm system for single chip computer
Abstract: Along with the time progress, people more and more use of electronic
equipment, whether it is family and factory use appliances are more and more, the
attendant is caused by the improper use of electrical fire is also increasing, our country
every year because the electricity is caused by the fire and lose a lot. Fire not only
brought goods property losses, but also bring us the grief of losing loved ones. So
developed a needle for families, dormitories and other small environment of the fire
alarm system is very important.
The design of the sensor and single-chip microcomputer as the core design of a
smoke alarm devices, with other devices can realize the temperature and smoke alarm
etc. function. Design of MCU choose STC89C52 as control devices and sensors use
mq-2 semiconductor combustible gas sensitive element smoke sensor to achieve
smoke detection. Paper for fire alarm system in each part and function of a detailed
introduction and explanation, in the article the second part is the overall design of the
thesis can be set up smoke concentration and high temperature alarm value, when the
smoke sensor to detect fires release smoke, signal by ADC0832 were processing
analog-to-digital conversion to single chip to carry on processing, when the detected
exceeding, the buzzer will drop the issue alarm sound. At the same time, the system
can detect the temperature, fires often environmental temperature will rise. When the
detected temperature exceeds the set temperature alarm, buzzer will also generate an
alarm. The third part has a very detailed analysis of the software and hardware of the
system and explain the, is accompanied by the interface between the flow chart of the
system and its main control circuit and peripheral circuit connection mode. Finally, the
problems appeared in system debugging of circuit are analyzed and summarized.
Key words: sensor ; MCU ; The smoke alarm
目 录
一 毕设正文 .............................................................................................1
1 绪论 .......................................................................................................1
1.1 课题背景 ...................................................................................1
1.2 烟雾报警器的国内外现状 .......................................................1
1.3 烟雾报警器的发展趋势 ...........................................................2
2 总体方案设计 .......................................................................................3
2.1 烟雾检测传感器选型 ...............................3
2.2 烟雾传感器关于报警的介绍 .........................5
2.3 单片机选型 .......................................5
2.3.1 STC89C52 单片机简介 .............................5
2.3.2 单片机的引脚功能描述 ...........................6
2.3.3 温度采集模块 ...................................8
3 系统的硬件电路 ...................................................................................9
3.1 单片机最小系统 .......................................................................9
3.2 单片机的时钟电路与复位电路设计 ...................9
3.3 烟雾检测 AD 采集电路 .............................10
3.4 显示模块 ........................................11
3.5 声音报警电路 ....................................11
3.6 按键控制电路 ....................................12
3.7 电源模块 ........................................12
3.8 温度传感器(DS18B20)电路 .........................13
3.8.1 DSl8B20 简介 ...................................13
3.8.2 18B20 接口电路 .................................15
4 系统软件的设计及流程图 .................................................................17
5 电路调试中遇到的问题及总结 .........................................................18
参考文献 ...................................................................................................19
谢 辞.......................................................................................................20
二 附录 .....................................................................................................21
1 总体原理图设计 ....................................21
2 部分程序源代码 ....................................22
3 实物图 ............................................33
4 开题报告 ..........................................34
5 结题报告 ..........................................35
6 答辩报告 ..........................................36
剩余41页未读,继续阅读
资源评论
黑色的迷迭香
- 粉丝: 724
- 资源: 4万+
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功