毕设&课设&项目&实训-CSL大创项目的数据采集板.zip

/** ****************************************************************************** * @file system_stm32f1xx.c * @author MCD Application Team * @brief CMSIS Cortex-M3 Device Peripheral Access Layer System Source File. * * 1. This file provides two functions and one global variable to be called from * user application: * - SystemInit(): Setups the system clock (System clock source, PLL Multiplier * factors, AHB/APBx prescalers and Flash settings). * This function is called at startup just after reset and * before branch to main program. This call is made inside * the "startup_stm32f1xx_xx.s" file. * * - SystemCoreClock variable: Contains the core clock (HCLK), it can be used * by the user application to setup the SysTick * timer or configure other parameters. * * - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must * be called whenever the core clock is changed * during program execution. * * 2. After each device reset the HSI (8 MHz) is used as system clock source. * Then SystemInit() function is called, in "startup_stm32f1xx_xx.s" file, to * configure the system clock before to branch to main program. * * 4. The default value of HSE crystal is set to 8 MHz (or 25 MHz, depending on * the product used), refer to "HSE_VALUE". * When HSE is used as system clock source, directly or through PLL, and you * are using different crystal you have to adapt the HSE value to your own * configuration. * ****************************************************************************** * @attention * * <h2><center>&copy; Copyright (c) 2017 STMicroelectronics. * All rights reserved.</center></h2> * * This software component is licensed by ST under BSD 3-Clause license, * the "License"; You may not use this file except in compliance with the * License. You may obtain a copy of the License at: * opensource.org/licenses/BSD-3-Clause * ****************************************************************************** */ /** @addtogroup CMSIS * @{ */ /** @addtogroup stm32f1xx_system * @{ */ /** @addtogroup STM32F1xx_System_Private_Includes * @{ */ #include "stm32f1xx.h" /** * @} */ /** @addtogroup STM32F1xx_System_Private_TypesDefinitions * @{ */ /** * @} */ /** @addtogroup STM32F1xx_System_Private_Defines * @{ */ #if !defined (HSE_VALUE) #define HSE_VALUE 8000000U /*!< Default value of the External oscillator in Hz. This value can be provided and adapted by the user application. */ #endif /* HSE_VALUE */ #if !defined (HSI_VALUE) #define HSI_VALUE 8000000U /*!< Default value of the Internal oscillator in Hz. This value can be provided and adapted by the user application. */ #endif /* HSI_VALUE */ /*!< Uncomment the following line if you need to use external SRAM */ #if defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F103xE) || defined(STM32F103xG) /* #define DATA_IN_ExtSRAM */ #endif /* STM32F100xE || STM32F101xE || STM32F101xG || STM32F103xE || STM32F103xG */ /*!< Uncomment the following line if you need to relocate your vector Table in Internal SRAM. */ /* #define VECT_TAB_SRAM */ #define VECT_TAB_OFFSET 0x00000000U /*!< Vector Table base offset field. This value must be a multiple of 0x200. */ /** * @} */ /** @addtogroup STM32F1xx_System_Private_Macros * @{ */ /** * @} */ /** @addtogroup STM32F1xx_System_Private_Variables * @{ */ /* This variable is updated in three ways: 1) by calling CMSIS function SystemCoreClockUpdate() 2) by calling HAL API function HAL_RCC_GetHCLKFreq() 3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency Note: If you use this function to configure the system clock; then there is no need to call the 2 first functions listed above, since SystemCoreClock variable is updated automatically. */ uint32_t SystemCoreClock = 16000000; const uint8_t AHBPrescTable[16U] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9}; const uint8_t APBPrescTable[8U] = {0, 0, 0, 0, 1, 2, 3, 4}; /** * @} */ /** @addtogroup STM32F1xx_System_Private_FunctionPrototypes * @{ */ #if defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F103xE) || defined(STM32F103xG) #ifdef DATA_IN_ExtSRAM static void SystemInit_ExtMemCtl(void); #endif /* DATA_IN_ExtSRAM */ #endif /* STM32F100xE || STM32F101xE || STM32F101xG || STM32F103xE || STM32F103xG */ /** * @} */ /** @addtogroup STM32F1xx_System_Private_Functions * @{ */ /** * @brief Setup the microcontroller system * Initialize the Embedded Flash Interface, the PLL and update the * SystemCoreClock variable. * @note This function should be used only after reset. * @param None * @retval None */ void SystemInit (void) { /* Reset the RCC clock configuration to the default reset state(for debug purpose) */ /* Set HSION bit */ RCC->CR |= 0x00000001U; /* Reset SW, HPRE, PPRE1, PPRE2, ADCPRE and MCO bits */ #if !defined(STM32F105xC) && !defined(STM32F107xC) RCC->CFGR &= 0xF8FF0000U; #else RCC->CFGR &= 0xF0FF0000U; #endif /* STM32F105xC */ /* Reset HSEON, CSSON and PLLON bits */ RCC->CR &= 0xFEF6FFFFU; /* Reset HSEBYP bit */ RCC->CR &= 0xFFFBFFFFU; /* Reset PLLSRC, PLLXTPRE, PLLMUL and USBPRE/OTGFSPRE bits */ RCC->CFGR &= 0xFF80FFFFU; #if defined(STM32F105xC) || defined(STM32F107xC) /* Reset PLL2ON and PLL3ON bits */ RCC->CR &= 0xEBFFFFFFU; /* Disable all interrupts and clear pending bits */ RCC->CIR = 0x00FF0000U; /* Reset CFGR2 register */ RCC->CFGR2 = 0x00000000U; #elif defined(STM32F100xB) || defined(STM32F100xE) /* Disable all interrupts and clear pending bits */ RCC->CIR = 0x009F0000U; /* Reset CFGR2 register */ RCC->CFGR2 = 0x00000000U; #else /* Disable all interrupts and clear pending bits */ RCC->CIR = 0x009F0000U; #endif /* STM32F105xC */ #if defined(STM32F100xE) || defined(STM32F101xE) || defined(STM32F101xG) || defined(STM32F103xE) || defined(STM32F103xG) #ifdef DATA_IN_ExtSRAM SystemInit_ExtMemCtl(); #endif /* DATA_IN_ExtSRAM */ #endif #ifdef VECT_TAB_SRAM SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM. */ #else SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH. */ #endif } /** * @brief Update SystemCoreClock variable according to Clock Register Values. * The SystemCoreClock variable contains the core clock (HCLK), it can * be used by the user application to setup the SysTick timer or configure * other parameters. * * @note Each time the core clock (HCLK) changes, this function must be called * to update SystemCoreClock variable value. Otherwise, any configuration * based on this variable will be incorrect. * * @note - The system frequency computed by this function is not the real * frequency in the chip. It is calculated based on the predefined * constant and the selected clock source: * * - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*) * * - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**) * * - If SYSCL