x3m使用uart工具手动一步一步烧写固件，所包含的文件

NOTICE: fast_boot:0 S F L O NOTICE: efuse cpu_cfg = 0 W NOTICE: Booting Trusted Firmware NOTICE: BL1: v1.4(release):HR-ROM-Rel-v1.1-141-ga91d4dd-dirty NOTICE: BL1: Built : 11:24:44, Oct 23 2019 NOTICE: Waiting connect ... NOTICE: ******** Load Next FWU By UART ******** NOTICE: Waiting for a moment ... CCCCCCCCCCCCCCCCCC Starting xmodem transfer. Press Ctrl+C to cancel. Transferring spl-uart-secure.bin... 100% 53 KB 17 KB/sec 00:00:03 0 Errors NOTICE: ## Total Size = 0x0000d580 = 54656 Bytes Auth pass NOTICE: bl1_main exit SPL cold boot flow check_reset_state (0): wakeup address = 0x0, hw wakeup status = 0x0, wakeup src=0x100 patch for sys_pll 1200 with 100M eth SFLOW_INIT CHIP ID:P63V45/WAFER: W04/ X: X23/ Y: Y11 secondary_jump_to_spl: secure chip flow X3 SPL : secondary core wake up and jump to spl done (cpu_core_cfg=0) SFLOW_FIN_HW_A U-Boot SPL 2018.09-00872-g798ab56e1b (Jun 21 2021 - 17:45:37 +0800) SPACC Init - ID: (00000061) SPL uart boot mode only ***** using efuse ddr type ****** ddr_type = 1 (LPDDR4) CCCCCCC Starting ymodem transfer. Press Ctrl+C to cancel. Transferring SAMSUNG-LPDDR4-3200-110-ddr.bin... 100% 78 KB 7 KB/sec 00:00:10 1 Errors ymodem Loaded 80384 bytes ***** using efuse vendor type ***** uart/ap boot or no multifle ddr daterate: 2666 update uart ddr vendor:0x3, type:0x1, freq:0xc80 ### SAMSUNG DDR ### ddr_type = 1, ddr_vendor=3, ddr_freq=3200 dram_pll_init sscg disabled uart load ddrc src_addr: 00, load_addr: 80291158, src_len: 920 [DDR INFO] ==ddr_release_info== [DDR INFO] VERSION: develop [DDR INFO] BUILD: 2021-06-21-17:45 [DDR INFO] GIT COMMIT: 798ab56e1bf74c8f3438275ab121bdea0fc65335 [DDR INFO] GIT TIME: Mon, 21 Jun 2021 17:30:57 +0800 [DDR INFO] ==ddr_features== [DDR INFO] RDBI: 0 [DDR INFO] WDBI: 1 [DDR INFO] InlineECC: 0 [DDR INFO] DM: 1 [DDR INFO] DDC: 1 [DDR INFO] SSCG: 0 [DDR INFO] BOARD: XS_ENABLE [DDR INFO] ddr_controller_cfg done ATxSlewRate : 15f ATxImpedance : 7f TxSlewRate : 19f TxOdtDrvStren : 600 TxImpedanceCtrl : e3f CalDrvStr0 : 11 VrefInGlobal : 104 uart/ap multifile board type:0 board_type = 4 (CUSTOMER_BOARD) [DDR INFO] dwc_ddrphy_train start uart load imem1 src_addr: 00, load_addr: 80280358, src_len: 8000 executing 1D fw executing 2D fw lpddr4 mr5 (rank=0x0, MRCTRL0=0x11, MRSTAT=0x0, MSTR=0x81080020) : 0x10100 0x10100 0x10100 0x10100 lpddr4 mr8 (rank=0x0, MRCTRL0=0x11, MRSTAT=0x0, MSTR=0x81080020) : 0x101000 0x101000 0x101000 0x101000 get_ddr_mr_info:cs_num=1, mr5=0x1, mr8=0x10 Set QoS. total_sz = 2048 ymodem: start to receive pkg file... CCCCC Starting ymodem transfer. Press Ctrl+C to cancel. Transferring boot_uart_secure.pkg... 100% 1085 KB 12 KB/sec 00:01:25 1 Errors ymodem Loaded 1111552 bytes ymodem load u-boot: dest_addr=, len=914432 error: ymodem fail to load warm boot spl: dest_addr=, len=0 ymodem load bl31: dest_addr=, len=82944 SFLOW_AUTH_BL31 verify signature of header: verify ok! verify signature of image: verify ok! warning: ymodem fail to load bpu image: dest_addr=, len=0 clear keybank!!!! Trying to boot from RAM SPL: bl31 will jump to u-boot or other entry (0x4000000) SFLOW_CLR_KEY SFLOW_REG_LD install_portal copy portal install_portal call smc and jump to bl31 cold entry(0x0) U-Boot 2018.09 (Aug 09 2022 - 11:03:54 +0800) Model: Hobot XJ3 Soc Board DRAM: system DDR size: 0x7fe00000 2 GiB MMC: dwmmc@A5010000: 0 (eMMC) In: serial@a5000000 Out: serial@a5000000 Err: serial@a5000000 Net: Warning: ethernet@A5014000 (eth0) using random MAC address - 16:c2:2c:90:90:89 eth0: ethernet@A5014000 Disable cnn cores .. base board type: X3 SDB bootmode: UART disable watchdog success ! Hobot> Hobot> Hobot> Hobot> Hobot><INTERRUPT> Hobot>