Setup_V3.0.17.10_Targets.zip

#################################################################################################### # V E R S I O N I N F O R M A T I O N # # Module: BASIC # Date: Tue Feb 25 10:54:48 2020 # # This file lists actual release notes for a RC series 30 module. # #################################################################################################### # (c) Copyright by BOSCH REXROTH AG, all rights reserved #################################################################################################### **************************************************************************************************** * BASIC V01.99: **************************************************************************************************** +-----------------+ | Trouble Reports | +-----------------+ #2300 (BASIC) * FIX: ECC trap issue of DFLASH in RC4-5/30, Issue:If ignition is ON and switch OFF while writing data into DFLASH in initialization phase of the ECU.This was causing DFLASHH ECC Trap. if ECC trap occurred, it will continuously resets the ECU and this error is not stored in error memory. Application is not executed in this situation. **************************************************************************************************** * BASIC V01.98: **************************************************************************************************** +-----------------+ | Trouble Reports | +-----------------+ #2269 (BASIC): * CHG: New defines added for the ch2Rev_u8 parameter in the sent_cfgFDDecode() function to avoid the confusion while reading the channel 2 nibbles in reversed/non-reversed manner. (see sent_api.h file) #2272 (BASIC): * CHG: In sent_cfgFDDecode() function the 16-bit counter length is not supported according to the SAE J2716-2010-01 standard. So it is removed. #2286 (BASIC): * ADD: The SENT Fast Data FIFO Counter value(counter_u8) and the Message Status (msgStat_u8) nibble was not updated previously. It is updated now. **************************************************************************************************** * BASIC V01.97: **************************************************************************************************** +-------+ | Tasks | +-------+ #2287 (BASIC ): * ADD: basic module is baselined with tag version with V01.97 for trap bug fixes during CAN wakeup and continuous reset. **************************************************************************************************** * BASIC V01.96: **************************************************************************************************** +-----------------+ | Trouble Reports | +-----------------+ #2259 (BASIC): * CHG: function "ee_getStatus" modified for the condition "eeprom queue handling disable" during afterrun **************************************************************************************************** * BASIC V01.95: **************************************************************************************************** +-----------------+ | Change Requests | +-----------------+ #2222 (BASIC): * ADD: Internal Monitoring of Voltage difference between UBAT and VP_1 is enabled for RC4-5/30. When VP_1 is ON, if the voltage difference is more than 6V with respect to UBAT then a error will be set. #2214 (BASIC): *CHG: In RC4-5/30(old), MOCSOP feature was not enabled, Due this there was different behavior of sys_setVp in RC4-5/30 hardware release(old) and hardware release RL2. MOCSOP feature is enabled, so that sys_setVP behavior is same for all hardware release. ........ **************************************************************************************************** * BASIC V01.94A: **************************************************************************************************** +-----------------+ | Change Requests | +-----------------+ #2222 (BASIC): * ADD: Internal Monitoring of Voltage difference between UBAT and VP_1 is enabled for RC4-5/30. When VP_1 is ON, if the voltage difference is more than 6V with respect to UBAT then a error will be set. #2214 (BASIC): *CHG: In RC4-5/30(old), MOCSOP feature was not enabled, Due this there was different behavior of sys_setVp in RC4-5/30 hardware release(old) and hardware release RL2. MOCSOP feature is enabled, so that sys_setVP behavior is same for all hardware release. ........ **************************************************************************************************** * BASIC V01.94: **************************************************************************************************** +-----------------+ | Trouble Reports | +-----------------+ #2216 (BASIC): * FIX: In V03.00, VP_1 was above 3.5V before calling sys_setvp(VP_1,ON). Now VP_1 is less than 2V before calling sys_setVP(VP_1,ON) **************************************************************************************************** * BASIC V01.93: **************************************************************************************************** +-----------------+ | Change Requests | +-----------------+ #2205 (BASIC): * CHG: In CPM API the DIAG default parameter values are not set any more in case of a new SW name. #2144 (BASIC DIAG): * ADD: Earlier, No Monitoring for 3.3V internal Voltage. 3.3V internal voltage monitoring is enabled. #2139 (BASIC): * ADD: MOCSOP features is added to RC4-5/30 RL2 **************************************************************************************************** * BASIC V01.90: **************************************************************************************************** +-----------------+ | Trouble Reports | +-----------------+ #2158 (BASIC): * FIX: The state evaluation of VP's can be failed through an interrupt request. +-------+ | Tasks | +-------+ #1861 (BASIC): * ADD: The LSAFOUT functionality is added for RC10-10 #1698 (BASIC DIAG TEMPLATE): * ADD: Module SENT is added for RC10-10. **************************************************************************************************** * BASIC V01.84A: **************************************************************************************************** +-----------------+ | Trouble Reports | +-----------------+ #2158 (BASIC): * FIX: The state evaluation of VP's can be failed through an interrupt request. **************************************************************************************************** * BASIC V01.84: **************************************************************************************************** +-----------------+ | Trouble Reports | +-----------------+ #1848 (BASIC): * CHG: SPI error handling changed to solve the monitoring error 0xE08/8 **************************************************************************************************** * BASIC V01.83: **************************************************************************************************** +-----------------+ | Trouble Reports | +-----------------+ #2103 (BASIC): * FIX: If in safout mode POH more than one HS is configured and all configured HS's are deactivated the behaviour after call of safout_resetError() is not correct...some outputs are switched on even though that not all outputs are previously switched off. #1737 (BASIC): * FIX: Logging of temperature profile (Temperature Depending Operating Hours = TDOH) old behavior: Wrong temperature classification values can be calculated if ECU is restarted via software reset. new behavior: