施奈德plc 编程软件twidosoft V3.5

TWIDOSOFT VERSION 3.5 RELEASE NOTIFICATION This document contains the following sections: 1. OVERVIEW 2. RECOMMENDED SYSTEM REQUIREMENTS 3. NEW FEATURES 4. LATE NOTICES 5. TWIDO CONTROLLERS OPERATING SYSTEM INFORMATION 6. TWIDOSOFT's FUNCTIONAL LEVELS INFORMATIONS =============================================================== 1. OVERVIEW Please read this information before working with Twido products. For general features, please refer to the online help delivered on the TwidoSoft CD and installed with the control software. =============================================================== 2. RECOMMENDED SYSTEM REQUIREMENTS A] Software - PC-compatible computer with a 300 MHz Pentium processor, - Windows 98 Second Edition, Windows 2000 or Windows XP, - Microsoft Internet Explorer 5.0 or 4.0 with HTML Help Installation and Update Package (Hhupd.exe) 1.32, - TCP/IP protocol installed, - In case of a firewall is installed on the PC-compatible computer, you must let free the local addresses on the ports between 27700 and 27709, - 128 MB of RAM, - 40 MB of hard drive space. Twidosoft doesn't work on Windows emulators. B] Connection to Twido controllers - RS232 with a DB9 connector, - USB port, if the PC-compatible computer is under Windows 2000 or Windows XP, and then the TSX PCX 3030 cable, - BlueTooth connection through the VW3A8114 dongle on the Twido controller, and through the BlueTooth key on the PC if it isn't BlueTooth inside. - Ethernet using the port 3 of the new Twido controller TWDLCAE40DRF, or using the Ethernet enabler TwidoPort ref 499TWD01100. - Modem: It's possible to use a modem connected to the PC-compatible computer. You must install the modem under the Windows operating system, and then select the modem by the sequence: "File" menu, and then "preferences" of Twidosoft. =============================================================== 3. NEW FEATURES The V3.5 version of Twidosoft allows new features like: - The analogic module TWDAMM6HT is available in the expansion configurator. - Macro Drive CANopen are available for ATV71 drive controller. =============================================================== 4. LATE NOTICES DOCUMENTATION The documentation files are available in the "DOC" directory at the root of the Twidosoft CD. Software reference guide : TwdoSOFT.pdf, TwdoSW.pdf Hardware reference guide : TwdoHW.pdf Assistant executive loader : Twel.pdf Modem communication : TWIDO_S1013_vA_modem.pdf RUNNING MULTIPLE INSTANCES OF TWIDOSOFT ON THE SAME PC TwidoSoft is not designed to run multiple instances of the software on a single PC. ON LINE HELP INDEX PREPARATION When you use the on line help index, if a message appears to indicate the index creation each time, and your PC-compatible computer operation system is Windows XP, then check the directory ..\Twidosoft\bin, in order to verify if you have writing rights in this directory. LADDER EDITOR If you use the function keys (F2 to F12, or icon selection) to select the object you want to insert in a rung, this key will be active for only one insertion. To make multiple insertions, use the association with the Ctrl key, then the effect of the function key (or icon selection) will be kept. HOW TO USE ASCII STRING IN A PROGRAM To assign an ASCII string to internal memory words, proceed as below : [%MW0 := "BO"] [%MW1 := "NJ"] [%MW2 := "OU"] [%MW3 := "R "] CHANGE BASE CONTROLLER TYPE FIRST Validation and analysis are made with respect to the controller type. It is recommended that you start your application development by selecting the target Controller type first. In this way, your system configuration will only consider the appropriate functions and maximum limitations. MODEM MANAGEMENT BY THE CONTROLLER When a modem is configured on a communication port inside the application, the Twido controller sends an initialization string (HAYES protocol) to the modem at power up. AS-INTERFACE MODULE MANAGEMENT (TWD NOI 10M3) Twidosoft offers two screens for the AS-Interface master module management. A configuration screen and a debug screen. The debug screen shows in connected mode, at the bottom, red information to indicate a non active state, but not an error, as defined in the IEC standard IEC 62026-2 (2000-07). AS-Interface SAFETY PRODUCTS IMPLEMENTATION: - The A2SI integrated circuit version of the AS-Interface safety slaves must be higher or equal to V3-7 (Rev C) . All the Schneider AS-Interface safety slaves ASISSLxx implement the V3-7 (Rv C) version since week 22 of year 2003. - For the ASISSLC1/ASISSLC2 products, the cable length connected to the M12 has to be stricly less than 3meters (ex: 2m). - Take into account the Schneider EMC manual recommendations, especially: . the AS-Interface cable and inout/output cables must be far enough from the power cables. . connect the earth to the Gnd AS-Interface power supply plug ( connector called Gnd or Shd near the ASI+/ASI-), connect the AS-Interface master Gnd and the AS-Interface safety monitor PE. CLEARING CONTROLLER MEMORY There may come a time when you want to initialize the controller memory to the original factory settings. This can be accomplished in one of two ways. First, you can use TwidoSoft and select "Erase" from the "Controller" main menu. From the Erase dialog, select "Erase all". The second method is to use the operator display (TWD XCP ODC or ODM). Simply depress and hold any of the keys and power cycle the unit. When power is restored release the key and you will note that the controller is in NCF (non-configured mode). REAL TIME CLOCK UPDATE The RTC update using the system bits and words must be done using the following sequence: - Set to 1 the %S50 (disables the date and time update by the operating system), - Update system words %WS50 to %SW53 (year, month, day, hour, ...), - Update the system word %SW60 with the correction factor written on the RTC accessory (TWD XCP RTC), - Set to 0 the %S50. PROGRAM ANALYSIS Missing point from Program analysis: - Do not leave empty lines between a subroutine (%SR1:), label (%L1:), or grafcet definition (=*= 1) and the initial instruction of that section. USER MANUAL CORRECTION The instruction "LDN %SW8x:X4" allows to know if the CAN_CMD instruction is correctly executed before sending another command. =============================================================== 5. TWIDO CONTROLLERS OPERATING SYSTEM INFORMATION - This CD contains the files of TWIDO controllers operating systems for version v1.12 to v3.5 - These operating systems can be transferred by means of the OS loader, available via the "Tools" menu of TWIDOSOFT. - In order to obtain the latest product functions it is recommended to transfer the most recent compatible version. The compatibility table below shows the different OS software versions associated with the technology bases of controllers: TABLE: Technology Base OS Software Versions Compact: TWDLCAA10DRF SV1.12, SV2.01, SV2.6, SV3.0, SV3.2, SV3.5 TWDLCAA16DRF SV1.12, SV2.01, SV2.6, SV3.0, SV3.2, SV3.5 TWDLCAA24DRF SV1.12, SV2.01, SV2.6, SV3.0, SV3.2, SV3.5 Modular: TWDLMDA20DUK SV1.12, SV2.01, SV2.6, SV3.0, SV3.2, SV3.5 TWDLMDA20DTK SV1.12, SV2.01, SV2.6, SV3.0, SV3.2, SV3.5 TWDLMDA20DRT SV1.12, SV2.01, SV2.6, SV3.0, SV3.2, SV3.5 TWDLMDA40DUK SV1.12, SV2.01, SV2.6, SV3.0, SV3.2, SV3.5 TWDLMDA40DTK SV1.12, SV2.01, SV2.6, SV3.0, SV3.2, SV3.5 TWDLCAA40DRF SV3.0, SV3.2, SV3.5 TWDLCAE40DRF SV3.0, SV3.2, SV3.5 OS file example: The binary file name of the TWDLCAA16DRF SV1.12 controller will be: TWIDO16_V0112.TFW; The binary file name of the TWD