前端开发美信射频前端开发板开发资料美信射频前端开发板开发资料资源-CSDN文库

共1个文件

pdf：1个

前端开发

需积分: 5 114 浏览量 2024-04-20 17:28:52 上传评论收藏 773KB RAR 举报

资源推荐

资源详情

资源评论

收起资源包目录

1863099.rar （1个子文件）

MAX2828EVKIT-MAX2829EVKIT.pdf 958KB

General Description

The MAX2828/MAX2829 evaluation kits (EV kits) simpli-

fy the testing of the MAX2828/MAX2829. The EV kits

provide 50Ω SMA connectors for all RF and baseband

inputs and outputs. Differential-to-single-ended and sin-

gle-ended-to-differential line drivers are provided to

convert the differential I/Q baseband inputs and out-

puts of the MAX2828/MAX2829 to single-ended ports.

The EV kits simplify evaluation of the receive and trans-

mit performance in the corresponding 802.11x bands.

Features

♦ On-Board Line Drivers and Voltage Reference

♦ 50Ω SMA and BNC Connectors on All RF and

Baseband Ports

♦ PC Control Software Available at www.maxim-ic.com

♦ 3-Wire Serial Interface

Evaluate: MAX2828/MAX2829

MAX2828/MAX2829 Evaluation Kits

________________________________________________________________ Maxim Integrated Products 1

DESIGNATION

QTY

DESCRIPTION

C1 1

0.5pF ±0.1pF 0402 capacitor

Murata GRM1555C1HR50B

C2 1

8.2pF ±0.1pF 0402 capacitor

Murata GRM1555C1H8R2B

C3, C66 2

1.0µF ±10% 0402 capacitors

Murata GRM155R60J105K

C4 1

1.0pF ±0.1pF 0402 capacitor

Murata GJM1555C1H1R0B

C5, C7, C10, C11,

C17, C18, C21,

C22, C29, C35,

C37, C40, C42,

C43, C45, C46,

C50, C52, C54,

C59, C60

0.1µF ±10% 0402 capacitors

Murata GRM1555R61A104K

C6, C9, C16, C19,

C20, C23–C28,

C30, C32, C36,

C38, C41, C56,

C57, C58

0.01µF ±10% 0402 capacitors

Murata GRM155R71C103K

C12, C13 2

1.8pF ±0.1pF 0402 capacitors

Murata GRM1555C1H1R8B

C14, C15 2

1.2pF ±0.1pF 0402 capacitors

Murata GJM1555C1H1R2B

19-3470; Rev 0; 10/04

For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at

1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com.

PART TEMP RANGE IC PACKAGE

MAX2828EVKIT

-40°C to +85°C 56 TQFN (T5688-2)

MAX2829EVKIT

-40°C to +85°C 56 TQFN (T5688-2)

Ordering Information

DESIGNATION

QTY

DESCRIPTION

C33 1

560pF ±5% 0402 capacitor

Murata GRM1555C1H561J

C34 1

150pF ±5% 0402 capacitor

Murata GRM1555C1H151J

C39, C51, C53

C55

10µF ±20% tantalum

capacitors—R case

AVX TAJR106M006R

C47 1

100pF ±5% 0402 capacitor

Murata GRM1555C1H101J

C65 1

0.5pF ±0.1pF 0201 capacitor

Murata GJM0335C1ER50B

J1–J9 9

Connectors—SMA end-launch

jack receptacles 0.062in

Johnson 142-0701-801

J12–J16, TP1–TP8,

TP10–TP23

Test points

5000K-ND

J18 1

Connector DB25—right angle,

male

AMP 747238-4

JP21, JP22 2

1 x 3 headers, 3-pin in-line

headers, 100 mils

Sullins S1012-36-ND

MAX2829 Component List

For the MAX2828, components that are connected to N.C. pins can be left open.

Evaluate: MAX2828/MAX2829

Quick Start

Each EV kit is fully assembled and factory tested.

Follow the instructions in the Connections and Setup

section to test the devices.

Test Equipment Required

This section lists the recommended test equipment to

verify the operation of the MAX2828/MAX2829. It is

intended as a guide only, and substitutions may be

possible.

• DC supply capable of delivering +5.0V and 200mA of

continuous current

• DC supply capable of delivering -5.0V and 200mA of

continuous current

• DC supply capable of delivering +3.6V and 300mA of

continuous current

• HP 8663A or equivalent low-noise signal source

capable of generating a 20MHz or 40MHz reference

oscillator signal

• Two HP 8648s or equivalent signal sources capable

of generating 0dBm up to 6GHz

• 802.11x I/Q waveform generator (optional)

• HP 8561E or equivalent RF spectrum analyzer with a

minimum 100kHz to 6GHz frequency range

• TDS3012 or equivalent oscilloscope with 200MHz

bandwidth

• IBM PC or a PC compatible with Windows

95/98/

2000/NT 4.0, or later operating system and an avail-

able parallel port

• Male-to-male 25-pin parallel cable, straight through

Connections and Setup

This section provides step-by-step instructions for get-

ting the EV kits up and running in all modes:

1) Install and run the MAX2828/MAX2829 control software.

2) To control the EV kit through the 3-wire interface,

connect the male-to-male 25-pin parallel cable

between the PC and EV kit.

3) With the power supply turned off, connect a +2.7V

power supply to the header labeled VCC (J13).

Connect the power-supply ground to the header

labeled GND (J12).

4) With the power supply turned off, connect a +5V

power supply to the header labeled +5V (J16), and

a -5V power supply to the header labeled -5V (J14).

Connect the power-supply ground to the header

labeled GND (J15).

5) Connect the low-noise signal source to FREF (J9).

MAX2828/MAX2829 Evaluation Kits

2 _______________________________________________________________________________________

Windows is a registered trademark of Microsoft Corp.

DESIGNATION

QTY

DESCRIPTION

L1 1

6.8nH ±5% 0402 inductor

Murata LQG15HN6N8J00

L2 1

2.0nH ±0.2nH 0201 inductor

Murata LQP03TN2N0C00

L6 1

3.6nH ±0.2nH 0402 inductor

Murata LQP15MN3N6C00

L7 1

1.8nH ±0.1nH 0402 inductor

Murata LQP15MN1N8B02

R1, R2, R6, R10,

R16, R17, R22,

R27

875Ω ±1% 0402 resistors

R3, R7, R18, R23,

R25

5 10kΩ ±1% 0402 resistors

R4, R5, R21, R26

4 49.9Ω ±1% 0402 resistors

R8, R9, R12, R13,

R19, R28, R29,

R31, R32, R36,

R42, R44

0Ω ±1% 0402 resistors

R14 1 267Ω ±1% 0402 resistor

DESIGNATION QTY DESCRIPTION

R15 1 11kΩ ±1% 0402 resistor

R20 1 620Ω ±0.01 0402 resistor

R24 1 300Ω ±0.01 0402 resistor

R34, R37 2 100kΩ ±1% 0402 resistors

R39, R40, R41 3 100Ω ±1% 0402 resistors

R43 1 1kΩ ±1% 0402 resistor

T1 1

HHM1711D1 balun

TDK HHM1711D1

T2 1

HHM1732B1 balun

TDK HHM1732B1

U1, U5 2 MAX4447ESE

U2, U6 2 MAX4444ESE

U3 1 MAX6061BEUR

U4 1 MAX2828ETN/MAX2829ETN

U8, U9 2

Texas Instruments

SN74LVTH244ADBR

MAX2829 Component List (continued)

6) Turn on the +5V and -5V power supplies, followed

by the +2.7V power supply. Set the low-noise signal

source to 20MHz and 2dBm. Enable the signal

source. The lock indicator should be green.

Receive Mode

To evaluate the devices in receive mode:

1) Set the RXON jumper (JP22) to the On position and

the TXON jumper (JP21) to the Off position.

2) Connect the RF signal source to either RXRFL

(802.11g, J4) or RXRFH (802.11a, J3). Set the RF

frequency to 2437MHz (802.11g) or 5.25GHz

(802.11a). Set the signal power to -100dBm.

3) Set the register setting to the default values listed in

the MAX2828/MAX2829 data sheet by clicking on

the “Send All” button. Use the software to select

between 802.11g and 802.11a modes. In the pro-

gram, set the frequency to either 2437MHz (802.11g)

or 5.25GHz (802.11a). Set the Rx gain to maximum

using either the slider bar or the control bits.

4) Connect the spectrum analyzer to either RXBBI or

RXBBQ. Set the center frequency to 5MHz with a

10MHz span.

5) Turn on the RF signal source. The output at 5MHz

should be approximately -4dBm (802.11g) or

-5dBm (802.11a).

Transmit Mode

To evaluate the devices in transmit mode:

1) Set the TXON jumper (JP21) to the On position and

the RXON jumper (JP22) to the Off position.

2) Connect a 2MHz I/Q signal to TXBBQ and TXBBI.

Set the input amplitude of each channel to

100mV

RMS

3) Set the register setting to the default values listed in

the MAX2828/MAX2829 data sheet by clicking on

the “Send All” button. Use the software to select

between 802.11g and 802.11a modes. In the pro-

gram, set the frequency to either 2437MHz (802.11g)

or 5.25GHz (802.11a). Set the Tx gain to maximum

using either the slider bar or the control bits.

4) Connect the spectrum analyzer to either TXRFL

(802.11g, J1) or TXRFH (802.11a, J2).

5) Turn on the baseband signal sources. The output

at RF should be approximately -2dBm (802.11g) or

-4dBm (802.11a).

Evaluate: MAX2828/MAX2829

MAX2828/MAX2829 Evaluation Kits

_______________________________________________________________________________________ 3

JUMPER

STATE

FUNCTION

JU21 Off

Enables transmit mode. Placing the

jumper toward the SPI™ connector

puts the device in transmit mode.

JU22 Off

Enables receive mode. Placing the

jumper toward the SPI connector

puts the device in receive mode.

Table 1. Jumper Functions

Table 2. Test Points

TP DESCRIPTION

TP1