EC6108V9A RK312X 1G 4G 升级固件亲测正常

#AP6234_NVRAM_V1.1_20131225 manfid=0x2d0 prodid=0x0653 vendid=0x14e4 devid=0x4386 boardtype=0x0653 boardrev=0x1203 boardnum=22 macaddr=00:90:4c:c5:12:38 sromrev=3 #boardflags: # bit 19 3tswitch: 2.4GHz FEM: SP3T switch share with BT # bit 16 nopa: no external pa # keep original 0x200 boardflags=0x0090201 xtalfreq=37400 nocrc=1 ag0=255 aa2g=1 ccode=ALL pa0itssit=0x20 #PA parameters for 2.4GHz pa0b0=6957 default #pa0b0=6727 pa0b1=-808 pa0b2=-178 tssifloor2g=69 # rssi params for 2.4GHz rssismf2g=0xf rssismc2g=0x8 rssisav2g=0x1 cckPwrOffset=3 # rssi params for 5GHz rssismf5g=0xf rssismc5g=0x7 #rssisav5g=0x1 rssisav5g=0x3 #PA parameters for lower a-band #pa1lob0=5659 default pa1lob0=5859 #pa1lob0=5659 pa1lob1=-693 pa1lob2=-178 tssifloor5gl=77 #PA parameters for midband pa1b0=5372 #pa1b0=5172 pa1b1=-671 pa1b2=-212 tssifloor5gm=77 #PA paramasdeters for high band #pa1hib0=5320 default pa1hib0=5620 #pa1hib1=-963 pa1hib1=-663 pa1hib2=-179 tssifloor5gh=74 rxpo5g=0 maxp2ga0=76 # 19.5dBm max; 18dBm target #Per rate power back-offs for g band, in .5 dB steps. Set it once you have the right numbers. cck2gpo=0x2222 ofdm2gpo=0x333333333 # R54 16dBm; R48 17dBm; others 18dBm mcs2gpo0=0x5555 # M0~ M4 17dBm mcs2gpo1=0x5555 # M5M6 15dBm; M7 14.5dBm #max power for 5G maxp5ga0=68 # 16dBm target; 17.5dBm Max maxp5gla0=68 maxp5gha0=68 #Per rate power back-offs for a band, in .5 dB steps. Set it once you have the right numbers. ofdm5gpo=0x66666666 # R54 13.5dBm ofdm5glpo=0x66666666 ofdm5ghpo=0x66666666 mcs5gpo0=0x8888 # M0~M4 16dBm (1dB higher than ofdm) mcs5gpo1=0x8888 # M5M6 13.5dBm; M7 12dBm mcs5glpo0=0x7777 mcs5glpo1=0x7777 mcs5ghpo0=0x7777 mcs5ghpo1=0x7777 # Parameters for DAC2x mode and ALPF bypass # RF SW Truth Table: ctrl0 for BT_TX; ctrl1 or 5G Tx; ctrl2 for 5G Rx; Ctrl3 for 2G Tx; Ctrl4 for 2G Rx swctrlmap_2g=0x00080008,0x00100010,0x00080008,0x011010,0x11f swctrlmap_5g=0x00040004,0x00020002,0x00040004,0x011010,0x2fe gain=32 triso2g=8 triso5g=8 #tx parameters loflag=0 iqlocalidx5g=40 dlocalidx5g=70 iqcalidx5g=50 lpbckmode5g=1 txiqlopapu5g=0 txiqlopapu2g=0 dlorange_lowlimit=5 txalpfbyp=1 txalpfpu=1 dacrate2xen=1 papden2g=1 papden5g=1 #rx parameters gain_settle_dly_2g=4 gain_settle_dly_5g=4 noise_cal_po_2g=-1 noise_cal_po_40_2g=-1 noise_cal_high_gain_2g=73 noise_cal_nf_substract_val_2g=346 noise_cal_po_5g=-1 noise_cal_po_40_5g=-1 noise_cal_high_gain_5g=73 noise_cal_nf_substract_val_5g=346 cckpapden=0 # Enable OOB interrupt: level trigger muxenab=0x10