没有合适的资源?快使用搜索试试~ 我知道了~
资源详情
资源评论
资源推荐
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 1.2 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 29, 2021
AN332
Si47XX PROGRAMMING GUIDE
1. Introduction
This document provides an overview of the programming requirements for the Si4704/05/06/07/1x/2x/3x/4x/84/85
FM transmitter/AM/FM/SW/LW/WB receiver. The hardware control interface and software commands are detailed
along with several examples of the required steps to configure the device for various modes of operation.
2. Overview
This family of products is programmed using commands and responses. To perform an action, the system
controller writes a command byte and associated arguments, causing the device to execute the given command.
The device will, in turn, provide a response depending on the type of command that was sent. Section "4.
Commands and Responses" on page 6 and Section "5. Commands and Properties" on page 7 describe the
procedures for using commands and responses and provide complete lists of commands, properties, and
responses.
The device has a slave control interface that allows the system controller to send commands to and receive
responses from the device using one of three serial protocols (or bus modes): 2-wire mode (I
2
C and SMBUS
compatible), 3-wire mode, or SPI mode.
Section "6. Control Interface" on page 223 describes the control interface in detail.
Section "7. Powerup" on page 231 describes options for the sequencing of VDD and VIO power supplies, selection
of the desired bus mode, provision of the reference clock, RCLK, and sending of the POWER_UP command.
Section "8. Powerdown" on page 238 describes sending the POWER_DOWN command and removing VDD and
VIO power supplies as necessary.
Section "9. Digital Audio Interface" on page 239 describes the digital audio format supported and how to operate
the device in digital mode.
Section "10. Timing" on page 242 describes the CTS (Clear to Send) timing indicating when the command has
been accepted and in most cases completed execution, and the STC (Seek/Tune Complete) timing indicating
when the Seek/Tune commands have completed execution.
Section "11. FM Transmitter" on page 248 describes the audio dynamic range control, limiter, pre-emphasis,
recommendations for maximizing audio volume for the FM transmitter.
Section "12. Programming Examples" on page 252 provides flowcharts and step-by-step procedures for
programming the device.
AN332
2 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 1.2 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 29, 2021
Table 1. Product Family Function
Part
Number
General Description
FM Transmitter
FM Receiver
AM Receiver
SW/LW Receiver
WB Receiver
RDS
High Performance RDS
RPS
SAME
Digital Input
Digital Output
Embedded FM antenna
AEC-Q100 Qualified
Package Size (mm)
Si4700 FM Receiver
4x4
Si4701 FM Receiver with RDS
4x4
Si4702 FM Receiver
3x3
Si4703 FM Receiver with RDS
3x3
Si4704 FM Receiver
1
3x3
Si4705 FM Receiver with RDS
2
3x3
Si4706
3
High Performance RDS Receiver
3x3
Si4707
3
WB Receiver with SAME
3x3
Si4708 FM Receiver
2.5x2.5
Si4709 FM Receiver with RDS
2.5x2.5
Si4710
4
FM Transmitter
3x3
Si4711 FM Transmitter with RDS
3x3
Si4712
4
FM Transmitter with RPS
3x3
Si4713 FM Transmitter with RDS & RPS
3x3
Si4720
4
FM Transceiver
3x3
Si4721 FM Transceiver with RDS
3x3
Si4730 AM/FM Receiver
3x3
Si4731 AM/FM Receiver with RDS
2
3x3
Si4732
5
AM/SW/LW/FM Receiver with RDS
SOIC16
Si4734 AM/SW/LW/FM Receiver
3x3
Si4735 AM/SW/LW/FM Receiver with RDS
2
3x3
Si4736 AM/FM/WB Receiver
3x3
Notes:
1. Digital Output is available in Si4704-D60 and later.
2. High Performance RDS is available in Si4705/31/35/85-D50 and later, Si4732.
3. Si4706, Si4707, and Si474x are covered under NDA.
4. There is an errata for the digital audio input for Si4710-B30, Si4712-B30, and Si4720-B20. A patch is available to
enable digital audio input for these devices. Please contact Skyworks Solutions to request a patch.
5. Si4732-A10 has the same firmware FMRX component and AM_SW_LW RX component as that of Si4735-D60, so
Si4732-A10 is considered as the most recent revision as D60, and the Si4735-D60 related descriptions in Appendix A
and Appendix B also apply to Si4732-A10 if not specified.
AN332
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 3
Rev. 1.2 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 29, 2021
Si4737 AM/FM/WB Receiver with RDS
3x3
Si4738 FM/WB Receiver
3x3
Si4739 FM/WB Receiver with RDS
3x3
Si4740
3
AM/FM Receiver
4x4
Si4741
3
AM/FM Receiver with RDS
4x4
Si4742
3
AM/LW/SW/FM/WB Receiver
4x4
Si4743
3
AM/LW/SW/FM/WB Receiver with
RDS
4x4
Si4744
3
AM/LW/SW/FM Receiver
4x4
Si4745
3
AM/LW/SW/FM Receiver with RDS
4x4
Si4749
3
High-Performance RDS Receiver
4x4
Si4784 FM Receiver
3x3
Si4785 FM Receiver with RDS
2
3x3
Table 1. Product Family Function (Continued)
Notes:
1. Digital Output is available in Si4704-D60 and later.
2. High Performance RDS is available in Si4705/31/35/85-D50 and later, Si4732.
3. Si4706, Si4707, and Si474x are covered under NDA.
4. There is an errata for the digital audio input for Si4710-B30, Si4712-B30, and Si4720-B20. A patch is available to
enable digital audio input for these devices. Please contact Skyworks Solutions to request a patch.
5. Si4732-A10 has the same firmware FMRX component and AM_SW_LW RX component as that of Si4735-D60, so
Si4732-A10 is considered as the most recent revision as D60, and the Si4735-D60 related descriptions in Appendix A
and Appendix B also apply to Si4732-A10 if not specified.
AN332
4 Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
Rev. 1.2 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 29, 2021
TABLE OF CONTENTS
Section Page
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
2. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
3. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
4. Commands and Responses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
5. Commands and Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
5.1. Commands and Properties for the FM/RDS Transmitter (Si4710/11/12/13/20/21) . . .7
5.2. Commands and Properties for the FM/RDS Receiver
(Si4704/05/06/2x/3x/4x/84/85) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
5.3. Commands and Properties for the AM/SW/LW Receiver
(Si4730/31/32/34/35/36/37/40/41/42/43/44/45) . . . . . . . . . . . . . . . . . . . . . . . . . . . .123
5.4. Commands and Properties for the WB Receiver (Si4707/36/37/38/39/42/43) . . . .170
5.5. Commands and Properties for the Stereo Audio ADC Mode (Si4704/05/30/31) . .204
6. Control Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .223
6.1. 2-Wire Control Interface Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .223
6.2. 3-Wire Control Interface Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .226
6.3. SPI Control Interface Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .229
7. Powerup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .231
7.1. Powerup from Device Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .232
7.2. Powerup from a Component Patch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .233
8. Powerdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .238
9. Digital Audio Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .239
10. Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .242
11. FM Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .248
11.1. Audio Dynamic Range Control for FM Transmitter . . . . . . . . . . . . . . . . . . . . . . . .248
11.2. Audio Pre-emphasis for FM Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .249
11.3. Audio Limiter for FM Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
250
11.4. Maximizing Audio Volume for FM Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . .250
12. Programming Examples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .252
12.1. Programming Example for the FM/RDS Transmitter . . . . . . . . . . . . . . . . . . . . . .252
12.2. Programming Example for the FM/RDS Receiver . . . . . . . . . . . . . . . . . . . . . . . .270
12.3. Programming Example for the AM/LW/SW Receiver . . . . . . . . . . . . . . . . . . . . . .292
12.4. Programming Example for the WB/SAME Receiver . . . . . . . . . . . . . . . . . . . . . . .302
Appendix A—Comparison of the Si4704/05/3x-B20,
Si4704/05/3x-C40, and Si4704/05/3x-D60 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .312
Appendix B—Si4704/05/3x-B20/-C40/-D60 Compatibility Checklist . . . . . . . . . . . . . . . .316
Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .319
Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .321
AN332
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 5
Rev. 1.2 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • December 29, 2021
3. Terminology
SEN—Serial enable pin, active low; used as device select in 3-wire and SPI operation and address selection in
2-wire operation.
SDIO—Serial data in/data out pin.
SCLK—Serial clock pin.
RST or RSTb—Reset pin, active low
RCLK—External reference clock
GPO—General purpose output
CTS—Clear to send
STC—Seek/Tune Complete
NVM—Non-volatile internal device memory
Device—Refers to the FM Transmitter/AM/FM/SW/LW/WB Receiver
System Controller—Refers to the system microcontroller
CMD—Command byte
COMMANDn—Command register (16-bit) in 3-Wire mode (n = 1 to 4)
ARGn—Argument byte (n = 1 to 7)
STATUS—Status byte
RESPn—Response byte (n = 1 to 15)
RESPONSEn—Response register (16-bit) in 3-Wire mode (n = 1 to 8)
剩余320页未读,继续阅读
baidu_20358801
- 粉丝: 2
- 资源: 10
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
最新资源
- 农村信用社联合社计算机信息系统投产与变更管理办.docx
- 农村信用社联合社计算机信息系统数据管理办法.docx
- 利用SPSS作临床效度分析线上计算网站介绍-医学研究部统计谘.(医学PPT课件).ppt
- 利用Zabbix监控mysqldump定时备份数据库状态.docx
- 利用计算机解决问题的基本过程.doc
- 化工铁路通信工程总结.doc
- 北京大学网络教育软件工程作业.docx
- 医药公司(连锁店)计算机操作规程未新系统的自行按照旧制修改-新系统过制的编号加修模版.doc
- 医药公司(连锁店)计算机系统操作规程模版.doc
- 医药连锁门店计算机系统的操作和管理程序未新系统的自行按照旧制修改-新系统过制的编号加修模版.docx
资源上传下载、课程学习等过程中有任何疑问或建议,欢迎提出宝贵意见哦~我们会及时处理!
点击此处反馈
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功
评论0